Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2011.10–2012.01
RM1840EF _54 Brake _009623 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0052600 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C0210/33  Rear Speed Sensor RH Circuit  C0215/34  Rear Speed Sensor LH Circuit  C1238/38  Foreign Object is Attached on Tip of Rear Speed Sensor RH  C1239/39  Foreign Object is Attached on Tip of Rear Speed Sensor LH  C1273/73  Low Output Signal of Rear Speed Sensor RH (Test Mode DTC)  C1274/74  Low Output Signal of Rear Speed Sensor LH (Test Mode DTC)  C1277/77  Abnormal Change in Output Signal of Rear Speed Sensor RH (Test Mode DTC)  C1278/78  Abnormal Change in Output Signal of Rear Speed Sensor LH (Test Mode DTC)  


DESCRIPTION

The speed sensors detect the wheel speeds and send appropriate signals to the skid control ECU (brake actuator assembly). These signals are used for control of the ABS.

Each of the front and rear rotors have 48 serrations. When the rotors rotate, the magnetic field generated by the permanent magnet in the speed sensor produces AC voltage. Since the frequency of this AC voltage changes in direct proportion to the speed of the rotor, the frequency is used by the skid control ECU (brake actuator assembly) to detect the speed of each wheel.

C238766
4.906,1.188 4.313,0.583 4.313,0.583 4.188,0.583 false 6.146,1.323 6.135,0.5 6.135,0.5 6.229,0.5 false 2.052,1.594 2.188,1.76 0.135,0.167 10 N 2.479,1.594 2.604,1.76 0.125,0.167 10 S 0.135,1.229 0.594,1.427 0.458,0.198 10 Rotor 1.5,1.188 2.646,1.406 1.146,0.219 10 Speed Sensor 2.792,1.573 3.365,1.771 0.573,0.198 10 Magnet 2.823,2.156 3.469,2.354 0.646,0.198 10 to ECU 1.375,1.813 1.729,2.021 0.354,0.208 10 Coil 4.198,1.063 4.448,1.25 0.25,0.188 10 +V 4.219,1.833 4.427,2.031 0.208,0.198 10 -V 3.438,0.5 4.427,0.698 0.99,0.198 10 High Speed 6.292,0.417 7.083,0.615 0.792,0.198 10 Low Speed

DTC No. Detection Item DTC Detection Condition Trouble Area
C0210/33 Rear Speed Sensor RH Circuit One of the following conditions is met:
1.

At a vehicle speed of 10 km/h (6 mph) or more, an open or short in the sensor signal circuit continues for 15 seconds or more.

2.

Momentary interruption of the sensor signal from the abnormal wheel occurs 7 times or more.

3.

An open in the speed sensor signal circuit continues for 0.5 seconds or more.


·

Rear speed sensor RH

·

Rear speed sensor circuit

·

Rear skid control rotor RH

·

Sensor installation

·

Skid control ECU (Brake actuator assembly)


C0215/34 Rear Speed Sensor LH Circuit One of the following conditions is met:
1.

At a vehicle speed of 10 km/h (6 mph) or more, an open or short in the sensor signal circuit continues for 15 seconds or more.

2.

Momentary interruption of the sensor signal from the abnormal wheel occurs 7 times or more.

3.

An open in the speed sensor signal circuit continues for 0.5 seconds or more.


·

Rear speed sensor LH

·

Rear speed sensor circuit

·

Rear skid control rotor LH

·

Sensor installation

·

Skid control ECU (Brake actuator assembly)


C1238/38 Foreign Object is Attached on Tip of Rear Speed Sensor RH At a vehicle speed of 20 km/h (12 mph) or more, condition that noise is included in speed sensor signal continues for 5 seconds or more.
·

Rear speed sensor RH

·

Rear speed sensor circuit

·

Sensor installation


C1239/39 Foreign Object is Attached on Tip of Rear Speed Sensor LH At a vehicle speed of 20 km/h (12 mph) or more, condition that noise is included in speed sensor signal continues for 5 seconds or more.
·

Rear speed sensor LH

·

Rear speed sensor circuit

·

Sensor installation


C1273/73 Low Output Signal of Rear Speed Sensor RH (Test Mode DTC) Detected only during Test Mode.
·

Rear speed sensor RH

·

Sensor installation

·

Rear skid control rotor RH


C1274/74 Low Output Signal of Rear Speed Sensor LH (Test Mode DTC) Detected only during Test Mode.
·

Rear speed sensor LH

·

Sensor installation

·

Rear skid control rotor LH


C1277/77 Abnormal Change in Output Signal of Rear Speed Sensor RH (Test Mode DTC) Detected only during Test Mode. Rear skid control rotor RH/LH
C1278/78 Abnormal Change in Output Signal of Rear Speed Sensor LH (Test Mode DTC) Detected only during Test Mode. Rear skid control rotor RH/LH

HINT:
·

DTCs C0210/33, C1238/38, C1273/73 and C1277/77 are for the rear speed sensor RH.

