Home › Vehicle Interior › INTERIOR PANELS / TRIM › LOWER INSTRUMENT PANEL › 2012.04–2012.10
RM1840EF _58 Vehicle Interior _009650 INTERIOR PANELS / TRIM _0052774 LOWER INSTRUMENT PANEL A

INTERIOR PANELS / TRIM  LOWER INSTRUMENT PANEL  REMOVAL  


PROCEDURE

Hide 1. TABLE OF BOLT, SCREW AND NUT

a.

All bolts, screws, nuts and clips relevant to installing and removing the instrument panel are shown along with an alphabetical code in the table.

B277625
2.5,1 2.917,1.26 0.417,0.26 10 false <B> 0.177,1.01 0.552,1.219 0.375,0.208 10 false <A> 2.51,1.948 2.958,2.229 0.448,0.281 10 false <E> 0.188,1.948 0.563,2.135 0.375,0.188 10 false <D> 4.844,1.021 5.281,1.271 0.438,0.25 10 false <C> 0.167,0.26 0.542,0.438 0.375,0.177 10 false Code 1.25,0.25 1.698,0.438 0.448,0.188 10 false Shape 4.792,0.25 5.167,0.427 0.375,0.177 10 false Code 5.875,0.25 6.323,0.438 0.448,0.188 10 false Shape 2.458,0.25 2.833,0.427 0.375,0.177 10 false Code 3.5,0.25 3.948,0.438 0.448,0.188 10 false Shape 5.302,2.021 6.656,2.25 1.354,0.229 10 false mm (in.) (L = Length) 6.427,1.156 6.896,1.323 0.469,0.167 10 false L = 20 1.635,1.188 2.094,1.365 0.458,0.177 10 false L = 14 6.427,0.771 6.802,0.938 0.375,0.167 10 false φ = 5 1.635,0.802 2.031,0.99 0.396,0.188 10 false φ = 5 4.073,1.719 4.49,1.906 0.417,0.188 10 false φ = 5 4.073,2.094 4.521,2.281 0.448,0.188 10 false L = 16 1.583,1.875 1.99,2.052 0.406,0.177 10 false φ = 6 1.635,0.948 2.094,1.156 0.458,0.208 10 false (0.197) 1.635,1.323 2.115,1.521 0.479,0.198 10 false (0.551) 6.427,0.938 6.938,1.135 0.51,0.198 10 false (0.197) 6.417,1.323 6.896,1.51 0.479,0.188 10 false (0.787) 1.594,2.052 2.042,2.25 0.448,0.198 10 false (0.236) 4.083,1.875 4.552,2.063 0.469,0.188 10 false (0.197) 4.063,2.24 4.531,2.417 0.469,0.177 10 false (0.630)


Hide 2. PRECAUTION (w/ Airbag System)

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Airbag System)

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 4.REMOVE UPPER INSTRUMENT PANEL SUB-ASSEMBLY

Hide 5.REMOVE HEADLIGHT DIMMER SWITCH ASSEMBLY

Hide 6.REMOVE CONSOLE BOX ASSEMBLY (w/ Console Box Lid)

Hide 8.REMOVE FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure described for the LH side.


Hide 9.REMOVE COWL SIDE TRIM BOARD LH

B277609

a.

Remove the part of the front door opening trim attached to the cowl side trim board.


b.

Remove the clip.


c.

Detach the 2 clips and remove the cowl side trim board.


Hide 10.REMOVE COWL SIDE TRIM BOARD RH

HINT:

Use the same procedure described for the LH side.


Hide 14.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY

B278242

a.

Detach the 2 claws, 3 clips and 3 guides and remove the lower instrument panel finish panel.


Hide 15.REMOVE NO. 1 INSTRUMENT PANEL BOX

B278243

a.

Remove the 6 screws <A>.


b.

Disconnect the connectors, detach the clamp and remove the No. 1 instrument panel box.


Hide 17.REMOVE LOWER CENTER INSTRUMENT PANEL FINISH PANEL (w/o Console Box, w/o Console Box Lid)

B278244

a.

Using a clip remover, remove the 2 clips <B>.


b.

Detach the 3 claws and remove the lower center instrument panel finish panel.


Hide 18.REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY (w/o Front Passenger Airbag)

Hide 19.REMOVE SWITCH BASE

B278245

a.

Detach the 9 claws and guide.

HINT:

If the claws are difficult to detach, detach the claws from the back of the switch base.



b.

Disconnect the connectors and remove the switch base.


Hide 20.REMOVE NO. 1 SWITCH HOLE BASE

B278246
2.417,0.688 2.885,0.896 true 2.938,0.813 3.146,1.021 0.208,0.208 10 false *1
*1 Protective Tape


a.

Put protective tape around the No. 1 switch hole base.


b.

Using a moulding remover, detach the 5 claws.


c.

Disconnect the connectors and remove the No. 1 switch hole base.


Hide 21.REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY

a.

Using a clip remover, remove the 2 clips <B>.


b.

Remove the 2 bolts <C>, nut <D> and 3 screws <E>.


c.

Disconnect the hood lock control cable, fuel lid lock control cable and DLC3.


d.

Disconnect the connectors and detach the clamps.


e.

Detach the 2 guides and remove the lower instrument panel.


f.

for Automatic Air Conditioning System:

Disconnect the room temperature sensor.

B278247
6.479,1.115 6.656,1.281 0.177,0.167 10 false *1 1,2.76 1.177,2.927 0.177,0.167 10 false *1 6.281,2.479 6.458,2.646 0.177,0.167 10 false *2 1.281,3.813 1.458,3.979 0.177,0.167 10 false *2 2.927,1.406 3.104,1.573 0.177,0.167 10 true *3 5.125,2.677 5.302,2.844 0.177,0.167 10 false *4 3.885,3.354 4.063,3.521 0.177,0.167 10 false *4 5.104,0.49 5.281,0.656 0.177,0.167 10 false *4 2.219,3.448 2.396,3.615 0.177,0.167 10 false *5 1.75,3.49 1.927,3.656 0.177,0.167 10 true *6 2.5,3.281 2.677,3.448 0.177,0.167 10 false *7 4.969,3.969 5.146,4.135 0.177,0.167 10 true *8 3.313,5.021 3.521,5.188 0.208,0.167 10 true *8 2.281,5.052 2.458,5.219 0.177,0.167 10 true *8 3.969,5 4.146,5.167 0.177,0.167 10 true *8 5.771,1.146 5.948,1.313 0.177,0.167 10 true *9 1.823,2.344 2,2.51 0.177,0.167 10 true *9 3.917,2.052 4.094,2.219 0.177,0.167 10 true *8
*1 Clip <B> *2 Bolt <C>
*3 Nut <D> *4 Screw <E>
*5 Hood Lock Control Cable *6 Fuel Lid Lock Control Cable
*7 DLC3 *8 Clamp
*9 Guide - -