Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM › from 2012.10
RM1840EF _51 Engine / Hybrid System _009572 1GR-FE ENGINE CONTROL _0052127 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0037  Oxygen Sensor Heater Control Circuit Low (Bank 1 Sensor 2)  P0038  Oxygen Sensor Heater Control Circuit High (Bank 1 Sensor 2)  P0057  Oxygen Sensor Heater Control Circuit Low (Bank 2 Sensor 2)  P0058  Oxygen Sensor Heater Control Circuit High (Bank 2 Sensor 2)  


DESCRIPTION

Refer to DTC P0136 (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>P0136).

HINT:
·

When any of these DTCs are stored, the ECM enters fail-safe mode. The ECM turns off the heated oxygen sensor heater in fail-safe mode. Fail-safe mode continues until the ignition switch is turned off.

·

The ECM provides a pulse-width modulated control circuit to adjust the current through the heater. The heated oxygen sensor heater circuit uses a relay on the +B side of the circuit.

A303213
0.115,0.125 3.26,0.375 3.146,0.25 10 false Reference (System Diagram of Bank 1 Sensor 2) 0.313,1.177 1.229,1.406 0.917,0.229 10 false From Battery 1.51,1.021 1.833,1.198 0.323,0.177 10 false EFI 2.313,0.646 2.698,0.844 0.385,0.198 10 false MAIN 3.531,0.615 5.031,0.833 1.5,0.219 10 false Heated Oxygen Sensor 5.885,0.552 6.271,0.75 0.385,0.198 10 false ECM 4.073,1 4.531,1.229 0.458,0.229 10 false Heater 4.063,1.625 4.552,1.854 0.49,0.229 10 false Sensor 3.74,1.083 4.125,1.281 0.385,0.198 10 false +B 3.76,1.719 4.146,1.917 0.385,0.198 10 false E2 4.646,1.094 5.104,1.323 0.458,0.229 10 false HT1B 4.646,1.74 5.104,1.969 0.458,0.229 10 false OX1B 5.271,1.083 5.729,1.313 0.458,0.229 10 false HT1B 5.271,1.74 5.729,1.969 0.458,0.229 10 false OX1B 5.281,2.323 5.667,2.521 0.385,0.198 10 false E2 5.281,2.958 5.74,3.188 0.458,0.229 10 false MREL



DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0037 Oxygen Sensor Heater Control Circuit Low (Bank 1 Sensor 2) The heated oxygen sensor heater (for bank 1, 2 sensor 2) current is below 0.3 A (1 trip detection logic).
·

Open in heated oxygen sensor heater (for bank 1 sensor 2) circuit

·

Heated oxygen sensor heater (for bank 1 sensor 2)

·

No. 1 integration relay (MAIN relay)

·

ECM


Comes on DTC stored
P0038 Oxygen Sensor Heater Control Circuit High (Bank 1 Sensor 2) The heated oxygen sensor heater (for bank 1, 2 sensor 2) current is higher than 2 A (1 trip detection logic).
·

Short in heated oxygen sensor heater (for bank 1 sensor 2) circuit

·

Heated oxygen sensor heater (for bank 1 sensor 2)

·

No. 1 integration relay (MAIN relay)

·

ECM


Comes on DTC stored
P0057 Oxygen Sensor Heater Control Circuit Low (Bank 2 Sensor 2) The heated oxygen sensor heater (for bank 1, 2 sensor 2) current is below 0.3 A (1 trip detection logic).
·

Open in heated oxygen sensor heater (for bank 1, 2 sensor 2) circuit

·

Heated oxygen sensor heater (for bank 2 sensor 2)

·

No. 1 integration relay (MAIN relay)

·

ECM


Comes on DTC stored
P0058 Oxygen Sensor Heater Control Circuit High (Bank 2 Sensor 2) The heated oxygen sensor heater (for bank 1, 2 sensor 2) current is higher than 2 A (1 trip detection logic).
·

Short in heated oxygen sensor heater (for bank 1, 2 sensor 2) circuit

·

Heated oxygen sensor heater (for bank 2 sensor 2)

·

No. 1 integration relay (MAIN relay)

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

The sensing portion of the heated oxygen sensor has a zirconia element which is used to detect the oxygen concentration in the exhaust gas. If the zirconia element is at the appropriate temperature, and the difference between the oxygen concentrations surrounding the inside and outside surfaces of the sensor is large, the zirconia element generates voltage signals. In order to increase the oxygen concentration detecting capacity of the zirconia element, the ECM supplements the heat from the exhaust with heat from a heating element inside the sensor.

The ECM monitors the current applied to the heated oxygen sensor heater to check the heater for malfunctions. If the current is below the threshold value, the ECM will determine that there is an open circuit in the heater. If the current is above the threshold value, the ECM will determine that there is a short circuit in the heater.

Example:

The ECM stores DTC P0038 or P0058 when the current in the heated oxygen sensor heater is higher than 2 A. Conversely, when the heater current is below 0.3 A, DTC P0037 or P0057 is stored.



CONFIRMATION DRIVING PATTERN

A198819
0.781,1.021 1.427,1.219 0.646,0.198 10 false 3000 rpm 1.031,1.75 1.438,1.948 0.406,0.198 10 false Idling 0.229,2.042 1.479,2.25 1.25,0.208 10 false Ignition Switch ON 1.927,2.177 2.167,2.344 0.24,0.167 10 false [A] 2.781,1.635 2.979,1.833 0.198,0.198 10 false [B] 4.021,0.885 4.292,1.104 0.271,0.219 10 false [C] 5.385,1.604 5.604,1.781 0.219,0.177 10 false [D] 2.271,2.594 3.469,2.792 1.198,0.198 10 false 5 minutes or more 4.875,2.604 6.052,2.823 1.177,0.219 10 false 5 minutes or more 3.854,2.615 4.438,2.813 0.583,0.198 10 false 1 minute 5.979,3.031 6.177,3.229 0.198,0.198 10 false [E]

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the tester on [A].

6.

Start the engine and idle it for 5 minutes or more [B].

7.

With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of 3000 rpm for 1 minute [C].

8.

Idle the engine for 5 minutes or more [D].

9.

Enter the following menus: Powertrain / Engine and ECT / DTC [E].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P0037, P0038, P0057 or P0058.

13.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [E] again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Bank 1 refers to the bank that includes No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include No. 1 cylinder.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.



PROCEDURE

1.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)

Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (+B OF HEATED OXYGEN SENSOR)

NG

2.CHECK TERMINAL VOLTAGE (+B OF HEATED OXYGEN SENSOR)
a.
A149595
0.219,1.573 0.635,1.844 0.417,0.271 0.219,1.906 0.635,2.177 0.417,0.271 1.958,1.823 2.323,1.531 true 0.104,0.104 0.302,0.281 0.198,0.177 10 *a 0.708,1.646 0.906,1.823 0.198,0.177 10 *A 0.698,1.969 0.896,2.146 0.198,0.177 10 *B 0.313,1.635 0.635,1.813 0.323,0.177 10 C88 0.26,1.948 0.75,2.135 0.49,0.188 10 C152 2.375,1.438 2.635,1.615 0.26,0.177 10 +B
*A for Bank 1
*B for Bank 2
*a Front view of wire harness connector
(to Heated Oxygen Sensor)


Disconnect the heated oxygen sensor connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C88-2 (+B) - Body ground Ignition switch ON 11 to 14 V
C152-2 (+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)

NG

5.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - NO. 1 INTEGRATION RELAY)
3.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)
a.

Disconnect the heated oxygen sensor connectors.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C88-1 (HT1B) - C129-1 (HT1B) Always Below 1 Ω
C152-1 (HT2B) - C130-5 (HT2B) Always Below 1 Ω
C88-1 (HT1B) or C129-1 (HT1B) - Body ground Always 10 kΩ or higher
C152-1 (HT2B) or C130-5 (HT2B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK WHETHER DTC OUTPUT RECURS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

d.

Turn the ignition switch off and wait for at least 30 seconds.


e.

Start the engine.


f.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


g.

Enter the following menus: Powertrain / Engine and ECT / DTC / Pending.

Powertrain > Engine > Trouble Codes
50001 61

h.

Read the pending DTCs.

Result:
Result Proceed to
DTC is not output A
P0037, P0038, P0057 or P0058 is output B




A

B

5.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - NO. 1 INTEGRATION RELAY)
a.

Disconnect the heated oxygen sensor connectors.


b.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C88-2 (+B) - 1J-5 Always Below 1 Ω
C152-2 (+B) - 1J-5 Always Below 1 Ω
C88-2 (+B) or 1J-5 - Body ground Always 10 kΩ or higher
C152-2 (+B) or 1J-5 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR