Home › Drivetrain › CLUTCH › CLUTCH PEDAL
RM1840EF _52 Drivetrain _009613 CLUTCH _0052510 CLUTCH PEDAL A

CLUTCH  CLUTCH PEDAL  INSTALLATION  


PROCEDURE

Hide 1.INSTALL NO. 2 CLUTCH PEDAL CUSHION (w/ Clutch Switch)

a.
C223750

Install the No. 2 clutch pedal cushion to the clutch pedal sub-assembly.


Hide 2.INSTALL PEDAL SPRING HOOK (w/ Turnover)

a.
C284476
1.24,1.417 1.313,1.417 false
V100135

MP grease


Apply MP grease to the contact surface of the pedal spring hook and install the hook to the clutch pedal support sub-assembly.


Hide 3.INSTALL CLUTCH MASTER CYLINDER PUSH ROD CLEVIS BUSH

a.
C283352
0.729,1.396 0.771,1.469 false
V100135

MP grease


Apply MP grease to the inside of a new clutch master cylinder push rod clevis bush.


b.

Install the clevis bush to the clutch pedal sub-assembly.

HINT:

Install the clevis bush from the left side of the vehicle.



Hide 4.INSTALL NO. 1 CLUTCH PEDAL CUSHION

a.
C223747

Install the No. 1 clutch pedal cushion to the clutch pedal sub-assembly.


Hide 5.INSTALL CLUTCH PEDAL BUSH

a.
C283353
1.271,0.854 1.313,0.802 false
V100135

MP grease


Apply MP grease to the collar and the inside and outside of 2 new clutch pedal bushes.


b.

Install the 2 bushes and collar to the clutch pedal sub-assembly.


Hide 6.INSTALL CLUTCH PEDAL TURNOVER BUSH (w/ Turnover)

a.
C283354
2.385,0.146 2.365,0.24 false
V100135

MP grease


Apply MP grease to the inside of the clutch pedal turnover bush and install the bush to the clutch pedal sub-assembly.


Hide 7.INSTALL CLUTCH PEDAL SPRING HOLDER (w/ Turnover)

a.
C283355
2.021,0.708 2.094,0.625 false
V100135

MP grease


Apply MP grease to the contact surface of the clutch pedal spring holder and install the holder to the clutch pedal support sub-assembly.


Hide 8.INSTALL CLUTCH PEDAL SUB-ASSEMBLY

a.

Install the clutch pedal sub-assembly to the clutch pedal support sub-assembly with the bolt and nut.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)

HINT:

Install the bolt from the right side of the vehicle.



b.
C223741
1.156,1.354 1.26,1.313 false
V100135

MP grease


w/ Turnover:

Apply MP grease to the inside of the hole in the hook and to the sliding areas of the spring, and then install the pedal spring with hook.


Hide 9.INSTALL CLUTCH PEDAL SPRING (w/ Turnover)

a.

Move the pedal to the full stroke position.


b.

Install the clutch pedal spring to the clutch pedal assembly.


Hide 10.INSTALL CLUTCH SWITCH ASSEMBLY (w/ Clutch Switch)

Hide 11.INSTALL CLUTCH PEDAL PAD

Hide 12.INSTALL CLUTCH PEDAL ASSEMBLY

C223739
0.823,0.74 0.958,0.896 0.135,0.156 10 false A 1.906,0.927 2.042,1.083 0.135,0.156 10 false A 1.906,0.031 2.031,0.188 0.125,0.156 10 false B

a.

Install the clutch pedal with the bolt and 2 nuts.

Torque:
for nut A : 14 N*m (145 kgf*cm, 10 ft.*lbf)
for bolt B : 18 N*m (184 kgf*cm, 13 ft.*lbf)


b.

w/ Clutch Switch:

Connect the clutch switch connector.


Hide 13.CONNECT CLUTCH MASTER CYLINDER PUSH ROD CLEVIS

a.
C283359
2.073,1.208 2.094,1.135 false
V100135

MP grease


Apply MP grease to the contact surface of the clevis pin.


b.

Connect the clutch master cylinder push rod clevis with the clevis pin and install a new clip.


c.

w/o Turnover:

Connect the clutch pedal spring to the clevis pin and clutch pedal support to install it.


Hide 14.INSPECT AND ADJUST CLUTCH PEDAL ASSEMBLY

Hide 15.INSTALL COMBINATION METER ASSEMBLY

Hide 16.CHECK FLUID LEVEL IN RESERVOIR