Home › Engine / Hybrid System › 2TR-FE ENGINE CONTROL › SFI SYSTEM(w/ Secondary Air Injection System) › from 2012.10
RM1840EF _51 Engine / Hybrid System _009569 2TR-FE ENGINE CONTROL _0052076 SFI SYSTEM(w/ Secondary Air Injection System) C

2TR-FE ENGINE CONTROL  SFI SYSTEM(w/ Secondary Air Injection System)  P0011  Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 1)  P0012  Camshaft Position "A" - Timing Over-Retarded (Bank 1)  


DESCRIPTION

The VVT system includes the ECM, camshaft timing oil control valve and camshaft timing gear. The ECM sends a target duty cycle control signal to the camshaft timing oil control valve. This control signal regulates the oil pressure supplied to the camshaft timing gear. Camshaft timing control is performed according to engine operating conditions such as the intake air volume, throttle valve position and engine coolant temperature. The ECM controls the camshaft timing oil control valve based on the signals transmitted by several sensors. The camshaft timing gear regulates the intake camshaft angle using oil pressure through the camshaft timing oil control valve. As a result, the relative positions of the camshaft and crankshaft are optimized, the engine torque and fuel economy improve, and the exhaust emissions decrease under overall driving conditions. The ECM detects the actual intake valve timing using signals from the camshaft and crankshaft position sensors and performs feedback control. This is how the target intake valve timing is verified by the ECM.

A192077E53
2.563,4.573 2.844,4.271 2.844,4.271 3.604,4.271 false 3.177,4.813 3.323,5.042 3.323,5.042 3.854,5.042 false 4.479,0.854 6.146,1.021 1.667,0.167 10 false Camshaft Position Sensor 4.479,1.354 6.208,1.51 1.729,0.156 10 false Crankshaft Position Sensor 0.115,0.052 1.667,0.302 1.552,0.25 10 false VVT System: 2.333,1.958 3.615,2.135 1.281,0.177 10 false Target Valve Timing 2.333,1.292 3.615,1.469 1.281,0.177 10 false Actual Valve Timing 2.688,2.698 3.406,2.875 0.719,0.177 10 false Correction 2.823,3.208 3.229,3.385 0.406,0.177 10 false ECM 1.604,3.771 3.813,3.948 2.208,0.177 10 false Camshaft Timing Oil Control Valve 0.177,2.719 0.875,2.896 0.698,0.177 10 false Duty Cycle 4.479,1.865 5.802,2.021 1.323,0.156 10 false Mass Air Flow Meter 4.479,2.885 6.823,3.073 2.344,0.188 10 false Engine Coolant Temperature Sensor 4.479,2.385 6.031,2.552 1.552,0.167 10 false Throttle Position Sensor 4.479,3.396 5.938,3.552 1.458,0.156 10 false Vehicle Speed Sensor 0.313,4.271 1.677,4.479 1.365,0.208 10 false Engine Oil Pressure 3.656,4.188 5.094,4.375 1.438,0.188 10 false Camshaft Timing Gear 3.896,4.979 5,5.24 1.104,0.26 10 false Intake Camshaft

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0011 Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 1) Intake valve timing is stuck at a certain value when in the advance range (1 trip detection logic).
·

Mechanical system (Timing chain has jumped tooth or chain stretched)

·

Camshaft timing oil control valve assembly

·

Oil control valve filter

·

Camshaft timing gear assembly

·

ECM


Comes on DTC stored
P0012 Camshaft Position "A" - Timing Over-Retarded (Bank 1) Intake valve timing is stuck at a certain value when in the retard range (2 trip detection logic).
·

Mechanical system (Timing chain has jumped tooth or chain stretched)

·

Camshaft timing oil control valve assembly

·

Oil control valve filter

·

Camshaft timing gear assembly

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

The ECM optimizes the intake valve timing using the VVT (Variable Valve Timing) system to control the intake camshaft. The VVT system includes the ECM, camshaft timing oil control valve and camshaft timing gear. The ECM sends a target duty cycle control signal to the camshaft timing oil control valve. This control signal regulates the oil pressure supplied to the camshaft timing gear. The camshaft timing gear can advance or retard the intake camshaft.

If the difference between the target and actual intake valve timing is large, and changes in the actual intake valve timing are small, the ECM interprets this as a camshaft timing gear being stuck and stores a DTC.


Example:

A DTC is stored when the following conditions 1 and 2 are met:

1. It takes 5 seconds or more to change the valve timing by 5°CA.

2. After condition 1 is met, the camshaft timing oil control valve is forcibly activated 63 times or more (when the vehicle is idling, this takes approximately 100 seconds).


These DTCs indicate that the camshaft timing gear cannot operate properly due to camshaft timing oil control valve malfunctions or the presence of foreign objects in the camshaft timing oil control valve.


MONITOR STRATEGY

Required Sensors/Components (Main) Camshaft timing oil control valve assembly and Camshaft timing gear assembly
Required Sensors/Components (Related) Crankshaft position sensor, Camshaft position sensor and Engine coolant temperature sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

A232050E54
6.719,2.635 6.333,3.5 6.333,3.5 6.25,3.5 false 4.146,2.656 3.823,3.521 3.823,3.521 3.76,3.521 false 1.365,2.354 1.594,2.583 0.229,0.229 10 false [A] 1.875,2.031 2.094,2.271 0.219,0.24 10 false [B] 3.01,1 3.229,1.219 0.219,0.219 10 false [C] 4.052,2.313 4.281,2.521 0.229,0.208 10 false [D] 4.26,3.135 4.49,3.375 0.229,0.24 10 false [E] 5.448,2.219 5.698,2.448 0.25,0.229 10 false [F]* 6.615,2.302 6.854,2.448 0.24,0.146 10 false [G] 6.813,3.156 7.031,3.375 0.219,0.219 10 false [H] 0.146,2.302 1.125,2.719 0.979,0.417 10 false Ignition Switch ON 0.708,2.063 1.094,2.302 0.385,0.24 10 false Idling 0.052,1.104 1.146,1.521 1.094,0.417 10 false Approximately 60 km/h (37 mph) 0.167,0.375 1.156,0.604 0.99,0.229 10 false Vehicle Speed 1.615,2.771 2.469,3.021 0.854,0.25 10 false Warming up 2.573,2.771 3.823,3.01 1.25,0.24 10 false 10 minutes or more 2.552,3.427 3.844,3.604 1.292,0.177 10 false 3 minutes or more 2.375,0.021 7.073,0.604 4.698,0.583 10 false *: Repeat the pattern of accelerating the vehicle from rest to approximately 60 km/h (37 mph) (depress the accelerator pedal by a large amount) and then decelerating the vehicle 10 to 15 times. 5,3.406 6.188,3.583 1.188,0.177 10 false 3 minutes or more

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the intelligent tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the intelligent tester on [A].

6.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].

7.

Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


8.

Idle the engine for 3 minutes or more [D].

9.

Enter the following menus: Powertrain / Engine and ECT / DTC [E].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P0011 or P0012.

13.

Check the DTC judgment result.

Intelligent Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [F] through [H].



14.

Repeat the pattern of accelerating the vehicle from rest to approximately 60 km/h (37 mph) and then decelerating the vehicle 10 to 15 times [F].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Depress the accelerator pedal by a large amount.


15.

Idle the engine for 3 minutes or more [G].

16.

Enter the following menus: Powertrain / Engine and ECT / DTC [H].

17.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



18.

Check the DTC judgment result again.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.




CAUTION / NOTICE / HINT

HINT:

DTC P0011 or P0012 may be stored when foreign objects in the engine oil are caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. Foreign objects are filtered out by the oil filter.


HINT:
Timing Over-advanced
(Valve Timing is Out of Specified Range)
Timing Over-retarded
(Valve Timing is Out of Specified Range)
P0011 P0012

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0011 OR P0012)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

e.

Read the DTCs.

Result:
Result Proceed to
P0011 or P0012 is output A
P0011 or P0012 and other DTCs are output B


HINT:

If any DTCs other than P0011 or P0012 are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OPERATE CAMSHAFT TIMING OIL CONTROL VALVE)

B

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OPERATE CAMSHAFT TIMING OIL CONTROL VALVE)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the intelligent tester on.


d.

Warm up the engine.


e.

Turn the A/C on.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Linear (Bank 1).

Powertrain > Engine > Active Test
Tester Display
Control the VVT Linear (Bank1)
50004 61 32

g.

Check the engine speed while operating the camshaft timing oil control valve using the intelligent tester.

OK:
Intelligent Tester Operation Specified Condition
0% Normal engine speed
100% Engine idles roughly or stalls


HINT:

Refer to "Data List / Active Test" [VVT OCV Duty #1 and VVT Change Angle #1].

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM(w/ Secondary Air Injection System)>DATA LIST / ACTIVE TEST



Result:
Proceed to
OK
NG



OK

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0011 OR P0012)

NG

4.CHECK VALVE TIMING (CHECK FOR LOOSENESS IN TIMING CHAIN AND WHETHER TIMING CHAIN HAS JUMPED TOOTH)
3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0011 OR P0012)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

e.

Start the engine and warm it up.


f.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


g.

Read the output pending DTCs using the intelligent tester.

Powertrain > Engine > Trouble Codes
50001 61
OK:

No pending DTC output.



Result:
Proceed to
OK
NG



OK

NG

4.CHECK VALVE TIMING (CHECK FOR LOOSENESS IN TIMING CHAIN AND WHETHER TIMING CHAIN HAS JUMPED TOOTH)
4.CHECK VALVE TIMING (CHECK FOR LOOSENESS IN TIMING CHAIN AND WHETHER TIMING CHAIN HAS JUMPED TOOTH)
a.
A301841C01
0.854,2.448 0.656,2.135 0.656,2.135 2.427,2.49 true 2.469,2.688 2.729,2.323 true 2.708,1.01 2.25,0.292 2.25,0.292 2.698,0.802 true 1.844,4.052 2.583,3.885 true 1.01,0.938 1.063,1.406 1.063,1.406 1.063,0.708 true 2.083,0.208 2.396,0.365 0.313,0.156 10 false *1 0.49,2.042 0.802,2.198 0.313,0.156 10 false *1 2.635,2.135 3.313,2.396 0.677,0.26 10 false 6°37' 0.25,0.188 0.698,0.427 0.448,0.24 10 false 13°47' 2.625,3.802 2.938,3.958 0.313,0.156 10 false *1 1.01,1.406 1.323,1.563 0.313,0.156 10 false *1
*1 Timing Mark


Remove the cylinder head cover.


b.

Turn the crankshaft to align the timing marks of the crankshaft.


c.

Align the groove of the crankshaft pulley with the "0" position.


d.

Confirm whether the timing marks of the camshaft pulley and cylinder head cover are facing each other.

HINT:

If the timing marks are not as shown, turn the crankshaft one revolution clockwise.


OK:

The timing marks of the camshaft pulley and the cylinder head cover face each other when the groove of the crankshaft pulley is in the "0" position.



Result:
Proceed to
OK
NG



OK

5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

NG

5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
a.

Inspect the camshaft timing oil control valve assembly.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>CAMSHAFT OIL CONTROL VALVE>INSTALLATION


Result:
Proceed to
OK
NG



OK

6.INSPECT OIL CONTROL VALVE FILTER

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

6.INSPECT OIL CONTROL VALVE FILTER
a.

Remove the oil control valve filter.

Click hereEngine / Hybrid System>2TR-FE ENGINE MECHANICAL>ENGINE UNIT>DISASSEMBLY


b.

Check that the filter is not clogged.

OK:

Filter is not clogged.



Result:
Proceed to
OK
NG



OK

7.REPLACE CAMSHAFT TIMING GEAR ASSEMBLY

NG

CLEAN OR REPLACE OIL CONTROL VALVE FILTER

7.REPLACE CAMSHAFT TIMING GEAR ASSEMBLY
a.

Replace the camshaft timing gear assembly.

Click hereEngine / Hybrid System>2TR-FE ENGINE MECHANICAL>CAMSHAFT>REMOVAL


Result:
Proceed to
NEXT



NEXT

8.CHECK WHETHER DTC OUTPUT RECURS
8.CHECK WHETHER DTC OUTPUT RECURS
a.

Perform the Confirmation Driving Pattern.

OK:

No pending DTC is output and All Readiness is NORMAL.


HINT:

DTC P0011 or P0012 is stored when foreign objects in the engine oil are caught in some parts of the system. These codes will remain stored even if the system returns to normal after a short time. These foreign objects are then captured by the oil filter, thus eliminating the source of the problem.



Result:
Proceed to
OK
NG



OK

END

NG