Home › Vehicle Exterior › WINDOW / GLASS › BACK WINDOW GLASS(for Double Cab) › from 2012.10
RM1840EF _59 Vehicle Exterior _009651 WINDOW / GLASS _0052791 BACK WINDOW GLASS(for Double Cab) A

WINDOW / GLASS  BACK WINDOW GLASS(for Double Cab)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).


PROCEDURE

Hide 1.INSTALL NO. 1 BACK WINDOW GLASS STOPPER

a.
B085122
1.406,0.552 1.958,0.552 false 1.156,1.542 1.042,1.281 1.042,1.281 0.885,1.281 false 1.229,0.438 1.375,0.625 0.146,0.188 10 false *1 0.708,1.167 0.875,1.344 0.167,0.177 10 false *2
*1 Vehicle Body
*2 No. 1 Back Window Glass Stopper


Install 2 new No. 1 back window glass stoppers to the vehicle body as shown in the illustration.


Hide 2.INSTALL NO. 2 BACK WINDOW GLASS STOPPER

a.
B282360
1.063,0.74 0.917,0.948 0.917,0.948 0.75,0.948 false 1.719,0.76 1.906,0.521 1.906,0.521 2.063,0.521 false 0.094,0.104 0.323,0.281 0.229,0.177 10 false *a 2.115,0.448 2.292,0.604 0.177,0.156 10 false *1 0.531,0.854 0.771,1.094 0.24,0.24 10 false *2 2.052,1.479 2.188,1.646 0.135,0.167 10 false a 2.719,0.719 2.854,0.885 0.135,0.167 10 false b
*1 Ceramic Notch
*2 Ceramic Line
*a Backside


Apply Primer G to the back window glass where the No. 2 back window glass stoppers will be installed.

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.



HINT:

If the primer is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer.



b.

Install 2 new No. 2 back window glass stoppers to the back window glass as shown in the illustration.

Standard:
Area Specified Condition
a 40.0 mm (1.575 in.)
b 16.3 mm (0.642 in.)



Hide 3.INSTALL BACK WINDOW GLASS SPACER

a.
B282361
1.146,2.76 0.896,2.76 false 2.292,2.76 2.542,2.76 false 1.719,1.948 1.646,1.844 1.646,1.844 1.302,1.844 false 0.708,2.667 0.938,2.854 0.229,0.188 10 false *1 1.125,1.75 1.354,1.938 0.229,0.188 10 false *1 0.115,0.104 0.344,0.292 0.229,0.188 10 false *a 2.563,2.667 2.792,2.854 0.229,0.188 10 false *1
*1 Ceramic Notch
*a Backside


Apply Primer G to the back window glass where the back window glass spacers will be installed.

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.



HINT:

If the primer is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer.



b.

Install 2 new back window glass spacers to the back window glass as shown in the illustration.


Hide 4.INSTALL NO. 1 BACK WINDOW MOULDING

a.

Apply Primer G to the back window glass where the No. 1 back window moulding and dam will be installed.

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.



HINT:

If the primer is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer.


B282362
4.823,1.219 4.656,0.979 4.656,0.979 4.51,0.979 false 6.188,1.229 6.021,0.99 6.021,0.99 5.875,0.99 false 0.115,0.063 0.313,0.24 0.198,0.177 10 false *a 1.594,0.354 1.844,0.563 0.25,0.208 10 false A 0.396,0.875 0.542,1.052 0.146,0.177 10 false A 0.75,0.99 0.885,1.167 0.135,0.177 10 false A 1.604,0.76 1.813,0.958 0.208,0.198 10 false A 3.229,0.531 3.406,0.719 0.177,0.188 10 false A 2.75,0.75 2.906,0.938 0.156,0.188 10 false A 2.094,0.938 2.292,1.135 0.198,0.198 10 false B 2.094,1.323 2.333,1.552 0.24,0.229 10 false B 0.49,1.5 0.708,1.646 0.219,0.146 10 false *1 4,0.313 4.646,0.531 0.646,0.219 10 false A - A 5.5,0.323 5.958,0.51 0.458,0.188 10 false B - B 4.875,0.427 5.073,0.594 0.198,0.167 10 false a 6.302,0.438 6.49,0.615 0.188,0.177 10 false b 6.698,0.771 6.854,0.979 0.156,0.208 10 false c 4.344,0.885 4.51,1.063 0.167,0.177 10 false *2 5.708,0.896 5.875,1.073 0.167,0.177 10 false *2
*1 Primer G *2 Dam Reference Line
*a Backside - -


Standard:
Area Specified Condition
a 6.4 mm (0.252 in.)
b 12.7 mm (0.500 in.)
c 7.5 mm (0.295 in.)



b.

Remove the peeling paper from the adhesive part of a new No. 1 back window moulding. Install the No. 1 back window moulding (adhesive side) to the back window glass (Primer G area) as shown in the illustration.

B282363
4.542,1.927 4.781,1.927 false 6.24,1.927 6.01,1.927 false 5.615,0.635 5.385,0.365 5.385,0.365 5.229,0.365 false 0.156,0.115 0.344,0.323 0.188,0.208 10 false *a 0.354,1.344 0.552,1.542 0.198,0.198 10 false A 0.792,1.521 0.99,1.719 0.198,0.198 10 false A 2.083,0.875 2.281,1.073 0.198,0.198 10 false A 2.083,1.302 2.281,1.5 0.198,0.198 10 false A 2.844,1.479 3.042,1.677 0.198,0.198 10 false A 3.323,1.302 3.521,1.5 0.198,0.198 10 false A 0.417,1.771 0.552,1.927 0.135,0.156 10 false B 3.271,1.781 3.438,1.958 0.167,0.177 10 false C 3.958,0.188 4.375,0.417 0.417,0.229 10 false A - A 5.052,0.292 5.24,0.448 0.188,0.156 10 false *2 3.969,1.479 4.219,1.75 0.25,0.271 10 false B 5.406,1.479 5.594,1.667 0.188,0.188 10 false C 5.74,1.042 5.927,1.229 0.188,0.188 10 false a 4.792,1.844 5.031,2.021 0.24,0.177 10 false *1 5.844,1.844 6.083,2.021 0.24,0.177 10 false *1
*1 Ceramic Notch *2 Dam Reference Line
*a Backside - -


Standard:
Area Specified Condition
a 6.4 mm (0.252 in.)



Hide 5.INSTALL BACK WINDOW GLASS ADHESIVE DAM

a.

Remove the peeling paper from the adhesive part of a new back window glass adhesive dam. Install the back window glass adhesive dam (adhesive side) to the back window glass (Primer G area) as shown in the illustration.

B282364
4.5,0.604 4.615,0.479 4.615,0.479 4.698,0.479 false 6.104,0.604 5.99,0.49 5.99,0.49 5.906,0.49 false 5.229,1.896 5.49,1.615 5.49,1.615 5.75,1.615 false 0.115,0.094 0.344,0.323 0.229,0.229 10 false *a 0.542,1.813 0.823,2.052 0.281,0.24 10 false A 3.969,0.156 4.25,0.396 0.281,0.24 10 false A 2.073,1.438 2.344,1.656 0.271,0.219 10 false C 2.073,1.823 2.344,2.042 0.271,0.219 10 false C 3.146,1.781 3.396,1.948 0.25,0.167 10 false B 5.406,0.146 5.656,0.313 0.25,0.167 10 false B 3.969,1.448 4.365,1.625 0.396,0.177 10 false C - C 4.74,0.396 4.927,0.635 0.188,0.24 10 false *1 5.781,1.521 6.042,1.688 0.26,0.167 10 false *2 5.781,2.24 5.99,2.448 0.208,0.208 10 false a 5.729,0.375 5.917,0.615 0.188,0.24 10 false *1
*1 Ceramic Notch *2 Dam Reference Line
*a Backside - -


Standard measurement:
Area Specified Condition
a 7.5 mm (0.295 in.)



Hide 6.INSTALL BACK WINDOW GLASS

a.
B282365
1.885,0.75 2.063,0.75 2.063,0.75 2.302,1.063 false 1.906,1.875 2.094,1.875 2.094,1.875 2.281,2.083 false 2.24,2.198 2.01,2.448 2.01,2.448 1.615,2.448 false 0.615,4.396 0.865,4.594 0.25,0.198 10 false *1 1.708,0.656 1.938,0.833 0.229,0.177 10 false *1 1.708,1.792 1.938,1.969 0.229,0.177 10 false *1 1.427,2.344 1.708,2.563 0.281,0.219 10 false *2 2.385,0.125 2.688,0.344 0.302,0.219 10 false *a 2.375,2.313 2.688,2.542 0.313,0.229 10 false *b
*1 Primer M
*2 Adhesive
*a CORRECT
*b INCORRECT


Using a brush, apply Primer M to the exposed part of the vehicle body.

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Do not apply Primer M to the adhesive.

·

Throw away any leftover primer.

·

Do not apply too much primer.



HINT:

If the primer is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer.



b.

Using a brush or sponge, apply Primer G to the contact surface of the back window glass.

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.



HINT:

If the primer is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer.


B282366
4.406,0.688 4.625,0.688 false 6.396,0.688 6.208,1.01 6.208,1.01 6.073,1.01 false 6.385,2 6.188,1.74 6.188,1.74 6.073,1.74 false 4.615,2.042 4.375,2.104 4.375,2.104 4.615,2.156 true 0.104,0.094 0.281,0.26 0.177,0.167 10 false *a 0.406,1.458 0.594,1.615 0.188,0.156 10 false C 2.833,1.469 3.021,1.625 0.188,0.156 10 false C 2.833,1.823 3.021,1.979 0.188,0.156 10 false C 0.417,1.792 0.604,1.948 0.188,0.156 10 false C 1.646,1.458 1.792,1.604 0.146,0.146 10 false D 1.656,1.885 1.854,2.052 0.198,0.167 10 false D 0.385,1.156 0.583,1.354 0.198,0.198 10 false B 0.917,1.448 1.115,1.646 0.198,0.198 10 false B 1.646,1.208 1.792,1.365 0.146,0.156 10 false B 1.646,0.875 1.844,1.073 0.198,0.198 10 false B 2.781,1.25 2.979,1.448 0.198,0.198 10 false B 3.281,1.073 3.49,1.281 0.208,0.208 10 false B 0.969,0.896 1.167,1.094 0.198,0.198 10 false A 0.99,1.24 1.177,1.427 0.188,0.188 10 false A 2.313,0.896 2.5,1.083 0.188,0.188 10 false A 2.323,1.271 2.51,1.458 0.188,0.188 10 false A 3.875,0.156 4.458,0.406 0.583,0.25 10 false A - A 5.438,0.156 5.854,0.354 0.417,0.198 10 false B - B 3.865,1.448 4.281,1.635 0.417,0.188 10 false C - C 5.427,1.448 5.885,1.656 0.458,0.208 10 false D - D 4.229,0.594 4.438,0.76 0.208,0.167 10 false *2 0.49,2.521 0.875,2.708 0.385,0.188 10 false *1 5.917,0.917 6.125,1.083 0.208,0.167 10 false *2 4.208,2.01 4.417,2.177 0.208,0.167 10 false *2 5.906,1.677 6.115,1.844 0.208,0.167 10 false *2
*1 Primer G *2 Adhesive Center Line
*a Backside - -



c.

Apply adhesive to the back window glass.

Adhesive:

Toyota Genuine Windshield Glass Adhesive or equivalent


i.

Cut off the tip of a cartridge nozzle as shown in the illustration.

HINT:

After cutting off the tip, use all adhesive within the time written in the table below.


Usage Time Frame:
Temperature Usage Time Frame
35°C (95°F) 15 minutes
20°C (68°F) 1 hour 40 minutes
5°C (41°F) 8 hours



ii.

Load a sealer gun with the cartridge.


iii.

Apply adhesive to the glass as shown in the illustration.

B282367
6.729,1.99 6.531,1.729 6.531,1.729 6.406,1.729 true 5.427,0.635 5.167,0.896 5.167,0.896 5.073,0.896 true 6.74,0.635 6.479,0.896 6.479,0.896 6.385,0.896 true 5.427,1.896 5,1.802 5,1.802 5.427,2.01 true 0.094,0.094 0.354,0.302 0.26,0.208 10 false *a 1.406,1.438 1.594,1.594 0.188,0.156 10 false C 3.854,1.427 4.042,1.583 0.188,0.156 10 false C 3.854,1.813 4.042,1.969 0.188,0.156 10 false C 1.417,1.802 1.604,1.958 0.188,0.156 10 false C 2.635,1.438 2.781,1.583 0.146,0.146 10 false D 2.635,1.802 2.833,1.969 0.198,0.167 10 false D 1.385,1.167 1.583,1.365 0.198,0.198 10 false B 1.906,1.438 2.104,1.635 0.198,0.198 10 false B 2.635,1.198 2.781,1.354 0.146,0.156 10 false B 2.625,0.833 2.823,1.031 0.198,0.198 10 false B 3.781,1.229 3.979,1.427 0.198,0.198 10 false B 4.281,1.031 4.49,1.24 0.208,0.208 10 false B 1.958,0.833 2.156,1.031 0.198,0.198 10 false A 1.969,1.219 2.156,1.406 0.188,0.188 10 false A 3.313,0.833 3.5,1.021 0.188,0.188 10 false A 3.313,1.208 3.5,1.396 0.188,0.188 10 false A 4.521,0.115 5.104,0.365 0.583,0.25 10 false A - A 5.833,0.115 6.25,0.313 0.417,0.198 10 false B - B 4.51,1.396 4.927,1.583 0.417,0.188 10 false C - C 5.823,1.396 6.281,1.604 0.458,0.208 10 false D - D 4.917,0.792 5.125,0.958 0.208,0.167 10 false *2 1.021,2.365 1.25,2.542 0.229,0.177 10 false *1 4.844,1.698 5.052,1.865 0.208,0.167 10 false *2 6.25,1.625 6.458,1.792 0.208,0.167 10 false *2 6.229,0.792 6.438,0.958 0.208,0.167 10 false *2 4.813,0.406 5.031,0.573 0.219,0.167 10 false a 6.125,0.406 6.313,0.583 0.188,0.177 10 false a 4.823,2.115 5.052,2.333 0.229,0.219 10 false c 6.125,2.115 6.26,2.313 0.135,0.198 10 false d 0.646,1.49 0.833,1.76 0.188,0.271 10 false a 0.25,2.323 0.458,2.531 0.208,0.208 10 false a 1.042,1.635 1.188,1.844 0.146,0.208 10 false b 0.615,1.979 0.865,2.229 0.25,0.25 10 false b
*1 Adhesive *2 Adhesive Center Line
*a Backside - -


Standard:
Area Specified Condition
a 12.0 mm (0.472 in.)
b 8.0 mm (0.315 in.)
c 16.6 mm (0.654 in.)
d 17.7 mm (0.697 in.)




d.

Install the back window glass to the vehicle body.

i.

Lightly press the front surface of the back window glass to ensure that it is securely fit to the vehicle body.

NOTICE:
·

Check that the spacers are attached to the vehicle body correctly.

·

Check that the vehicle body and back window glass have a small gap between them.




ii.

Hold the back window glass in place securely with protective tape or equivalent until the adhesive hardens.

NOTICE:

Do not drive the vehicle for the amount of time written in the table below.


Minimum Time:
Temperature Minimum Time Prior to Driving Vehicle
35°C (95°F) 1 hour 30 minutes
20°C (68°F) 5 hours
5°C (41°F) 24 hours




e.

w/ Defogger:

Connect the back window defogger connector.


Hide 7.CHECK FOR LEAKS AND REPAIR

a.

Conduct a leak test after the adhesive has completely hardened.


b.

Seal any leaks with auto glass sealer.


Hide 16.INSTALL REAR DOOR OPENING TRIM RH

HINT:

Use the same procedure described for the LH side.