Home › Vehicle Interior › INTERIOR PANELS / TRIM › UPPER INSTRUMENT PANEL › 2012.04–2012.10
RM1840EF _58 Vehicle Interior _009650 INTERIOR PANELS / TRIM _0052773 UPPER INSTRUMENT PANEL A

INTERIOR PANELS / TRIM  UPPER INSTRUMENT PANEL  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).


PROCEDURE

Hide 1.INSTALL UPPER INSTRUMENT PANEL SUB-ASSEMBLY

a.

Attach the 5 guides and 8 claws to install the upper instrument panel.


b.

Install the 2 bolts <A> and 2 screws <B>.

B278236
5.708,1.031 5.896,1.208 0.188,0.177 10 false *1 1.448,2.417 1.635,2.594 0.188,0.177 10 false *1 5.719,4.406 5.906,4.583 0.188,0.177 10 false *1 1.417,5.75 1.604,5.927 0.188,0.177 10 false *1 3.792,4.802 3.979,4.99 0.188,0.188 10 true *2 5.531,4.042 5.719,4.229 0.188,0.188 10 true *2 5.531,0.646 5.719,0.833 0.188,0.188 10 true *2 3.771,1.479 3.958,1.667 0.188,0.188 10 true *2 1.021,3.75 1.417,4.052 0.396,0.302 10 false *B 1.021,0.323 1.417,0.625 0.396,0.302 10 false *A
*A w/o Front Passenger Airbag *B w/ Front Passenger Airbag
*1 Bolt <A> *2 Screw <B>



Hide 2.INSTALL FRONT PILLAR GARNISH LH

a.

Attach the 2 guides and 2 clips to install the front pillar garnish.


b.

Install the front door opening trim.


Hide 3.INSTALL FRONT PILLAR GARNISH RH

HINT:

Use the same procedure described for the LH side.


Hide 4.INSTALL FRONT ASSIST GRIP SUB-ASSEMBLY (w/ Assist Grip)

Hide 5.INSTALL FRONT NO. 1 ASSIST GRIP PLUG LH (w/ Assist Grip)

Hide 6.INSTALL FRONT NO. 1 ASSIST GRIP PLUG RH (w/ Assist Grip)

Hide 7.INSTALL INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY (w/ Front Passenger Airbag)

Hide 8.INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY (w/ Front Passenger Airbag)

B278068
1.875,1.094 2.073,1.292 0.198,0.198 10 false *1 0.76,1.229 0.958,1.427 0.198,0.198 10 false *1
*1 Hinge


a.

Attach the 2 hinges to install the glove compartment door.


b.
B278069
0.677,1.073 0.875,1.333 0.198,0.26 10 false *1 2.156,0.688 2.354,0.948 0.198,0.26 10 false *1
*1 Stopper


While pushing in the sides of the glove compartment door as indicated by the arrows in the illustration, close the door to engage it to the 2 stoppers.


Hide 9.INSTALL RADIO TUNER OPENING COVER (w/o Audio)

a.

Install the radio tuner opening cover with the 4 screws.


Hide 10.INSTALL RADIO RECEIVER ASSEMBLY (w/ Audio)

Hide 11.INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY

a.

for Manual Air Conditioning System:

i.

Connect the connectors.


ii.

Attach the 4 claws to connect the air conditioner control.


iii.

Attach the 10 claws and 4 clips to install the center instrument cluster finish panel.



b.

for Automatic Air Conditioning System:

i.

Connect the connectors.


ii.

Attach the 8 claws and 4 clips to install the center instrument cluster finish panel.



Hide 13.INSTALL NO. 1 INSTRUMENT CLUSTER FINISH PANEL

a.

Attach the 3 guides and 2 claws to install the No. 1 instrument cluster finish panel.


b.

Install the clip <C>.


Hide 14.INSTALL STEERING WHEEL ASSEMBLY

Hide 15.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (w/ Airbag System)

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 16.CHECK SRS WARNING LIGHT (w/ Airbag System)