Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2011.10–2012.01
RM1840EF _54 Brake _009623 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0052600 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C0200/31  Front Speed Sensor RH Circuit  C0205/32  Front Speed Sensor LH Circuit  C1235/35  Foreign Object is Attached on Tip of Front Speed Sensor RH  C1236/36  Foreign Object is Attached on Tip of Front Speed Sensor LH  C1271/71  Low Output Signal of Front Speed Sensor RH (Test Mode DTC)  C1272/72  Low Output Signal of Front Speed Sensor LH (Test Mode DTC)  C1275/75  Abnormal Change in Output Signal of Front Speed Sensor RH (Test Mode DTC)  C1276/76  Abnormal Change in Output Signal of Front Speed Sensor LH (Test Mode DTC)  


DESCRIPTION

The speed sensors detect the wheel speeds and send appropriate signals to the skid control ECU (brake actuator assembly). These signals are used for control of the ABS.

Each of the front and rear rotors have 48 serrations. When the rotors rotate, the magnetic field generated by the permanent magnet in the speed sensor produces AC voltage. Since the frequency of this AC voltage changes in direct proportion to the speed of the rotor, the frequency is used by the skid control ECU (brake actuator assembly) to detect the speed of each wheel.

C238766
4.906,1.188 4.313,0.583 4.313,0.583 4.188,0.583 false 6.146,1.313 6.135,0.49 6.135,0.49 6.229,0.49 false 2.031,1.594 2.167,1.76 0.135,0.167 10 N 2.469,1.594 2.594,1.76 0.125,0.167 10 S 0.135,1.302 0.594,1.5 0.458,0.198 10 Rotor 1.5,1.188 2.646,1.406 1.146,0.219 10 Speed Sensor 2.792,1.583 3.365,1.781 0.573,0.198 10 Magnet 2.823,2.156 3.469,2.354 0.646,0.198 10 to ECU 1.375,1.813 1.729,2.021 0.354,0.208 10 Coil 4.198,1.063 4.448,1.25 0.25,0.188 10 +V 4.219,1.833 4.427,2.031 0.208,0.198 10 -V 3.438,0.5 4.427,0.698 0.99,0.198 10 High Speed 6.26,0.396 7.052,0.594 0.792,0.198 10 Low Speed

DTC No. Detection Item DTC Detection Condition Trouble Area
C0200/31 Front Speed Sensor RH Circuit One of the following conditions is met:
1.

At a vehicle speed of 10 km/h (6 mph) or more, an open or short in the sensor signal circuit continues for 15 seconds or more.

2.

Momentary interruption of the sensor signal from the abnormal wheel occurs 7 times or more.

3.

An open in the speed sensor signal circuit continues for 0.5 seconds or more.


·

Front speed sensor RH

·

Front speed sensor circuit

·

Front skid control rotor RH

·

Sensor installation

·

Skid control ECU (Brake actuator assembly)


C0205/32 Front Speed Sensor LH Circuit One of the following conditions is met:
1.

At a vehicle speed of 10 km/h (6 mph) or more, an open or short in the sensor signal circuit continues for 15 seconds or more.

2.

Momentary interruption of the sensor signal from the abnormal wheel occurs 7 times or more.

3.

An open in the speed sensor signal circuit continues for 0.5 seconds or more.


·

Front speed sensor LH

·

Front speed sensor circuit

·

Front skid control rotor LH

·

Sensor installation

·

Skid control ECU (Brake actuator assembly)


C1235/35 Foreign Object is Attached on Tip of Front Speed Sensor RH At a vehicle speed of 20 km/h (12 mph) or more, condition that noise is included in speed sensor signal continues for 5 seconds or more.
·

Front speed sensor RH

·

Front speed sensor circuit

·

Sensor installation


C1236/36 Foreign Object is Attached on Tip of Front Speed Sensor LH At a vehicle speed of 20 km/h (12 mph) or more, condition that noise is included in speed sensor signal continues for 5 seconds or more.
·

Front speed sensor LH

·

Front speed sensor circuit

·

Sensor installation


C1271/71 Low Output Signal of Front Speed Sensor RH (Test Mode DTC) Detected only during Test Mode.
·

Front speed sensor RH

·

Sensor installation

·

Front skid control rotor RH


C1272/72 Low Output Signal of Front Speed Sensor LH (Test Mode DTC) Detected only during Test Mode.
·

Front speed sensor LH

·

Sensor installation

·

Front skid control rotor LH


C1275/75 Abnormal Change in Output Signal of Front Speed Sensor RH (Test Mode DTC) Detected only during Test Mode. Front skid control rotor RH
C1276/76 Abnormal Change in Output Signal of Front Speed Sensor LH (Test Mode DTC) Detected only during Test Mode. Front skid control rotor LH

HINT:
·

DTCs C0200/31, C1235/35, C1271/71 and C1275/75 are for the front speed sensor RH.

·

DTCs C0205/32, C1236/36, C1272/72 and C1276/76 are for the front speed sensor LH.



WIRING DIAGRAM

C149728
0.417,0.771 1.25,1.167 0.833,0.396 10 false Front Speed Sensor RH 0.417,1.958 1.25,2.333 0.833,0.375 10 false Front Speed Sensor LH 5.375,3.125 7,3.583 1.625,0.458 10 false Skid Control ECU (Brake Actuator Assembly) 5.563,0.76 5.958,1.042 0.396,0.281 10 false FR+ 5.552,1.26 5.917,1.49 0.365,0.229 10 false FR- 5.552,2.458 5.927,2.698 0.375,0.24 10 false FL- 5.552,1.979 5.917,2.208 0.365,0.229 10 false FL+ 2.292,1.875 2.385,2.021 0.094,0.146 10 false 1 2.292,1.146 2.385,1.292 0.094,0.146 10 false 2 2.281,0.677 2.375,0.823 0.094,0.146 10 false 1 2.302,2.354 2.396,2.5 0.094,0.146 10 false 2 0.406,1.802 0.771,1.958 0.365,0.156 10 false A12 5.281,0.677 5.573,0.875 0.292,0.198 10 false 31 5.281,1.177 5.542,1.375 0.26,0.198 10 false 30 5.313,2.375 5.5,2.583 0.188,0.208 10 false 8 5.302,1.875 5.5,2.083 0.198,0.208 10 false 9 5.375,2.938 5.917,3.115 0.542,0.177 10 false A13 1.865,0.76 2.25,0.917 0.385,0.156 10 false FR+ 1.885,1.26 2.25,1.417 0.365,0.156 10 false FR- 1.896,1.99 2.25,2.167 0.354,0.177 10 false FL+ 1.906,2.458 2.25,2.667 0.344,0.208 10 false FL- 0.406,0.594 0.781,0.781 0.375,0.188 10 false A11

CAUTION / NOTICE / HINT

NOTICE:
·

Check the speed sensor signal after cleaning or replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE).

·

Before disconnecting the connector, make sure that there are no problems with the connection.

·

After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
a.

Using the intelligent tester, check for any momentary interruptions in the wire harness and connector corresponding to the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>CHECK FOR INTERMITTENT PROBLEMS

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Speed Open Front speed sensor RH open circuit detection Opn_Det or Normal Normal -
FL Speed Open Front speed sensor LH open circuit detection Opn_Det or Normal Normal -
Chassis > ABS/VSC/TRC > Data List
Tester Display
FR Speed Open
FL Speed Open
50003 8 203,201
OK:

Normal (There are no momentary interruptions.)


HINT:

Perform the above inspection before removing the sensor and connector.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING INTELLIGENT TESTER (FR/FL WHEEL SPEED)

NG

5.CHECK THAT SKID CONTROL ECU AND FRONT SPEED SENSOR CONNECTORS ARE SECURELY CONNECTED
2.READ VALUE USING INTELLIGENT TESTER (FR/FL WHEEL SPEED)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Start the engine.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List, and then drive the vehicle.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Wheel Speed Front speed sensor RH reading Min.: 0 km/h (0 mph)
Max.: 326 km/h (202 mph)
Actual wheel speed No large fluctuations when driving at a constant speed.
FL Wheel Speed Front speed sensor LH reading Min.: 0 km/h (0 mph)
Max.: 326 km/h (202 mph)
Actual wheel speed No large fluctuations when driving at a constant speed.
Chassis > ABS/VSC/TRC > Data List
Tester Display
FR Wheel Speed
FL Wheel Speed
50003 8 127,130

f.

Check the speed value output from the speed sensor displayed on the intelligent tester.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire inflation and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>OPERATION CHECK


OK:

The speed value output from the speed sensor displayed on the intelligent tester is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).



Result:
Proceed to
OK
NG



OK

3.PERFORM TEST MODE (SIGNAL CHECK)

NG

7.CHECK FRONT SPEED SENSOR INSTALLATION
3.PERFORM TEST MODE (SIGNAL CHECK)
a.

Perform the sensor check in the Test Mode procedure.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE

OK:

All Test Mode DTCs are cleared.



Result:
Proceed to
OK
NG



OK

4.RECONFIRM DTC

NG

7.CHECK FRONT SPEED SENSOR INSTALLATION
4.RECONFIRM DTC
a.

Clear the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 8

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 8
Result:
Result Proceed to
DTC not output A
DTC output B


HINT:

If troubleshooting has been carried out according to the problem symptoms table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE




A

B

12.REPLACE FRONT SPEED SENSOR
5.CHECK THAT SKID CONTROL ECU AND FRONT SPEED SENSOR CONNECTORS ARE SECURELY CONNECTED
a.

Check that the skid control ECU (brake actuator assembly) and the front speed sensor connectors are securely connected.


Result:
Proceed to
NEXT



NEXT

6.RECONFIRM DTC
6.RECONFIRM DTC
a.

Clear the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 8

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 8
Result:
Result Proceed to
DTC output A
DTC not output B




A

7.CHECK FRONT SPEED SENSOR INSTALLATION

B

7.CHECK FRONT SPEED SENSOR INSTALLATION
a.

Turn the ignition switch off.


b.
C108871
0.833,1.625 0.74,1.385 false 0.063,0.073 0.375,0.229 0.313,0.156 10 *1 0.885,1.583 1.198,1.74 0.313,0.156 10 *a 0.417,1.76 0.729,1.917 0.313,0.156 10 *b 2.729,1.833 3.042,1.99 0.313,0.156 10 *c
*1 Front Speed Sensor
*a No clearance
*b CORRECT
*c INCORRECT


Check the speed sensor installation.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR(for 4WD and Pre-Runner)>INSPECTION

OK:

There is no clearance between the sensor and the steering knuckle.

The installation bolt is tightened properly.



Result:
Proceed to
OK
NG



OK

8.INSPECT FRONT SPEED SENSOR TIP

NG

INSTALL FRONT SPEED SENSOR CORRECTLY

8.INSPECT FRONT SPEED SENSOR TIP
a.

Turn the ignition switch off.



c.

Check the speed sensor tip.

OK:

No scratches, oil or foreign matter on the sensor tip.


NOTICE:

Do not replace the speed sensor if no damage to the speed sensor tip is found.


HINT:
·

If the sensor is contaminated with oil or other foreign material, clean the sensor.

·

If there is iron powder sticking to the rotor, this will result in a malfunction. Confirm that the rotor is not contaminated with foreign material before replacing the sensor.




Result:
Proceed to
OK
NG



OK

9.INSPECT FRONT SPEED SENSOR

NG

CLEAN OR REPLACE FRONT SPEED SENSOR

9.INSPECT FRONT SPEED SENSOR
a.

Turn the ignition switch off.




Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR)

NG

REPLACE FRONT SPEED SENSOR

10.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR)
a.

Turn the ignition switch off.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.

Disconnect the front speed sensor connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LH
Tester Connection Condition Specified Condition
A13-9 (FL+) - A12-1 (FL+) Always Below 1 Ω
A13-9 (FL+) - Body ground Always 10 kΩ or higher
A13-8 (FL-) - A12-2 (FL-) Always Below 1 Ω
A13-8 (FL-) - Body ground Always 10 kΩ or higher

for RH
Tester Connection Condition Specified Condition
A13-31 (FR+) - A11-1 (FR+) Always Below 1 Ω
A13-31 (FR+) - Body ground Always 10 kΩ or higher
A13-30 (FR-) - A11-2 (FR-) Always Below 1 Ω
A13-30 (FR-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.INSPECT FRONT SKID CONTROL ROTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.INSPECT FRONT SKID CONTROL ROTOR
a.

Turn the ignition switch off.



c.

Check the front skid control rotor.

OK:

No scratches, oil or foreign matter on the rotors.



Result:
Proceed to
OK
NG



OK

12.REPLACE FRONT SPEED SENSOR

NG

CLEAN OR REPLACE FRONT SKID CONTROL ROTOR

12.REPLACE FRONT SPEED SENSOR
a.

Turn the ignition switch off.



Result:
Proceed to
NEXT



NEXT

13.RECONFIRM DTC
13.RECONFIRM DTC
a.

Clear the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 8

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 8
Result:
Result Proceed to
DTC output A
DTC not output B




A

B

END