Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM › from 2012.10
RM1840EF _51 Engine / Hybrid System _009572 1GR-FE ENGINE CONTROL _0052127 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0724  Brake Switch "B" Circuit High  


DESCRIPTION

The stop light switch assembly is a duplex system that transmits 2 signals: STP and ST1-. These 2 signals are used by the ECM to monitor whether or not the brake system is working properly.

This DTC indicates that the stop light switch assembly remains on. When the stop light switch assembly remains on during GO and STOP driving, the ECM interprets this as a fault in the stop light switch assembly. Then the MIL illuminates and the ECM stores the DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0724 Brake Switch "B" Circuit High The stop light switch remains on even when vehicle is driven in a GO (30 km/h (18.63 mph) or more) and STOP (less than 3 km/h (1.86 mph)) pattern 5 times (2 trip detection logic).
·

Short in stop light switch signal circuit

·

Stop light switch assembly

·

ECM


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

A199312
1.417,2.052 1.802,2.281 0.385,0.229 10 false Idling 0.604,2.396 1.875,2.719 1.271,0.323 10 false Ignition Switch ON 2.49,2.5 2.688,2.698 0.198,0.198 10 false [A] 2.583,3.083 3.292,3.229 0.708,0.146 10 false 5 seconds 3.271,3.49 3.479,3.667 0.208,0.177 10 false [B] 3.406,1.917 3.615,2.094 0.208,0.177 10 false [C] 6.729,3.479 6.927,3.677 0.198,0.198 10 false [E] 4.042,1.5 4.25,1.677 0.208,0.177 10 false [D] 0.479,1.229 1.823,1.417 1.344,0.188 10 false 30 km/h (18.65 mph) 0.635,1.76 1.875,1.969 1.24,0.208 10 false 3 km/h (1.86 mph)

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the tester on [A].

6.

Wait 5 seconds.

7.

Enter the following menus: Powertrain / Engine and ECT / DTC [B].

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P0724.

11.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [C] through [E].



12.

Start the engine [C].

13.

Accelerate the vehicle to 30 km/h (19 mph) or more, and then depress the brake pedal and decelerate the vehicle to 3 km/h (1.8 mph) or less [D]. Repeat step [D] 5 times.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


14.

Check the DTC judgment result [E].


WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:
·

Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

·

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Stop Light Switch.

Powertrain > Engine > Data List
Tester Display
Stop Light Switch
50003 61 188

e.

Read the value displayed on the tester when the brake pedal is depressed and released.

OK:
Brake Pedal Display
Released OFF
Depressed ON



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT STOP LIGHT SWITCH ASSEMBLY (RESISTANCE)
2.INSPECT STOP LIGHT SWITCH ASSEMBLY (RESISTANCE)
a.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (ECM - STOP LIGHT SWITCH ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (ECM - STOP LIGHT SWITCH ASSEMBLY)
a.
A112419
2.667,2.448 3.042,2.698 0.375,0.25 2.719,3.406 3.104,4.073 true 0.875,0.146 1.063,0.365 0.188,0.219 10 false *a 0.292,2.031 0.479,2.24 0.188,0.208 10 false *c 2.479,0.167 2.667,0.375 0.188,0.208 10 false *b 2.74,4.073 3.417,4.302 0.677,0.229 10 false 15 (STP) 2.688,2.49 3.26,2.688 0.573,0.198 10 false G155
*1 Brake Pedal Depressed
*2 Brake Pedal Released
*a Component with harness connected
(to ECM)


Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G155-15 (STP) - Body ground Brake pedal depressed 11 to 14 V
Brake pedal released Below 3.0 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR