Home › Drivetrain › A750F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV without i-ART) › from 2012.10
RM1840EF _52 Drivetrain _009612 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0052508 AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV without i-ART) C

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV without i-ART)  P0894  Transmission Component Slipping  P2714  Pressure Control Solenoid "D" Performance (Shift Solenoid Valve SLT)  


DESCRIPTION

Refer to DTC P2716 (See page Drivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV without i-ART)>P2716).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0894 Transmission Component Slipping The TCM detects a malfunction of the SLT, S1, S2, SR, SL1, SL2 or 1-2 shift solenoid valves according to the revolution difference of the turbine and output shaft, and also by the oil pressure (2 trip detection logic).
·

Shift solenoid valve SLT remains open or closed

·

Shift solenoid valve S1, S2, SR, SL1 or SL2 remains open or closed

·

1-2 shift valve is stuck

·

Valve body is blocked

·

Automatic transmission (clutch, brake or gear, etc.)


Comes on DTC stored
P2714 Pressure Control Solenoid "D" Performance (Shift Solenoid Valve SLT) The TCM detects a malfunction of the SLT shift solenoid valve (ON side) according to the revolution difference of the turbine and output shaft, and also by the oil pressure (2 trip detection logic).
·

Shift solenoid valve SLT remains open or closed

·

Shift solenoid valve S1, S2, SR, SL1 or SL2 remains open or closed

·

1-2 shift valve is stuck

·

Valve body is blocked

·

Automatic transmission (clutch, brake or gear, etc.)


Comes on DTC stored

MONITOR DESCRIPTION

The TCM calculates the amount of heat absorbed by the friction material based on the difference in revolution (clutch slippage) between the turbine and output shaft. The TCM turns on the MIL and stores this DTC when the amount of heat absorption exceeds the specified value.

There are two reasons that make the revolution different.

·

When the shift solenoid valve SLT remains on, oil pressure goes down and clutch engagement force decreases.

·

When the shift solenoid valve remains on or off, the gear position commanded by the TCM and the actual gear position are not the same.


NOTICE:

If you continue driving under these conditions, the clutch will burn out and the vehicle will no longer be drivable.


PROCEDURE

1.CHECK DTC OUTPUT (IN ADDITION TO DTCS P0894 AND P2714)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / ECT / DTC.

Powertrain > ECT > Trouble Codes
50001 64

e.

Read the DTCs using the tester.

Result:
Result Proceed to
P0894 and/or P2714 is output A
P0894, P2714 and other DTCs are output B


HINT:

If any other codes besides P0894 and P2714 are output, perform troubleshooting for those DTCs first.




A

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SHIFT SOLENOID VALVE SLT)

B

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SHIFT SOLENOID VALVE SLT)
NOTICE:
·

Perform the test while the ATF temperature is between 50 and 80°C (122 and 176°F).

·

Be careful to prevent the hose of SST from interfering with the exhaust pipe.

·

Perform the test with the A/C off.



HINT:

Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.
C214323N05
0.594,1.198 0.594,1.688 0.594,1.688 0.427,1.688 false 2.75,1.24 2.75,1.688 2.75,1.688 2.906,1.688 true 0.125,1.615 0.479,1.813 0.354,0.198 10 false SST 2.99,1.604 3.313,1.802 0.323,0.198 10 false SST

Remove the test plug from the transmission case and connect SST.


SST
09992-00095  (09992-00231, 09992-00271)

b.

Connect the intelligent tester to the DLC3.


c.

Start the engine and warm it up.


d.

Measure the line pressure with SST.


e.

Turn the intelligent tester on.


f.

Enter the following menus: Powertrain / ECT / Active Test.


g.

According to the display on the tester, perform the Active Test.


h.

Measure the line pressure.

Powertrain > ECT > Active Test
Tester Display
Activate the Solenoid (SLT)
50004 64 130
Powertrain > ECT > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Activate the Solenoid (SLT) Operate shift solenoid valve SLT and raise line pressure ON or OFF
HINT:
·

OFF: Line pressure up (when Active Test "Activate the Solenoid (SLT)" is performed, TCM commands shift solenoid valve SLT to turn OFF)

·

ON: No action (normal operation)



[Vehicle Condition]
·

Vehicle stopped

·

Engine idling


HINT:

Activate the Solenoid (SLT) in the Active Test is performed to check the line pressure changes by connecting SST to the automatic transmission, which is used in the Hydraulic Test (Drivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV without i-ART)>HYDRAULIC TEST) as well. Note that the pressure values in the Active Test and hydraulic test are different.


