Home › Drivetrain › AXLE AND DIFFERENTIAL › STEERING KNUCKLE(for 2WD) › from 2012.10
RM1840EF _52 Drivetrain _009618 AXLE AND DIFFERENTIAL _0052570 STEERING KNUCKLE(for 2WD) A

AXLE AND DIFFERENTIAL  STEERING KNUCKLE(for 2WD)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.INSTALL FRONT AXLE HUB INNER BEARING LH

a.
F049862
2.021,1.688 2.938,1.156 2.938,1.156 2,0.74 true 3,1.063 3.417,1.271 0.417,0.208 10 false SST

Using SST and a press, press a new bearing into the steering knuckle.

SST
09527-17011  
09950-60020  (09951-00910)


b.

Using snap ring pliers, install a new snap ring.


Hide 2.INSTALL FRONT AXLE HUB OIL SEAL LH

a.
F049863
2.271,0.75 3.01,1.313 3.01,1.313 2.333,1.771 true 3.094,1.229 3.427,1.438 0.333,0.208 10 false SST

Using SST and a plastic-faced hammer, tap in a new oil seal.

SST
09223-15030  
09527-17011  


b.

Apply MP grease to the lip of the oil seal.


Hide 3.INSTALL STEERING KNUCKLE LH

a.
F049864
1.479,1.125 0.49,1.125 true 0.167,1.021 0.542,1.219 0.375,0.198 10 false SST

Install the dust cover to the steering knuckle with the 3 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 ft.*lbf)


b.

Using SST and a press, press the axle hub into the steering knuckle.

SST
09223-00010  


Hide 4.INSTALL ABS SPEED SENSOR ROTOR (w/ ABS)

a.

Install the ABS speed sensor rotor.


Hide 5.INSTALL FRONT WHEEL INNER BEARING SPACER LH (w/o ABS)

a.

Install the spacer.


Hide 6.INSTALL FRONT AXLE HUB NUT LH

a.
F049769

Install a new nut to the axle hub.

Torque:
199 N*m (2029 kgf*cm, 147 ft.*lbf)


b.

Using a chisel and hammer, stake the nut.

NOTICE:

Do not scratch the serration of the speed sensor rotor.



Hide 7.INSTALL KNUCKLE GREASE RETAINER CAP LH

a.
F049865

Using a brass bar and hammer, install the knuckle grease retainer cap.

NOTICE:

Do not damage the knuckle grease retainer cap.



Hide 8.INSTALL FRONT AXLE HUB ASSEMBLY

a.

Install the front axle hub assembly.


Hide 9.CONNECT FRONT UPPER SUSPENSION ARM ASSEMBLY LH

C113713

a.

Connect the upper arm with the nut.

Torque:
110 N*m (1122 kgf*cm, 81 ft.*lbf)


b.

Install a new clip.

NOTICE:

If the holes for the clip are not aligned, tighten the nut an additional 60°.



Hide 10.CONNECT FRONT LOWER SUSPENSION ARM ASSEMBLY LH

F049765

a.

Connect the suspension arm with the 2 bolts.

Torque:
160 N*m (1632 kgf*cm, 118 ft.*lbf)


Hide 11.CONNECT TIE ROD END SUB-ASSEMBLY LH

C113714

a.

Connect the tie rod end with the nut.

Torque:
49 N*m (500 kgf*cm, 36 ft.*lbf)


b.

Install a new cotter pin.

NOTICE:

If the holes for the cotter pin are not aligned, tighten the nut an additional 60°.



Hide 13.INSTALL FRONT DISC BRAKE CYLINDER ASSEMBLY LH

a.
F049868

Install the brake cylinder with the 2 bolts.

Torque:
117 N*m (1191 kgf*cm, 86 ft.*lbf)


Hide 15.INSTALL FRONT SPEED SENSOR LH (w/ ABS)

C113712

a.

Install the speed sensor with the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


b.

Connect the 3 clamps with the 3 bolts.

Torque:
32 N*m (326 kgf*cm, 24 ft.*lbf)


Hide 17.INSTALL FRONT WHEEL

Torque:
152 N*m (1550 kgf*cm, 112 ft.*lbf)