Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM › 2011.10–2012.04
RM1840EF _58 Vehicle Interior _009641 THEFT DETERRENT / KEYLESS ENTRY _0052688 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Ignition Switch Circuit  


DESCRIPTION

When the ignition switch assembly is turned to ON, voltage is applied to terminal IG of the theft warning ECU assembly.

WIRING DIAGRAM

B278733
4.833,1.99 6.74,2.198 1.906,0.208 10 false Theft Warning ECU Assembly 4.833,1.823 5.156,1.99 0.323,0.167 10 false G29 5.438,0.594 5.677,0.823 0.24,0.229 10 false IG 5.438,1.521 5.677,1.76 0.24,0.24 10 false E 5.167,0.51 5.354,0.667 0.188,0.156 10 false 18 3.115,0.5 3.302,0.656 0.188,0.156 10 false 1 1.917,0.5 2.042,0.656 0.125,0.156 10 false 4 5.229,1.458 5.365,1.625 0.135,0.167 10 false 1 3.802,0.719 4.969,0.896 1.167,0.177 10 false ECU-IG&GAUGE 0.646,0.583 1.458,0.76 0.813,0.177 10 false from Battery 1.729,1.031 3.313,1.25 1.583,0.219 10 false Ignition Switch Assembly 1.729,0.875 1.969,1.042 0.24,0.167 10 false G9 2.781,0.688 3.094,0.896 0.313,0.208 10 false IG1 2.083,0.688 2.396,0.896 0.313,0.208 10 false AM1

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

When replacing the theft warning ECU assembly, refer to the registration procedures (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(for Built-in Type Door Control Receiver)>REGISTRATION).



PROCEDURE

1.INSPECT IGNITION SWITCH ASSEMBLY
a.
B275965
0.635,0.615 0.823,0.615 0.823,0.615 1.156,1 false 2,0.99 2.333,0.604 2.333,0.604 2.521,0.604 false 0.333,0.542 0.792,0.74 0.458,0.198 10 false AM1 2.573,0.531 3.031,0.729 0.458,0.198 10 false IG1

Remove the ignition switch assembly.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 (IG1) - 4 (AM1) Off, ACC 10 kΩ or higher
ON, Start Below 1 Ω


Result:
Result Proceed to
OK A
NG (for 2TR-FE) B
NG (for 2TR-FBE) C
NG (for 1KD-FTV) D
NG (for 2KD-FTV) E




A

2.CHECK HARNESS AND CONNECTOR (THEFT WARNING ECU - BATTERY AND BODY GROUND)

B

REPLACE IGNITION SWITCH ASSEMBLY

C

REPLACE IGNITION SWITCH ASSEMBLY

D

REPLACE IGNITION SWITCH ASSEMBLY

E

REPLACE IGNITION SWITCH ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (THEFT WARNING ECU - BATTERY AND BODY GROUND)
a.
B274165
0.229,1.146 0.646,1.531 0.417,0.385 0.885,1.198 0.573,0.906 0.573,0.906 0.427,0.906 true 1.26,1.448 1.49,1.854 1.49,1.854 1.677,1.854 true 0.042,0.052 0.354,0.208 0.313,0.156 10 false *a 0.302,0.833 0.458,1.031 0.156,0.198 10 false E 1.719,1.781 2.031,1.979 0.313,0.198 10 false IG 0.292,1.26 0.75,1.458 0.458,0.198 10 false G29
*a Front view of wire harness connector
(to Theft Warning ECU Assembly)


Disconnect the G29 theft warning ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G29-1 (E) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G29-18 (IG) - Body ground Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR