Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2011.10–2012.01
RM1840EF _54 Brake _009623 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0052601 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1401  Front Speed Sensor RH Malfunction  C1271  Low Output Signal of Front Speed Sensor RH (Test Mode DTC)  C1272  Low Output Signal of Front Speed Sensor LH (Test Mode DTC)  C1402  Front Speed Sensor LH Malfunction  


DESCRIPTION

The speed sensors detect the wheel speeds and send appropriate signals to the skid control ECU (brake actuator assembly). The speed sensor has a magnet behind its detection terminal, and detects changes in magnetic flux density between the peaks and valleys of the magnetic rotor teeth.

The speed sensors detect those magnetic changes and send pulse signals to the skid control ECU (brake actuator assembly). The ECU monitors the wheel speeds through these pulse signals to control the brake control system.

HINT:

When the connectors between the speed sensor and skid control ECU (brake actuator assembly) are connected, the following waveform is output.


C238408
1.365,0.25 1.625,0.813 false 5.188,1.823 6.135,2.135 0.948,0.313 10 false High Speed 4.25,1.823 5.188,2.115 0.938,0.292 10 false Low Speed 6.323,1.354 6.958,1.667 0.635,0.313 10 false 0.7 V 6.323,0.99 6.823,1.302 0.5,0.313 10 false 1.4 V 0.469,0.135 1.5,0.385 1.031,0.25 10 false Speed Sensor 1.063,2.083 2.646,2.531 1.583,0.448 10 false Speed Sensor Rotor 4.115,0.344 5.667,0.635 1.552,0.292 10 false Waveform (Reference): 4.115,0.635 7.021,0.938 2.906,0.302 10 false Between Speed Sensor (-) and Body Ground

DTC No. Detection Item DTC Detection Condition Trouble Area
C1271 Low Output Signal of Front Speed Sensor RH (Test Mode DTC) Stored during Test Mode.
·

Front speed sensor RH

·

Front skid control rotor RH

·

Sensor installation


C1272 Low Output Signal of Front Speed Sensor LH (Test Mode DTC) Stored during Test Mode.
·

Front speed sensor LH

·

Front skid control rotor LH

·

Sensor installation


C1401 Front Speed Sensor RH Malfunction One of the following conditions is met:
1.

At a vehicle speed of 10 km/h (6 mph) or more, the output voltage from one of the speed sensors is below that of the other sensors for 15 seconds or more.

2.

At a vehicle speed of less than 10 km/h (6 mph), the output from one of the speed sensors is 0 km/h (0 mph) for 1 second or more.

3.

At a vehicle speed of 10 km/h (6 mph) or more, the outputs from both front speed sensors are 0 km/h (0 mph) for 15 seconds or more.


·

Front speed sensor RH

·

Front skid control rotor RH

·

Sensor installation


C1402 Front Speed Sensor LH Malfunction One of the following conditions is met:
1.

At a vehicle speed of 10 km/h (6 mph) or more, the output voltage from one of the speed sensors is below that of the other sensors for 15 seconds or more.

2.

At a vehicle speed of less than 10 km/h (6 mph), the output from one of the speed sensors is 0 km/h (0 mph) for 1 second or more.

3.

At a vehicle speed of 10 km/h (6 mph) or more, the outputs from both front speed sensors are 0 km/h (0 mph) for 15 seconds or more.


·

Front speed sensor LH

·

Front skid control rotor LH

·

Sensor installation



HINT:
·

DTCs C1401 and C1271 are for the front speed sensor RH.

·

DTCs C1402 and C1272 are for the front speed sensor LH.



CAUTION / NOTICE / HINT

NOTICE:

Check the speed sensor signal after cleaning or replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).


PROCEDURE

1.CHECK FRONT SPEED SENSOR INSTALLATION
a.

Turn the ignition switch off.


b.
C108871
0.698,1.375 0.875,1.635 false 0.083,0.063 0.396,0.219 0.313,0.156 10 false *1 0.917,1.594 1.229,1.75 0.313,0.156 10 false *a 0.458,1.792 0.771,1.948 0.313,0.156 10 false *b 2.729,1.854 3.042,2.01 0.313,0.156 10 false *c
*1 Front Speed Sensor
*a No clearance
*b CORRECT
*c INCORRECT


Check the speed sensor installation.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR(for 4WD and Pre-Runner)>INSTALLATION

OK:

There is no clearance between the sensor and the steering knuckle.

The installation bolt is tightened properly.



Result:
Proceed to
OK
NG



OK

2.INSPECT FRONT SPEED SENSOR TIP

NG

2.INSPECT FRONT SPEED SENSOR TIP
a.

Turn the ignition switch off.



c.

Check the speed sensor tip.

OK:

No scratches, oil or foreign matter on the sensor tip.


NOTICE:

Do not replace the speed sensor if no damage to the speed sensor tip is found.


HINT:
·

If the sensor is contaminated with oil or other foreign material, clean the sensor.

·

If there is iron powder sticking to the rotor, this will result in a malfunction. Therefore, confirm that the rotor is not contaminated with foreign material before replacing the sensor.




Result:
Proceed to
OK
NG



OK

3.INSPECT FRONT SKID CONTROL ROTOR

NG

CLEAN OR REPLACE FRONT SPEED SENSOR

3.INSPECT FRONT SKID CONTROL ROTOR
a.

Turn the ignition switch off.



c.

Check the front skid control rotor

OK:

No scratches, oil or foreign matter on the rotor.



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING INTELLIGENT TESTER (FR/FL WHEEL SPEED)

NG

CLEAN OR REPLACE FRONT SKID CONTROL ROTOR

4.READ VALUE USING INTELLIGENT TESTER (FR/FL WHEEL SPEED)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Start the engine.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List, and then drive the vehicle.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Wheel Speed Front speed sensor RH reading Min.: 0 km/h (0 mph)
Max.: 326 km/h (202 mph)
Actual wheel speed No large fluctuations when driving at a constant speed.
FL Wheel Speed Front speed sensor LH reading Min.: 0 km/h (0 mph)
Max.: 326 km/h (202 mph)
Actual wheel speed No large fluctuations when driving at a constant speed.
Chassis > ABS/VSC/TRC > Data List
Tester Display
FR Wheel Speed
FL Wheel Speed
50003 105 1,2

f.

Check the speed value output from the speed sensor displayed on the intelligent tester.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire inflation and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, refer to the reference chart.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>OPERATION CHECK


OK:

The speed value output from the speed sensor displayed on the intelligent tester is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).



Result:
Proceed to
OK
NG



OK

NG

5.REPLACE FRONT SPEED SENSOR
5.REPLACE FRONT SPEED SENSOR
a.

Turn the ignition switch off.



Result:
Proceed to
NEXT



NEXT

6.RECONFIRM DTC
6.RECONFIRM DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTC is not output A
DTC is output B




A

END

B