Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(w/ VSC) › from 2012.10
RM1840EF _57 Power Source / Network _009639 NETWORKING _0052677 CAN COMMUNICATION SYSTEM(w/ VSC) D

NETWORKING  CAN COMMUNICATION SYSTEM(w/ VSC)  DIAGNOSIS SYSTEM  


BUS CHECK (COMMUNICATION MALFUNCTION ECU)


Only CAN communication system DTCs for each ECU can be output to the intelligent tester.

a.
C128170

Select "Bus Check" from the "System Select" screen on the intelligent tester.


b.
C128171

Select "Communication Malfunction DTC" from the "Bus Check" screen, and then select "Enter".


c.
C128172

Select the system of the DTC to be checked and select "Details".


d.
C128173

CAN communication system DTCs are output.



BUS CHECK (COMMUNICATION BUS CHECK)


HINT:

The ECUs and sensors that are properly connected to the CAN communication system can be displayed using the intelligent tester.


a.
C128171

Select "Communication Bus Check" from the "Bus Check" screen.


b.

The screen displays the ECUs and sensors that are properly connected to the CAN communication system.

HINT:
·

If any properly connected ECUs or sensors are not displayed, there is a communication stop in the system (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(w/ VSC)>PROBLEM SYMPTOMS TABLE).

·

The default item displayed in the combo box is "ALL". When checking the ECUs (sensors) connected to each bus, pull down the combo box and select the bus to be checked from the drop-down list. The drop-down list displays "ALL", "V Bus" and the names of the remaining buses.

Combo Box Display Content
ALL All ECUs (sensors) connected to the CAN bus
V Bus ECUs (sensors) connected to the V Bus
Bus Name ECUs (sensors) connected to the selected bus

·

The connection status (shown below) is indicated by the background color displayed behind the system name.

ECU (Sensor) on V Bus
Background Color Connection Status
White Detected normally
Yellow Could not be detected in the past, but is currently detected
Red Detected in the past, but cannot be detected now
Not displayed Has never been detected

ECU (Sensor) with No Data Monitor History
Background Color Connection Status
White Detected normally
Yellow Could not be detected in the past, but is currently detected
Red Detected in the past, but cannot be detected now
Not displayed Has never been detected

ECU (Sensor) with Data Monitor History
Background Color Connection Status
White Detected normally
Yellow Could not be detected in the past, but is currently detected
Red Detected in the past, but cannot be detected now
Red Has never been detected but has connection history
Not displayed Has never been detected




c.
C232151

"There is no system connected to the communication bus." is displayed if there are no ECUs or sensors connected to the CAN bus.



CHECK INSTALLED SYSTEMS (ECUS AND SENSORS) THAT USE CAN COMMUNICATION


a.

Systems (ECUs and sensors) that use CAN communication vary depending on the optional settings of the vehicle. Check which systems (ECUs and sensors) are installed on the vehicle.

ECU/Sensor Name Tester Display Installed on
ECM ECM (Engine) All vehicles
Transmission control ECU assembly (TCM) TCM All vehicles
Brake actuator assembly (skid control ECU) Skid Control (ABS/VSC/TRAC) All vehicles
Yaw rate sensor assembly Yaw Rate Sensor All vehicles
Spiral cable sub-assembly (steering angle sensor) Spiral cable (Steering Angle Sensor) All vehicles



DTC TABLE BY ECU


HINT:
·

In the CAN communication system, CAN communication system DTCs stored by an ECU can be output by using the intelligent tester.

·

If CAN communication system DTCs are output, the trouble cannot be determined solely from the DTCs. Perform troubleshooting according to "How to Proceed with Troubleshooting" (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(w/ VSC)>HOW TO PROCEED WITH TROUBLESHOOTING).



a.

ECM

HINT:

DTC communication uses the CAN communication system.


DTC Code Detection Item
U0101* Lost Communication with TCM



b.

TRANSMISSION CONTROL ECU ASSEMBLY (TCM)

HINT:

DTC communication uses the CAN communication system.


DTC Code Detection Item
U0100* Lost Communication with ECM/PCM "A"



c.

BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)

HINT:

DTC communication uses the CAN communication system.


DTC Code Detection Item
U0073 Control Module Communication Bus Off
U0100 Lost Communication with ECM/PCM "A"
U0123 Lost Communication with Yaw Rate Sensor Module
U0124 Lost Communication with Lateral Acceleration Sensor Module
U0126 Lost Communication with Steering Angle Sensor Module


d.

YAW RATE SENSOR ASSEMBLY

HINT:

The yaw rate sensor assembly is connected to the CAN communication system but CAN communication DTCs are not stored.



e.

SPIRAL CABLE SUB-ASSEMBLY (STEERING ANGLE SENSOR)

HINT:

The spiral cable sub-assembly (steering angle sensor) is connected to the CAN communication system but CAN communication DTCs are not stored.




DTC COMBINATION TABLE


HINT:
·

○: Stored.

·

-: Not stored.



V Bus
Output from Output DTC Detection Item Detected Communication Stop Mode
V Bus
Skid Control ECU Communication Stop Mode Yaw Rate Sensor Communication Stop Mode Steering Angle Sensor Communication Stop Mode ECM Communication Stop Mode
Brake actuator assembly (skid control ECU) U0073 Control Module Communication Bus Off ○ - - -
U0100 Lost Communication with ECM/PCM "A" ○ - - ○
U0123 Lost Communication with Yaw Rate Sensor Module ○ ○ - -
U0124 Lost Communication with Lateral Acceleration Sensor Module ○ ○ - -
U0126 Lost Communication with Steering Angle Sensor Module ○ - ○ -