Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2011.10–2012.01
RM1840EF _54 Brake _009623 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0052601 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1210  Zero Point Calibration of Yaw Rate Sensor Undone  C1336  Zero Point Calibration of Acceleration Sensor Undone  


DESCRIPTION

The skid control ECU (brake actuator assembly) receives signals from the yaw rate sensor assembly via the CAN communication system.

The yaw rate sensor assembly has a built-in acceleration sensor.

If there is trouble in the bus lines between the yaw rate sensor assembly and the CAN communication system, DTCs U0123 (Lost Communication with Yaw Rate Sensor Module) and U0124 (Lost Communication with Lateral Acceleration Sensor Module) are stored.

DTC C1210 and C1336 are also stored when calibration has not been completed.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1210 Zero Point Calibration of Yaw Rate Sensor Undone Zero point calibration of the yaw rate sensor is incomplete.
·

Yaw rate sensor assembly

·

Skid control ECU (Brake actuator assembly)


C1336 Zero Point Calibration of Acceleration Sensor Undone Zero point calibration of the acceleration sensor is incomplete.
·

Acceleration sensor (Yaw rate sensor assembly)

·

Skid control ECU (Brake actuator assembly)



CAUTION / NOTICE / HINT

NOTICE:

After replacing the brake actuator assembly and/or yaw rate sensor assembly, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


HINT:

When DTC U0123 and/or U0124 is output along with DTC C1210 and/or C1336, inspect and repair trouble areas indicated by DTC U0123 and/or U0124 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>U0073).


PROCEDURE

1.PERFORM ZERO POINT CALIBRATION OF YAW RATE AND ACCELERATION SENSOR
a.

Perform zero point calibration of the yaw rate and acceleration sensor.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION


Result:
Proceed to
NEXT



NEXT

2.PERFORM TEST MODE (SIGNAL CHECK)
2.PERFORM TEST MODE (SIGNAL CHECK)
a.

Turn the ignition switch off.


b.

Perform the sensor check in the Test Mode procedure.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE

Chassis > ABS/VSC/TRC > Utility
Tester Display
Signal Check
50005 105 3
OK:

All Test Mode DTCs are cleared.


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next suspected area.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

END

NG

3.CHECK YAW RATE SENSOR ASSEMBLY INSTALLATION
3.CHECK YAW RATE SENSOR ASSEMBLY INSTALLATION
a.

Turn the ignition switch off.


b.

Check that the yaw rate sensor assembly is installed properly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>YAW RATE AND ACCELERATION SENSOR(w/ VSC)>INSTALLATION

OK:

The sensor is tightened to the specified torque.

The sensor is not installed at an angle.



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING INTELLIGENT TESTER (DECELERATION SENSOR / YAW RATE SENSOR)

NG

4.READ VALUE USING INTELLIGENT TESTER (DECELERATION SENSOR / YAW RATE SENSOR)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Deceleration Sensor Acceleration sensor (GL1) Min.: -18.525 m/s2
Max.: 18.387 m/s2
- Changes continuously during acceleration/deceleration.
Deceleration Sensor2 Acceleration sensor (GL2) Min.: -18.525 m/s2
Max.: 18.387 m/s2
- Changes continuously during acceleration/deceleration.
Yaw Rate Sensor Yaw rate sensor Min.: -128°/s
Max.: 127°/s
Vehicle stationary: 0°/s
Right turn: -128 to 0°/s
Left turn: 0 to 127°/s
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
Deceleration Sensor
Deceleration Sensor2
Yaw Rate Sensor
50003 105 14,15,24

f.

Check the yaw rate and acceleration sensor output value displayed on the intelligent tester.

OK:

The yaw rate and acceleration sensor output value is normal.



Result:
Proceed to
OK
NG



OK

NG