Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING UNIT › 2012.04–2012.10
RM1840EF _58 Vehicle Interior _009648 HEATING / AIR CONDITIONING _0052749 AIR CONDITIONING UNIT A

HEATING / AIR CONDITIONING  AIR CONDITIONING UNIT  REMOVAL  


PROCEDURE

Hide 1.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

Hide 3. PRECAUTION (w/ Airbag System)

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 4.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Airbag System)

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 5.DISCONNECT SUCTION HOSE SUB-ASSEMBLY

a.
E173197

E173198
1.813,0.906 2,1.104 0.188,0.198 10 false *a
*a Disconnect tube by hand


Remove the bolt and disconnect the suction hose sub-assembly.

NOTICE:
·

Do not use a screwdriver or similar tool to disconnect the suction hose sub-assembly.


·

Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering.




b.

Remove the O-ring from the suction hose sub-assembly.


Hide 6.DISCONNECT AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY

a.

Disconnect the air conditioning tube and accessory assembly.

NOTICE:
·

Do not use a screwdriver or similar tool to disconnect the air conditioning tube and accessory assembly.

·

Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering.




b.

Remove the O-ring from the air conditioning tube and accessory assembly.


Hide 7.DISCONNECT HEATER WATER INLET HOSE

E225468

a.

Using pliers, grip the claws of the clip and slide the clip to disconnect the heater water inlet hose.

HINT:

Collect the engine coolant in a container.



Hide 8.DISCONNECT HEATER WATER OUTLET HOSE

E225469

a.

Using pliers, grip the claws of the clip and slide the clip to disconnect the heater water outlet hose.

HINT:

Collect the engine coolant in a container.



Hide 9.REMOVE UPPER INSTRUMENT PANEL SUB-ASSEMBLY

Hide 10.REMOVE NO. 2 HEATER TO REGISTER DUCT

E225181

a.

Remove the 3 clips and No. 2 heater to register duct.


Hide 11.REMOVE NO. 1 HEATER TO REGISTER DUCT

E225182

a.

Remove the clip.


b.

Detach the 3 claws and remove the No. 1 heater to register duct.


Hide 12.REMOVE NO. 3 HEATER TO REGISTER DUCT

E271837

a.

Remove the clip.


b.

Detach the 4 claws and remove the No. 3 heater to register duct.


Hide 13.REMOVE DEFROSTER NOZZLE ASSEMBLY (w/ Defroster)

E225184

a.

Using a screwdriver, detach the 4 clips and remove the defroster nozzle assembly.


Hide 14.REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY

Hide 15.REMOVE STEERING COLUMN ASSEMBLY

Hide 16.REMOVE NO. 1 AIR DUCT

E226311

a.

Detach the 2 claws and remove the No. 1 air duct.


Hide 17.REMOVE NO. 2 AIR DUCT

E226312

a.

Detach the 2 claws and remove the No. 2 air duct.


Hide 18.REMOVE NO. 4 AIR DUCT

E226313

a.

Detach the 2 claws and remove the No. 4 air duct.


Hide 19.REMOVE NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

E271838
1.115,0.615 1.427,0.813 0.313,0.198 10 false *1 2.521,1.208 2.833,1.406 0.313,0.198 10 false *1 1.896,0.052 2.208,0.25 0.313,0.198 10 false *3 0.802,0.542 1.115,0.74 0.313,0.198 10 false *2 1.594,1.406 1.906,1.604 0.313,0.198 10 false *2 1.635,1.719 1.948,1.917 0.313,0.198 10 false *4
*1 Screw
*2 Nut A
*3 Nut B
*4 Bolt


a.

Detach the 2 clamps and remove the 2 nuts labeled A.


b.

Disconnect the connectors and remove the driver side junction block.


c.

Remove the screw.


d.

Remove the bolt, nut labeled B and No. 1 instrument panel brace sub-assembly.


Hide 20.REMOVE AIR CONDITIONING DUCT SUB-ASSEMBLY (for Automatic Air Conditioning System)

E225928

a.

Detach the 2 claws and remove the air conditioning duct sub-assembly.


Hide 22.REMOVE INSTRUMENT PANEL REINFORCEMENT

a.
E225186

Disconnect the connector and detach the 3 clamps.


b.
E236006

for Automatic Air Conditioning System:

Detach the clamp and disconnect the 2 connectors.


c.
E236005

for Manual Air Conditioning System:

Detach the clamp and disconnect the 2 connectors.


d.
E225188

Remove the 2 bolts and disconnect the ground wires from the instrument panel reinforcement.


e.
E225885

Remove the grommet from the vehicle body.


f.

Detach the 12 clamps.

E225189


g.

Disconnect the connectors.


h.

Remove the 3 bolts.

E225190


i.

for Automatic Transmission:

Remove the 7 bolts and instrument panel reinforcement.


j.

for Manual Transmission:

Remove the 8 bolts and instrument panel reinforcement.

E225191
1.146,1.292 1.292,1.292 1.292,1.292 1.292,1.479 false 1.198,1.521 1.396,1.698 0.198,0.177 10 false *A
*A for Manual Transmission - -



Hide 23.REMOVE NO. 1 COOLER UNIT DRAIN HOSE

E225884

a.

Remove the No. 1 cooler unit drain hose.


Hide 24.REMOVE AIR CONDITIONING UNIT ASSEMBLY

E225192

a.

Remove the bolt, nut and air conditioning unit assembly.


Hide 25.REMOVE NO. 3 AIR DUCT

E226397

a.

Detach the 2 claws and remove the No. 3 air duct.