The radio and display receiver assembly receives a reverse signal from the park/neutral position switch assembly*1 or back-up light switch assembly*2.
*1: for Automatic Transmission
*2: for Manual Transmission
Enter the "Function Check/Setting I" mode and select "Vehicle Signal".
Check that the display changes between ON and OFF according to the shift lever position.
| Shift Lever Position | Display |
|---|---|
| R | ON |
| Except R | OFF |
This display is updated once per second. As a result, it is normal for the display to lag behind the actual shift lever position.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Radio and Display Receiver Assembly) |
Disconnect the G127 radio and display receiver assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G127-2 (REV) - Body ground | Ignition switch ON, shift lever in R | 7.5 to 14 V |
| G127-2 (REV) - Body ground | Ignition switch ON, shift lever not in R | Below 1 V |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for Automatic Transmission) | B |
| NG (for Manual Transmission) | C |
A
B
C
Disconnect the G127 radio and display receiver assembly connector.
Disconnect the C26 park/neutral position switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G127-2 (REV) - C26-1 (RL) | Always | Below 1 Ω |
| G127-2 (REV) - Body ground | Always | 10 kΩ or higher |
| Result | Proceed to |
|---|---|
| OK (for A340F) | A |
| OK (for A343E) | B |
| OK (for A343F) | C |
| NG | D |
A
Click hereDrivetrain>A340F AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>REMOVAL
B
Click hereDrivetrain>A343E AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>REMOVAL
C
Click hereDrivetrain>A343F AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>REMOVAL
D
Disconnect the G127 radio and display receiver assembly connector.
Disconnect the C87*1 or C27*2 back-up light switch assembly connector.
*1: for 2TR-FBE
*2: for 1KD-FTV
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G127-2 (REV) - C87-1 | Always | Below 1 Ω |
| G127-2 (REV) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G127-2 (REV) - C27-1 | Always | Below 1 Ω |
| G127-2 (REV) - Body ground | Always | 10 kΩ or higher |
| Result | Proceed to |
|---|---|
| OK (for R151) | A |
| OK (for R151F) | B |
| NG | C |
A
Click hereDrivetrain>R150 / R151 / R156 MANUAL TRANSMISSION / TRANSAXLE>BACK-UP LIGHT SWITCH>REMOVAL
B
Click hereDrivetrain>R150F /R151F / R156F MANUAL TRANSMISSION / TRANSAXLE>BACK-UP LIGHT SWITCH>REMOVAL
C