1. TABLE OF BOLT, SCREW AND NUT
All bolts, screws, nuts and clips relevant to installing and removing the instrument panel are shown along with their alphabetical code in the table.
2. PRECAUTION (w/ Airbag System)
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Airbag System)
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
4.REMOVE STEERING WHEEL ASSEMBLY
5.REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL
Remove the clip <C>.
Detach the 2 claws and 3 guides and remove the No. 1 instrument cluster finish panel.
6.REMOVE COMBINATION METER ASSEMBLY
7.REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY
for Manual Air Conditioning System:
| *1 | Protective Tape |
Put protective tape around the center instrument cluster finish panel.
Using a moulding remover, detach the 10 claws and 4 clips.
Detach the 4 claws and disconnect the air conditioner control.
Disconnect the connectors and remove the center instrument cluster finish panel.
for Automatic Air Conditioning System:
| *1 | Protective Tape |
Put protective tape around the center instrument cluster finish panel.
Using a moulding remover, detach the 8 claws and 4 clips.
Disconnect the connectors and remove the center instrument cluster finish panel.
8.REMOVE RADIO RECEIVER ASSEMBLY (w/ Audio)
for Radio Receiver Type:
(See page Audio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER>REMOVAL)
for Radio and Display Type:
(See page Audio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER>REMOVAL)
9.REMOVE NAVIGATION RECEIVER ASSEMBLY (w/ Navigation System)
10.REMOVE RADIO TUNER OPENING COVER (w/o Audio)
Remove the 4 screws and radio tuner opening cover.
11.REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY (w/ Front Passenger Airbag)
| *1 | Stopper |
Slightly bend the upper part of the glove compartment door to release the 2 stoppers and open the glove compartment door until it is horizontal.
| *1 | Hinge |
Pull the glove compartment door toward the rear of the vehicle to detach the 2 hinges and remove the glove compartment door.
12.REMOVE INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY (w/ Front Passenger Airbag)
13.REMOVE ASSIST GRIP PLUG LH (w/ Assist Grip)
14.REMOVE ASSIST GRIP PLUG RH (w/ Assist Grip)
15.REMOVE FRONT ASSIST GRIP SUB-ASSEMBLY (w/ Assist Grip)
16.REMOVE FRONT PILLAR GARNISH LH
Remove the part of the front door opening trim attached to the front pillar garnish.
Detach the 2 clips and 2 guides and remove the front pillar garnish.
17.REMOVE FRONT PILLAR GARNISH RH
Use the same procedure described for the LH side.
18.REMOVE UPPER INSTRUMENT PANEL SUB-ASSEMBLY
Put protective tape around the upper instrument panel.
Remove the 2 bolts <A> and 2 screws <B>.
Using a screwdriver, detach the 8 claws and 5 guides and remove the upper instrument panel.
Tape the screwdriver tip before use.
| *A | w/o Front Passenger Airbag | *B | w/ Front Passenger Airbag |
| *1 | Protective Tape | *2 | Bolt <A> |
| *3 | Screw <B> | - | - |