Home › Vehicle Interior › SEAT › FRONT POWER SEAT MOTOR ASSEMBLY(for Slide) › from 2012.10
RM1840EF _58 Vehicle Interior _009646 SEAT _0052722 FRONT POWER SEAT MOTOR ASSEMBLY(for Slide) A

SEAT  FRONT POWER SEAT MOTOR ASSEMBLY(for Slide)  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.


PROCEDURE

Hide 1.INSTALL POWER SEAT MOTOR ASSEMBLY (for Slide)

a.
B211402

Install the slide cable.

NOTICE:

Make sure that the cable is correctly inserted into the power seat motor assembly.



b.
B211399
0.594,1.865 0.313,2.771 0.313,2.771 0.552,2.771 true 1.833,0.792 2.323,0.427 2.323,0.427 2.563,0.427 true 2.594,0.323 2.771,0.469 0.177,0.146 10 false *1 0.583,2.656 0.76,2.802 0.177,0.146 10 false *1
*1 Slide Screw


Install the power seat motor assembly (for Slide) together with the slide cable to the slide screws.

NOTICE:
·

Make sure that the slide rail is locked in the rearmost position.

·

If the serrations on the slide screw and power seat motor assembly with slide cable do not align, grip the slide screw with needle-nose pliers and install the power seat motor assembly together with the slide cable while slightly moving the slide screw. In these cases, do not turn the slide screw 90° or more.

·

Do not apply excessive force to the slide cable (do not bend the slide cable 60° or more).




c.

Using a 4 mm socket hexagon wrench, install the 4 bolts.

Torque:
1.6 N*m (16 kgf*cm, 14 in.*lbf)


d.

Using a 5 mm socket hexagon wrench, install the 2 bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


e.

Install 2 new nuts.

Torque:
2.5 N*m (25 kgf*cm, 22 in.*lbf)


f.

Attach the claw to connect the connector to the seat frame.


g.
B108592
0.116,0.023 0.369,0.2 0.253,0.177 10 *a
*a Component without harness connected
(Power Seat Motor Assembly)


Connect the positive (+) battery terminal to terminal 1 of the power seat motor and the negative (-) battery terminal to terminal 2, and then slide the seat and align the matchmarks.


h.
B211397

Check that the matchmarks are aligned on both sides.

If the matchmarks are not aligned, check the installation condition of the power seat motor assembly, and remove and reinstall the power seat motor assembly if necessary.


i.

Connect the connector.


j.
B211396

Install the seat cushion frame with the 4 bolts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


k.
B211395

Attach the 4 clamps indicated by the arrows in the illustration to install the seat cushion spring.


l.

Attach the 2 wire harness clamps.


Hide 2.INSTALL FRONT SEAT CUSHION COVER WITH PAD

Hide 4.INSTALL FRONT SEAT INNER CUSHION SHIELD LH

Hide 5.INSTALL FRONT POWER SEAT SWITCH LH

Hide 6.INSTALL FRONT SEAT CUSHION SHIELD LH WITH FRONT INNER NO. 1 SEAT CUSHION SHIELD LH

Hide 7.INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB