Home › Drivetrain › AXLE AND DIFFERENTIAL › FRONT AXLE HUB BOLT › from 2012.10
RM1840EF _52 Drivetrain _009618 AXLE AND DIFFERENTIAL _0052555 FRONT AXLE HUB BOLT A

AXLE AND DIFFERENTIAL  FRONT AXLE HUB BOLT  REPLACEMENT  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.REMOVE FRONT WHEEL

Hide 2.DRAIN BRAKE FLUID (for 2WD)

NOTICE:

Wash off brake fluid immediately if it comes in contact with any painted surface.


Hide 3.DISCONNECT FRONT FLEXIBLE HOSE (for 2WD)

a.
C111360

Remove the union bolt and gasket.


b.

Disconnect the flexible hose from the brake cylinder.


Hide 4.REMOVE FRONT DISC BRAKE CYLINDER ASSEMBLY LH (for 2WD)

F049868

a.

Remove the 2 bolts and disc brake cylinder.


Hide 5.REMOVE FRONT DISC BRAKE CYLINDER ASSEMBLY LH (for 4WD and Pre-Runner)

F042731

a.

Remove the bolt and brake tube bracket from the steering knuckle.


b.
C111186

Remove the 2 bolts and disc brake cylinder.

NOTICE:

Use wire or an equivalent tool to keep the brake cylinder from hanging down by the front flexible hose.



Hide 6.REMOVE FRONT DISC (for 2WD)

Hide 7.REMOVE FRONT DISC (for 4WD and Pre-Runner)

Hide 8.REMOVE FRONT AXLE HUB BOLT

C281947
0.729,1.354 1.75,1.354 true 1.688,0.781 2.135,0.927 true 0.458,1.271 0.75,1.448 0.292,0.177 10 false SST 1.542,0.698 1.74,0.875 0.198,0.177 10 false *1 2.115,1.813 2.313,1.99 0.198,0.177 10 false *a 2.792,0.885 2.99,1.063 0.198,0.177 10 false *b
*1 Nut
*a Turn
*b Hold


a.

Temporarily install 2 nuts and 2 washers to the front axle hub bolt as shown in the illustration.


b.

Using SST and a screwdriver, remove the hub bolt.

SST
09650-17011  


Hide 9.INSTALL FRONT AXLE HUB BOLT

C281948
0.635,0.896 0.635,0.281 0.635,0.281 0.76,0.281 true 0.948,1.083 0.948,0.813 0.948,0.813 1.073,0.813 false 2.885,0.854 2.885,0.594 2.885,0.594 3.021,0.594 false 2.573,1.01 2.573,1.156 true 0.823,0.188 1.063,0.385 0.24,0.198 10 false *1 1.125,0.698 1.313,0.906 0.188,0.208 10 false *2 2.51,1.177 2.698,1.385 0.188,0.208 10 false *2 3.073,0.49 3.26,0.698 0.188,0.208 10 false *2 2.177,1.906 2.375,2.094 0.198,0.188 10 false *a 3.021,1.313 3.219,1.5 0.198,0.188 10 false *b
*1 Washer
*2 Nut
*a Turn
*b Hold


a.

Temporarily install a plate washer and nut to a new hub bolt as shown in the illustration.


b.

Using a screwdriver to hold the front axle, install a new hub bolt by tightening the nut. Then remove the nut and plate washer.


c.

Remove the 2 nuts from the hub bolts.


Hide 11.INSTALL FRONT DISC (for 4WD and Pre-Runner)

Hide 12.INSTALL FRONT DISC BRAKE CYLINDER ASSEMBLY LH (for 4WD and Pre-Runner)

C111186

a.

Install the disc brake cylinder with the 2 bolts.

Torque:
122 N*m (1244 kgf*cm, 90 ft.*lbf)


b.
F042731

Install the brake tube bracket to the steering knuckle with the bolt.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 13.INSTALL FRONT DISC BRAKE CYLINDER ASSEMBLY LH (for 2WD)

F049868

a.

Install the disc brake cylinder with the 2 bolts.

Torque:
117 N*m (1191 kgf*cm, 86 ft.*lbf)


Hide 14.CONNECT FRONT FLEXIBLE HOSE (for 2WD)

a.
C111360

Install a new gasket and connect the flexible hose with a new union bolt.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)

HINT:

Insert the flexible hose lock securely into the lock hole in the cylinder.



Hide 15.BLEED BRAKE LINE (for 2WD)

Hide 16.INSTALL FRONT WHEEL

Torque:
for 2WD : 152 N*m (1550 kgf*cm, 112 ft.*lbf)
for 4WD and Pre-Runner : 105 N*m (1071 kgf*cm, 77 ft.*lbf)