Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2011.10–2012.01
RM1840EF _54 Brake _009623 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0052601 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  VSC OFF Indicator Light does not Come ON  


CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the brake actuator assembly, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).

·

Before disconnecting the connector, make sure that there are no problems with the connection.

·

After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.



PROCEDURE

1.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU (brake actuator assembly) connector is securely connected.

OK:

The connector is securely connected.



Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (IG1 TERMINAL)

NG

CONNECT CONNECTOR TO ECU CORRECTLY

2.CHECK TERMINAL VOLTAGE (IG1 TERMINAL)
a.

Turn the ignition switch off.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.
C199357
0.188,0.99 0.51,1.208 0.323,0.219 2.073,1.927 2.146,1.927 2.146,1.927 2.302,1.396 false 0.083,0.083 0.396,0.24 0.313,0.156 10 false *a 0.229,1.021 0.542,1.271 0.313,0.25 10 false A36 1.833,1.844 2.146,2.094 0.313,0.25 10 false IG1
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A36-34 (IG1) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
a.

Turn the ignition switch off.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A36-1 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT VSC OFF SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT VSC OFF SWITCH
a.

Turn the ignition switch off.




Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - VSC OFF SWITCH)

NG

5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - VSC OFF SWITCH)
a.

Turn the ignition switch off.


b.

Disconnect the VSC OFF switch connector.


c.

Disconnect the skid control ECU (brake actuator assembly) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A36-30 (CSW) - G84-3 Always Below 1 Ω
A36-30 (CSW) - Body ground Always 10 kΩ or higher
G84-4 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - COMBINATION METER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - COMBINATION METER)
a.

Turn the ignition switch off.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.

Disconnect the G20 combination meter connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A36-15 (VSCW) - G20-16 (TROF) Always Below 1 Ω
A36-15 (VSCW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (VSC WARNING LIGHT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (VSC WARNING LIGHT)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
VSC Warning Light VSC OFF indicator light Indicator light ON / OFF Observe the combination meter.
Chassis > ABS/VSC/TRC > Active Test
Tester Display
VSC Warning Light
50004 105 9

f.

When performing the VSC Warning Light Active Test, check VSC Warning Light in the Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
VSC Warning Light VSC OFF indicator light ON or OFF ON: VSC OFF indicator light on
OFF: VSC OFF indicator light off
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
VSC Warning Light
50003 105 56
Result:
Result Proceed to
Data List Display Data List Display When Performing Active Test ON/OFF Operation
ON Does not change between ON and OFF A
Changes between ON and OFF B
OFF Does not change between ON and OFF A
Changes between ON and OFF B




A

B

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)