·

DTCs C0215/34, C1239/39, C1274/74 and C1278/78 are for the rear speed sensor LH.



WIRING DIAGRAM

C241007
0.416,0.724 1.2,1.034 0.785,0.311 10 Rear Speed Sensor RH 0.416,1.914 1.203,2.23 0.787,0.315 10 Rear Speed Sensor LH 5.392,3.038 7.004,3.435 1.612,0.397 10 Skid Control ECU (Brake Actuator Assembly) 5.548,0.712 5.866,0.856 0.318,0.143 10 RR+ 5.547,1.204 5.871,1.344 0.324,0.141 10 RR- 5.554,2.41 5.808,2.553 0.253,0.142 10 RL- 5.553,1.923 5.838,2.069 0.285,0.146 10 RL+ 2.325,2.305 2.423,2.452 0.098,0.148 10 1 2.325,0.614 2.423,0.765 0.098,0.15 10 2 2.328,1.076 2.423,1.225 0.095,0.148 10 1 2.325,1.809 2.423,1.959 0.098,0.15 10 2 0.416,0.557 0.755,0.714 0.339,0.157 10 L7 0.416,1.756 0.735,1.913 0.319,0.157 10 L3 5.312,0.607 5.486,0.756 0.173,0.149 10 33 5.312,1.097 5.488,1.246 0.175,0.149 10 34 5.312,2.32 5.496,2.462 0.184,0.142 10 12 5.312,1.839 5.496,1.985 0.184,0.146 10 11 5.392,2.89 5.77,3.071 0.378,0.182 10 A13

CAUTION / NOTICE / HINT

NOTICE:
·

Check the speed sensor signal after cleaning or replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE).

·

Before disconnecting the connector, make sure that there are no problems with the connection.

·

After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
a.

Using the intelligent tester, check for any momentary interruptions in the wire harness and connector corresponding to the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>CHECK FOR INTERMITTENT PROBLEMS

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Speed Open Rear speed sensor RH open circuit detection Opn_Det or Normal Normal -
RL Speed Open Rear speed sensor LH open circuit detection Opn_Det or Normal Normal -
Chassis > ABS/VSC/TRC > Data List
Tester Display
RR Speed Open
RL Speed Open
50003 8 199,197
OK:

Normal (There are no momentary interruptions.)


HINT:

Perform the above inspection before removing the sensor and connector.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING INTELLIGENT TESTER (RR/RL WHEEL SPEED)

NG

5.CHECK THAT SKID CONTROL ECU AND REAR SPEED SENSOR CONNECTORS ARE SECURELY CONNECTED
2.READ VALUE USING INTELLIGENT TESTER (RR/RL WHEEL SPEED)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the intelligent tester on.


d.

Start the engine.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List, and then drive the vehicle.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Wheel Speed Rear speed sensor RH reading Min.: 0 km/h (0 mph)
Max.: 326 km/h (202 mph)
Actual wheel speed No large fluctuations when driving at a constant speed.
RL Wheel Speed Rear speed sensor LH reading Min.: 0 km/h (0 mph)
Max.: 326 km/h (202 mph)
Actual wheel speed No large fluctuations when driving at a constant speed.
Chassis > ABS/VSC/TRC > Data List
Tester Display
RR Wheel Speed
RL Wheel Speed
50003 8 131,134

f.

Check the speed value output from the speed sensor displayed on the intelligent tester.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire inflation and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>OPERATION CHECK


OK:

The speed value output from the speed sensor displayed on the intelligent tester is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).



Result:
Proceed to
OK
NG



OK

3.PERFORM TEST MODE (SIGNAL CHECK)

NG

7.CHECK REAR SPEED SENSOR INSTALLATION
3.PERFORM TEST MODE (SIGNAL CHECK)
a.

