Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2011.10–2012.01
RM1840EF _54 Brake _009623 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0052601 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  VSC OFF Indicator Light Remains ON  


DESCRIPTION

If the skid control ECU (brake actuator assembly) stores a DTC, the VSC OFF indicator light blinks in the combination meter.

Pressing the VSC OFF switch turns off traction control and pressing and holding this switch turns off traction control and VSC. If VSC turns off, the VSC OFF indicator light will come on.

When the transfer position is L4, VSC is prohibited and the VSC OFF indicator and slip indicator lights turn on.

WIRING DIAGRAM

C246482
0.24,1.594 1.208,1.833 0.969,0.24 10 false from IG Circuit 0.417,4.365 1.5,4.729 1.083,0.365 10 false from IG Circuit 3.25,1.156 3.906,1.323 0.656,0.167 10 false VSC OFF 3.458,1.781 3.76,1.948 0.302,0.167 10 false Slip 1.719,1.396 1.917,1.563 0.198,0.167 10 false 21 1.667,1.604 1.979,1.771 0.313,0.167 10 false G19 4.5,1.594 4.865,1.823 0.365,0.229 10 false G20 4.51,0.958 5.021,1.292 0.51,0.333 10 false G20 2.292,3.063 2.427,3.229 0.135,0.167 10 false 4 3.479,3.063 3.615,3.229 0.135,0.167 10 false 3 4.563,0.75 4.854,1 0.292,0.25 10 false 16 5.417,0.813 5.74,1.125 0.323,0.313 10 false 15 5.417,3.063 5.615,3.229 0.198,0.167 10 false 30 5.417,4.219 5.615,4.385 0.198,0.167 10 false 34 5.417,5.458 5.615,5.625 0.198,0.167 10 false 28 5.469,1.458 5.615,1.625 0.146,0.167 10 false 3 5.469,2.271 5.615,2.438 0.146,0.167 10 false 1 4.563,1.385 4.875,1.615 0.313,0.229 10 false 17 2.479,2.115 4.375,2.365 1.896,0.25 10 false Combination Meter Assembly 2.51,3.458 2.927,3.625 0.417,0.167 10 false G84 2.51,3.615 3.792,3.854 1.281,0.24 10 false VSC OFF Switch 5.406,6.083 5.833,6.344 0.427,0.26 10 false A36 5.406,6.26 6.979,6.656 1.573,0.396 10 false Skid Control ECU (Brake Actuator Assembly) 2.219,4.552 3.573,4.896 1.354,0.344 10 false ECU-IG&GAUGE 5.698,0.948 6.281,1.26 0.583,0.313 10 false VSCW 5.698,1.583 6.24,1.823 0.542,0.24 10 false IND 5.698,5.552 6.188,5.854 0.49,0.302 10 false EXI3 5.698,3.177 6.24,3.5 0.542,0.323 10 false CSW 5.698,4.375 6.125,4.719 0.427,0.344 10 false IG1 5.698,2.396 6.271,2.635 0.573,0.24 10 false GND1 4,0.844 4.49,1.125 0.49,0.281 10 false TROF 4.073,1.469 4.479,1.74 0.406,0.271 10 false SLIP 2.052,1.5 2.313,1.667 0.26,0.167 10 false IG+ 2.063,5.552 3.271,6.073 1.208,0.521 10 false from IG Circuit

CAUTION / NOTICE / HINT

NOTICE:
·

As there may be malfunctions in the transfer system related to when the transfer operates in L4, check the transfer system first (See page Drivetrain>VF2A TRANSFER / 4WD / AWD>TRANSFER SYSTEM>ON-VEHICLE INSPECTION).

·

After replacing the brake actuator assembly, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).

·

Before disconnecting the connector, make sure that there are no problems with the connection.

·

After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.



PROCEDURE

1.CHECK FOR DTC
a.

Check if DTCs for the VSC are output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DIAGNOSTIC TROUBLE CODE CHART

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTC is not output A
DTC is output B




A

2.READ VALUE USING INTELLIGENT TESTER (TRC/VSC OFF MODE)

B

2.READ VALUE USING INTELLIGENT TESTER (TRC/VSC OFF MODE)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
TRC/VSC Off Mode VSC OFF switch Normal, Unknown, TRC OFF or VSC OFF Normal: Normal mode
TRC OFF: TRC off mode
VSC OFF: VSC off mode
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
TRC/VSC Off Mode
50003 105 282

f.

Check that the mode display changes according to VSC OFF switch operation.

OK:

The intelligent tester display changes according to VSC OFF switch operation.



Result:
Proceed to
OK
NG



OK

3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (VSC WARNING LIGHT)

NG

4.INSPECT VSC OFF SWITCH
3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (VSC WARNING LIGHT)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
VSC Warning Light VSC OFF indicator light Indicator light ON / OFF Observe the combination meter.
Chassis > ABS/VSC/TRC > Active Test
Tester Display
VSC Warning Light
50004 105 9

f.

When performing the VSC Warning Light Active Test, check VSC Warning Light in the Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
VSC Warning Light VSC OFF indicator light ON or OFF ON: VSC OFF indicator light on
OFF: VSC OFF indicator light off
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
VSC Warning Light
50003 105 56
Result:
Result Proceed to
Data List Display Data List Display When Performing Active Test ON/OFF Operation
ON Does not change between ON and OFF A
Changes between ON and OFF B
OFF Does not change between ON and OFF A
Changes between ON and OFF B




A

B

7.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - COMBINATION METER)
4.INSPECT VSC OFF SWITCH
a.

Turn the ignition switch off.




Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - VSC OFF SWITCH)

NG

5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - VSC OFF SWITCH)
a.

Turn the ignition switch off.


b.

Disconnect the VSC OFF switch connector.


c.

Disconnect the skid control ECU (brake actuator assembly) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A36-30 (CSW) - G84-3 Always Below 1 Ω
A36-30 (CSW) - Body ground Always 10 kΩ or higher
G84-4 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK TERMINAL VOLTAGE (EXI3 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK TERMINAL VOLTAGE (EXI3 TERMINAL)
a.

Turn the ignition switch off.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.
C199357
0.167,0.969 0.5,1.188 0.333,0.219 1.906,1.969 1.802,1.969 1.802,1.969 1.635,1.385 false 0.094,0.094 0.406,0.25 0.313,0.156 10 false *a 0.219,1 0.625,1.26 0.406,0.26 10 false A36 1.948,1.896 2.323,2.125 0.375,0.229 10 false EXI3
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A36-28 (EXI3) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - COMBINATION METER)
a.

Turn the ignition switch off.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.

Disconnect the G20 combination meter connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A36-15 (VSCW) - G20-16 (TROF) Always Below 1 Ω
A36-15 (VSCW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR