Home › Steering › STEERING GEAR / LINKAGE › STEERING GEAR › from 2012.10
RM1840EF _55 Steering _009630 STEERING GEAR / LINKAGE _0052646 STEERING GEAR A

STEERING GEAR / LINKAGE  STEERING GEAR  INSTALLATION  


CAUTION / NOTICE / HINT

PROCEDURE

Hide 1.INSTALL POWER STEERING LINK ASSEMBLY

a.

Install the steering link with the 2 bolts and 2 nuts.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)

HINT:

If necessary, return the differential to its original position and install the differential mount.



Hide 3.CONNECT STEERING GEAR OUTLET RETURN TUBE

a.

Using a union nut wrench, connect the outlet return tube.

Torque:
44 N*m (449 kgf*cm, 33 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



b.

Install the hose with the clip.


Hide 4.CONNECT PRESSURE FEED TUBE ASSEMBLY

a.

Install the pressure feed tube to the steering link with the bolt.

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)


b.

Using a union nut wrench, tighten the flare nut and connect the pressure feed tube.

Torque:
44 N*m (449 kgf*cm, 33 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



Hide 5.CONNECT NO. 2 STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY

a.

Align the matchmarks on the steering intermediate shaft and steering link.


b.

Install the bolt.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)


Hide 6.CONNECT STEERING SLIDING YOKE

a.
C280830C05
1.906,1.833 1.594,1.833 1.594,1.833 1.375,1.198 true 1.708,1.823 1.51,1.063 true 1.938,1.729 2.25,1.885 0.313,0.156 10 false *1 1.323,0.302 1.479,0.5 0.156,0.198 10 false A 0.917,0.854 1.073,1.052 0.156,0.198 10 false B
*1 Matchmark


Align the matchmarks on the steering sliding yoke and steering intermediate shaft, and connect the steering sliding yoke to the steering intermediate shaft.


b.

Install the bolt labeled B.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)


c.

Tighten the bolt labeled A.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)


Hide 7.CONNECT TIE ROD END SUB-ASSEMBLY LH

a.

Connect the tie rod end to the steering knuckle arm with the nut.

Torque:
91 N*m (928 kgf*cm, 67 ft.*lbf)


b.

Install a new cotter pin.

NOTICE:

If the holes for the cotter pin are not aligned, tighten the nut an additional 60°.



Hide 8.CONNECT TIE ROD END SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 9.INSTALL FRONT SIDE MEMBER TO FRONT SUSPENSION CROSSMEMBER BRACE

a.

Install the 2 crossmember braces with the 10 bolts.

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)


Hide 10.INSTALL NO. 1 ENGINE UNDER COVER

a.

Install the under cover with the 4 bolts.

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)


Hide 11.INSTALL NO. 2 ENGINE UNDER COVER

a.

Install the under cover with the 4 bolts.

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)


Hide 13.ADD POWER STEERING FLUID

Hide 15.CHECK POWER STEERING FLUID LEAK