Perform the sensor check in the Test Mode procedure.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE

OK:

All Test Mode DTCs are cleared.



Result:
Proceed to
OK
NG



OK

4.RECONFIRM DTC

NG

7.CHECK REAR SPEED SENSOR INSTALLATION
4.RECONFIRM DTC
a.

Clear the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 8

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 8
Result:
Result Proceed to
DTC not output A
DTC output B


HINT:

If troubleshooting has been carried out according to the problem symptoms table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE




A

B

12.REPLACE REAR SPEED SENSOR
5.CHECK THAT SKID CONTROL ECU AND REAR SPEED SENSOR CONNECTORS ARE SECURELY CONNECTED
a.

Check that the skid control ECU (brake actuator assembly) and the rear speed sensor connectors are securely connected.


Result:
Proceed to
NEXT



NEXT

6.RECONFIRM DTC
6.RECONFIRM DTC
a.

Clear the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 8

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 8
Result:
Result Proceed to
DTC output A
DTC not output B




A

7.CHECK REAR SPEED SENSOR INSTALLATION

B

7.CHECK REAR SPEED SENSOR INSTALLATION
a.

Turn the ignition switch off.


b.
C108871
0.833,1.625 0.74,1.385 false 0.063,0.073 0.375,0.229 0.313,0.156 10 *1 0.885,1.583 1.198,1.74 0.313,0.156 10 *a 0.417,1.76 0.729,1.917 0.313,0.156 10 *b 2.729,1.833 3.042,1.99 0.313,0.156 10 *c
*1 Rear Speed Sensor
*a No clearance
*b CORRECT
*c INCORRECT


Check the rear speed sensor installation.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR>INSPECTION

OK:

The installation bolt is tightened properly.

There is no clearance between the sensor and rear axle housing.



Result:
Proceed to
OK
NG



OK

8.INSPECT REAR SPEED SENSOR TIP

NG

INSTALL REAR SPEED SENSOR CORRECTLY

8.INSPECT REAR SPEED SENSOR TIP
a.

Turn the ignition switch off.



c.

Check the speed sensor tip.

OK:

No scratches, oil or foreign matter on the sensor tip.


NOTICE:

Do not replace the speed sensor if no damage to the speed sensor tip is found.


HINT:
·

If the sensor is contaminated with oil or other foreign material, clean the sensor.

·

If there is iron powder sticking to the rotor, this will result in a malfunction. Confirm that the rotor is not contaminated with foreign material before replacing the sensor.




Result:
Proceed to
OK
NG



OK

9.INSPECT REAR SPEED SENSOR

NG

CLEAN OR REPLACE REAR SPEED SENSOR

9.INSPECT REAR SPEED SENSOR
a.

Turn the ignition switch off.




Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - REAR SPEED SENSOR)

NG

10.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - REAR SPEED SENSOR)
a.

Turn the ignition switch off.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.

Disconnect the rear speed sensor connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LH
Tester Connection Condition Specified Condition
A13-11 (RL+) - L3-2 Always Below 1 Ω
A13-11 (RL+) - Body ground Always 10 kΩ or higher
A13-12 (RL-) - L3-1 Always Below 1 Ω
A13-12 (RL-) - Body ground Always 10 kΩ or higher

for RH
Tester Connection Condition Specified Condition
A13-33 (RR+) - L7-2 Always Below 1 Ω
A13-33 (RR+) - Body ground Always 10 kΩ or higher
A13-34 (RR-) - L7-1 Always Below 1 Ω
A13-34 (RR-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.INSPECT REAR SKID CONTROL ROTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.INSPECT REAR SKID CONTROL ROTOR
a.

Turn the ignition switch off.


b.

Remove the rear axle shaft with backing plate.

Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE SHAFT>REMOVAL


c.

Check the rear skid control rotor.

OK:

No scratches, oil or foreign matter on the rotors.



Result:
Proceed to
OK
NG



OK

12.REPLACE REAR SPEED SENSOR

NG

CLEAN OR REPLACE REAR SKID CONTROL ROTOR

12.REPLACE REAR SPEED SENSOR
a.

Turn the ignition switch off.



Result:
Proceed to
NEXT



NEXT

13.CONFIRM DTC
13.CONFIRM DTC
a.

Clear the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 8

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 8
Result:
Result Proceed to
DTC output A
DTC not output B




A

B

END