Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2011.10–2012.01
RM1840EF _54 Brake _009623 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0052601 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1439  Steering Angle Sensor Initialization Incomplete  C1445  Vehicle Driven with Steering Angle Sensor not Initialized  


DESCRIPTION

The skid control ECU (brake actuator assembly) acquires the steering angle sensor zero point every time the ignition switch is turned to ON and the vehicle is driven at 35 km/h (22 mph) or more for approximately 5 seconds. The ECU also stores the previous zero point.

The steering angle sensor zero point malfunction warning is canceled by turning the ignition switch off.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1439 Steering Angle Sensor Initialization Incomplete After the steering angle sensor zero point calibration is cleared due to, for example, fluctuations in the power source, the steering angle zero point cannot be obtained for 60 seconds of continuous driving.
·

Poor adjustment of centered position of steering wheel

·

Poor adjustment of front wheel alignment

·

Temporary loss of steering angle zero point


C1445 Vehicle Driven with Steering Angle Sensor not Initialized The steering angle sensor zero point cannot be obtained when the vehicle is driven without a record of steering angle sensor zero point calibration at a speed of 36 km/h (22 mph) or more for 30 seconds or more without the brake pedal being depressed.
·

Poor adjustment of centered position of steering wheel

·

Poor adjustment of front wheel alignment

·

Temporary loss of steering angle zero point



CAUTION / NOTICE / HINT

NOTICE:
·

Before proceeding with the inspection, explain to the customer that the output DTC is related to a temporary loss of the steering angle zero point, such as when the power source voltage drops when the battery is removed, and confirm that this condition occurred.

·

After replacing the brake actuator assembly, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).



HINT:
·

When DTC U0073 and/or U0126 is output together with DTC C1439 and/or C1445, inspect and repair the trouble areas indicated by DTC U0073 and/or U0126 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>U0073).

·

When the speed sensor or yaw rate sensor assembly has trouble, DTCs for the steering angle sensor may be stored even when the steering angle sensor is normal. When DTCs for the speed sensor or the yaw rate and acceleration sensor are output together with other DTCs for the steering angle sensor, inspect and repair the speed sensor and yaw rate sensor assembly first, and then inspect and repair the steering angle sensor.



PROCEDURE

1.CHECK DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON again and check that no CAN communication system DTC is output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(w/ VSC)>DIAGNOSIS SYSTEM


d.

Drive the vehicle at a speed of 35 km/h (22 mph) and turn the steering wheel to the right and left, and then check that no speed sensor or yaw rate and acceleration sensor DTCs are output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTC is output C1439 and/or C1445 A
Relating to CAN communication system B
Relating to speed sensor or yaw rate and acceleration sensor C
DTC is not output D


HINT:
·

If there is a malfunction in the speed sensor or yaw rate sensor assembly, an abnormal value may be output although the steering angle sensor is normal.

·

If the speed sensor and the yaw rate and acceleration sensor DTCs are output simultaneously, repair the sensors and inspect the steering angle sensor.

·

If DTC C1439 and/or C1445 is not output again, the DTC may have been stored due to a temporary loss of the steering angle zero point, such as when the power voltage drops.





A

2.PERFORM STEERING ANGLE SENSOR ZERO POINT CALIBRATION

B

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

C

D

2.PERFORM STEERING ANGLE SENSOR ZERO POINT CALIBRATION
a.

Drive the vehicle straight ahead at 35 km/h (22 mph) or more for at least 5 seconds.


b.

Check that the centered position of the steering wheel is correctly set while driving straight ahead.

HINT:

If the front wheel alignment and steering wheel position are adjusted as a result of an abnormal centered position of the steering wheel, acquire the yaw rate sensor zero point again after the adjustments are completed.


OK:

The centered position of the steering wheel is correctly set.



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

ADJUST FRONT WHEEL ALIGNMENT OR STEERING WHEEL POSITION

3.RECONFIRM DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 35 km/h (22 mph) or more and turn the steering wheel to the right and left.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTCs C1439 and C1445 are not output A
Yaw rate and acceleration sensor and/or steering angle sensor DTC is output B


HINT:

If DTC C1439 and/or C1445 is not output again, the DTC may have been stored due to a temporary loss of the steering angle zero point, such as when the power source voltage drops.




A

END

B