1. PRECAUTION (w/ Airbag System)
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Airbag System)
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
3.REMOVE FRONT SEAT ASSEMBLY LH
4.REMOVE FRONT SEAT ASSEMBLY RH
for Manual Seat:
Use the same procedure described for the LH side.
for Bench Seat Type:
(See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Bench Seat Type)>REMOVAL)
5.REMOVE FRONT DOOR SCUFF PLATE LH
| *1 | Protective Tape |
Put protective tape around the front door scuff plate.
Using a moulding remover, detach the 4 clips and 8 claws and remove the front door scuff plate.
6.REMOVE FRONT DOOR SCUFF PLATE RH
Use the same procedure described for the LH side.
7.REMOVE FRONT DOOR OPENING TRIM LH
Remove the front door opening trim.
8.REMOVE FRONT DOOR OPENING TRIM RH
Use the same procedure described for the LH side.
9.REMOVE FRONT NO. 1 ASSIST GRIP PLUG LH (w/ Assist Grip)
| *1 | Protective Tape |
Use the same procedure for both front No. 1 assist grip plugs.
Using a screwdriver, detach the 2 claws and remove the front No. 1 assist grip plug.
Tape the screwdriver tip before use.
10.REMOVE FRONT NO. 1 ASSIST GRIP PLUG RH (w/ Assist Grip)
Use the same procedure described for the LH side.
11.REMOVE FRONT ASSIST GRIP SUB-ASSEMBLY (w/ Assist Grip)
Use the same procedure for both front assist grips.
Remove the 2 screws and front assist grip.
12.REMOVE FRONT PILLAR GARNISH LH
Detach the 2 clips and 2 guides and remove the front pillar garnish.
13.REMOVE FRONT PILLAR GARNISH RH
Use the same procedure described for the LH side.
14.REMOVE UPPER BACK PANEL GARNISH
Detach the 4 claws, 4 guides and 5 clips and remove the upper back panel garnish.
15.REMOVE LOWER QUARTER TRIM PANEL LH
Remove the bolt and disconnect the front seat outer belt floor anchor.
Detach the claw, 3 clips and 2 guides and remove the lower quarter trim panel.
16.REMOVE LOWER QUARTER TRIM PANEL RH
Use the same procedure described for the LH side.
17.REMOVE QUARTER INSIDE TRIM BOARD LH
| *1 | Protective Tape |
Using a screwdriver, detach the 2 claws and open the front seat belt shoulder anchor cover.
Tape the screwdriver tip before use.
Remove the bolt and disconnect the front seat belt shoulder anchor.
Detach the 3 clips and remove the quarter inside trim board.
18.REMOVE QUARTER INSIDE TRIM BOARD RH
Use the same procedure described for the LH side.
19.REMOVE NO. 1 ROOM LIGHT ASSEMBLY
20.REMOVE VISOR ASSEMBLY LH
Detach the guide.
Remove the 2 screws and visor.
21.REMOVE VISOR ASSEMBLY RH
Use the same procedure described for the LH side.
22.REMOVE VISOR HOLDER LH
Remove the screw.
Detach the 2 claws and remove the visor holder.
23.REMOVE VISOR HOLDER RH
Use the same procedure described for the LH side.
24.REMOVE ASSIST GRIP
| *1 | Protective Tape |
Using a screwdriver, detach the 4 claws and open the 2 covers.
Tape the screwdriver tip before use.
Remove the 2 screws and assist grip.
25.REMOVE UPPER INSTRUMENT PANEL SUB-ASSEMBLY
26.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY
27.REMOVE NO. 2 HEATER TO REGISTER DUCT
28.REMOVE NO. 1 HEATER TO REGISTER DUCT
29.REMOVE NO. 3 HEATER TO REGISTER DUCT
30.REMOVE DEFROSTER NOZZLE ASSEMBLY (w/ Defroster)
31.REMOVE ROOF HEADLINING ASSEMBLY
Detach the 4 clamps from the front pillar.
Disconnect the connectors and detach the 4 clamps.
Using a clip remover, remove the 5 clips.
Remove the roof headlining as shown in the illustration.
Be careful not to damage the roof headlining when removing it.
32.REMOVE FRONT SIDE RAIL SPACER LH
Detach the 2 claws and remove the front side rail spacer.
33.REMOVE FRONT SIDE RAIL SPACER RH
Use the same procedure described for the LH side.
34.REMOVE SIDE RAIL SPACER
Detach the 2 claws and remove the side rail spacer.
35.REMOVE REAR NO. 2 SIDE RAIL SPACER LH
Detach the 2 claws and remove the rear No. 2 side rail spacer.
36.REMOVE REAR NO. 2 SIDE RAIL SPACER RH
Use the same procedure described for the LH side.