OK:

The line pressure changes as specified when performing the Active Test.



Result:
Proceed to
OK
NG



OK

3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (RUNNING TEST)

NG

17.INSPECT SHIFT SOLENOID VALVE SLT
3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (RUNNING TEST)
CAUTION:

This test should always be performed with at least 2 people.


NOTICE:
·

Perform the test while the ATF temperature is between 50 and 80°C (122 and 176°F).

·

Perform the test with the A/C turned off.



HINT:

Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Connect the intelligent tester to the DLC3.



c.

Warm up the engine.


d.

Enter the following menus: Powertrain / ECT / Active Test.


e.

According to the display on the tester, perform the Active Test.

HINT:

While driving, the shift position can be forcibly changed with the intelligent tester.


Powertrain > ECT > Active Test
Active Test Display
Control the Shift Position
Data List Display
Shift Status
50004 64 116 181
Powertrain > ECT > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Control the Shift Position Operate shift solenoid valves and set each shift position
·

Press "→" button: Shift up

·

Press "←" button: Shift down


Possible to check operation of the shift solenoid valves.
[Vehicle Condition]
50 km/h (31 mph) or less
HINT:
·

This test can be conducted when the vehicle speed is 50 km/h (31 mph) or less.

·

The 4th to 5th up-shift must be performed with the accelerator pedal released.

·

The 5th to 4th down-shift must be performed with the accelerator pedal released.

·

Do not operate the accelerator pedal for at least 2 seconds after shifting and do not shift successively.

·

The shift position commanded by the TCM is shown in the Data List display on the intelligent tester.




f.

Compare the TCM gear shift command and the actual gear position.

OK:

Gear position changes in accordance with the tester command.



Result:
System Condition TCM Gear Shift Command Proceed to
1st 2nd 3rd 4th 5th
Malfunction Shift solenoid valve S1 Stuck ON 1st 2nd 2nd 1st N*1 A
Stuck OFF 4th 3rd 3rd 4th 5th
Shift solenoid valve S2 Stuck ON*2 2nd 2nd 3rd 3rd N*1 B
Stuck OFF*3 1st 1st 4th 4th 5th
Shift solenoid valve SL2 Stuck ON 1st 2nd 3rd 4th N*1 C
Stuck OFF 1st 2nd 3rd 4th 5th
Shift solenoid valve SR Stuck ON*4 1st 2nd 3rd 4th 5th D
Stuck OFF*5 1st 2nd 3rd 4th 4th
Normal 1st 2nd 3rd 4th 5th E


HINT:
·

*1: Neutral

·

*2: When shift solenoid valve S2 is stuck ON, the vehicle cannot drive in reverse.

·

*3: When shift solenoid valve S2 is stuck OFF, the 4th to 5th up-shift will have a large shift shock. Also, the 5th to 4th down-shift will have time lag.

·

*4: When shift solenoid valve SR is stuck ON, the condition can be determined by checking if shift shock has increased excessively.

·

*5: When shift solenoid valve SR is stuck OFF, moving the shift lever from N to D will cause a large shift shock.

·

Gear shift can be determined by paying attention to changes in engine speed.




A

4.INSPECT SHIFT SOLENOID VALVE S1

B

7.INSPECT SHIFT SOLENOID VALVE S2

C

10.INSPECT SHIFT SOLENOID VALVE SL2

D

13.INSPECT SHIFT SOLENOID VALVE SL1

E

17.INSPECT SHIFT SOLENOID VALVE SLT
4.INSPECT SHIFT SOLENOID VALVE S1
a.
C214327C06
0.052,0.042 0.281,0.188 0.229,0.146 10 false *a 2.479,0.281 2.813,0.531 0.333,0.25 10 false (+) 3.208,0.26 3.427,0.5 0.219,0.24 10 false (-)
*a Component without harness connected
(Shift Solenoid Valve S1)


Remove shift solenoid valve S1.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Shift solenoid valve S1 connector terminal - Shift solenoid valve S1 body 20°C (68°F) 11 to 15 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) → Shift solenoid valve S1 connector

·

Battery negative (-) → Shift solenoid valve S1 body


Valve moves and makes an operating noise



Result:
Proceed to
OK
NG



OK

5.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

NG

5.INSPECT TRANSMISSION VALVE BODY ASSEMBLY
a.

Check the transmission valve body assembly.

Click hereDrivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>VALVE BODY ASSEMBLY>DISASSEMBLY

OK:

There are no foreign objects on any valve.



Result:
Proceed to
OK
NG



OK

6.INSPECT TORQUE CONVERTER ASSEMBLY

NG

REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY

6.INSPECT TORQUE CONVERTER ASSEMBLY
a.

Check the torque converter assembly.

Click hereDrivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>TORQUE CONVERTER AND DRIVE PLATE>INSPECTION

OK:

The torque converter assembly operates normally.



Result:
Proceed to
OK
NG



OK

NG

7.INSPECT SHIFT SOLENOID VALVE S2
a.
C214328C05
0.063,0.073 0.313,0.271 0.25,0.198 10 false *a 1.76,0.271 1.958,0.469 0.198,0.198 10 false (-) 2.5,0.26 2.729,0.458 0.229,0.198 10 false (+)
*a Component without harness connected
(Shift Solenoid Valve S2)


Remove shift solenoid valve S2.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Shift solenoid valve S2 connector terminal - Shift solenoid valve S2 body 20°C (68°F) 11 to 15 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) → Shift solenoid valve S2 connector

·

Battery negative (-) → Shift solenoid valve S2 body


Valve moves and makes an operating noise



Result:
Proceed to
OK
NG



OK

8.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

NG

8.INSPECT TRANSMISSION VALVE BODY ASSEMBLY
a.

Check the transmission valve body assembly.

Click hereDrivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>VALVE BODY ASSEMBLY>DISASSEMBLY

OK:

There are no foreign objects on any valve.



Result:
Proceed to
OK
NG



OK

9.INSPECT TORQUE CONVERTER ASSEMBLY

NG

REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY

9.INSPECT TORQUE CONVERTER ASSEMBLY
a.

Check the torque converter assembly.

Click hereDrivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>TORQUE CONVERTER AND DRIVE PLATE>INSPECTION

OK:

The torque converter assembly operates normally.



Result:
Proceed to
OK
NG



OK

NG

10.INSPECT SHIFT SOLENOID VALVE SL2
a.
C197715C22
1.781,0.958 2.229,0.375 true 1.469,0.958 1.01,0.375 true 1.76,2.948 2.208,2.354 true 1.469,2.948 1.01,2.354 true 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a 2.25,0.229 2.417,0.427 0.167,0.198 10 false 1 0.896,0.24 1.063,0.438 0.167,0.198 10 false 2 2.25,2.219 2.417,2.417 0.167,0.198 10 false 1 0.917,2.219 1.083,2.417 0.167,0.198 10 false 2 1.927,3.927 2.156,4.125 0.229,0.198 10 false (+) 1.167,3.927 1.396,4.125 0.229,0.198 10 false (-)
*a Component without harness connected
(Shift Solenoid Valve SL2)


Remove shift solenoid valve SL2.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) with a 21 W bulb → Terminal 1

·

Battery negative (-) → Terminal 2


Valve moves and makes an operating noise



Result:
Proceed to
OK
NG



OK

11.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

NG

11.INSPECT TRANSMISSION VALVE BODY ASSEMBLY
a.

Check the transmission valve body assembly.

Click hereDrivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>VALVE BODY ASSEMBLY>DISASSEMBLY

OK:

There are no foreign objects on any valve.



Result:
Proceed to
OK
NG



OK

12.INSPECT TORQUE CONVERTER ASSEMBLY

NG

REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY

12.INSPECT TORQUE CONVERTER ASSEMBLY
a.

Check the torque converter assembly.

Click hereDrivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>TORQUE CONVERTER AND DRIVE PLATE>INSPECTION

OK:

The torque converter assembly operates normally.



Result:
Proceed to
OK
NG



OK

NG

13.INSPECT SHIFT SOLENOID VALVE SL1
a.
C197715C22
1.781,0.958 2.229,0.375 true 1.469,0.958 1.01,0.375 true 1.76,2.948 2.208,2.354 true 1.469,2.948 1.01,2.354 true 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a 2.25,0.229 2.417,0.427 0.167,0.198 10 false 1 0.896,0.24 1.063,0.438 0.167,0.198 10 false 2 2.25,2.219 2.417,2.417 0.167,0.198 10 false 1 0.917,2.219 1.083,2.417 0.167,0.198 10 false 2 1.927,3.927 2.156,4.125 0.229,0.198 10 false (+) 1.167,3.927 1.396,4.125 0.229,0.198 10 false (-)
*a Component without harness connected
(Shift Solenoid Valve SL1)


Remove shift solenoid valve SL1.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) with a 21 W bulb → Terminal 1

·

Battery negative (-) → Terminal 2


Valve moves and makes an operating noise



Result:
Proceed to
OK
NG



OK

14.INSPECT SHIFT SOLENOID VALVE SR

NG

14.INSPECT SHIFT SOLENOID VALVE SR
a.
C214329C07
0.083,0.042 0.333,0.24 0.25,0.198 10 false *a 1.729,0.302 1.917,0.5 0.188,0.198 10 false (-) 2.479,0.292 2.729,0.49 0.25,0.198 10 false (+)
*a Component without harness connected
(Shift Solenoid Valve SR)


Remove shift solenoid valve SR.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Shift solenoid valve SR connector terminal - Shift solenoid valve SR body 20°C (68°F) 11 to 15 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) → Shift solenoid valve SR connector

·

Battery negative (-) → Shift solenoid valve SR body


Valve moves and makes operating noise



Result:
Proceed to
OK
NG



OK

15.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

NG

15.INSPECT TRANSMISSION VALVE BODY ASSEMBLY
a.

Check the transmission valve body assembly.

Click hereDrivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>VALVE BODY ASSEMBLY>DISASSEMBLY

OK:

There are no foreign objects on any valve.



Result:
Proceed to
OK
NG



OK

16.INSPECT TORQUE CONVERTER ASSEMBLY

NG

REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY

16.INSPECT TORQUE CONVERTER ASSEMBLY
a.

Check the torque converter assembly.

Click hereDrivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>TORQUE CONVERTER AND DRIVE PLATE>INSPECTION

OK:

The torque converter assembly operates normally.



Result:
Proceed to
OK
NG



OK

NG

17.INSPECT SHIFT SOLENOID VALVE SLT
a.
C209928C32
1.76,0.948 2.208,0.365 false 1.51,0.948 1.052,0.365 false 1.76,2.948 2.208,2.354 false 1.51,2.948 1.052,2.354 false 0.052,0 0.365,0.198 0.313,0.198 10 false *a 2.24,0.229 2.406,0.427 0.167,0.198 10 false 1 0.948,0.24 1.115,0.438 0.167,0.198 10 false 2 2.24,2.219 2.406,2.417 0.167,0.198 10 false 1 0.938,2.229 1.104,2.427 0.167,0.198 10 false 2 1.927,3.948 2.125,4.146 0.198,0.198 10 false (-) 1.115,3.969 1.333,4.167 0.219,0.198 10 false (+)
*a Component without harness connected
(Shift Solenoid Valve SLT)


Remove shift solenoid valve SLT.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) with a 21 W bulb → Terminal 2

·

Battery negative (-) → Terminal 1


Valve moves and makes an operating noise



Result:
Proceed to
OK
NG



OK

18.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

NG

18.INSPECT TRANSMISSION VALVE BODY ASSEMBLY
a.

Check the transmission valve body assembly.

Click hereDrivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>VALVE BODY ASSEMBLY>DISASSEMBLY

OK:

There are no foreign objects on any valve.



Result:
Proceed to
OK
NG



OK

19.INSPECT TORQUE CONVERTER ASSEMBLY

NG

REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY

19.INSPECT TORQUE CONVERTER ASSEMBLY
a.

Check the torque converter assembly.

Click hereDrivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>TORQUE CONVERTER AND DRIVE PLATE>INSPECTION

OK:

The torque converter assembly operates normally.



Result:
Proceed to
OK
NG



OK

NG