Home › Engine / Hybrid System › 2TR-FBE ENGINE CONTROL › SFI SYSTEM › from 2012.10
RM1840EF _51 Engine / Hybrid System _009571 2TR-FBE ENGINE CONTROL _0052126 SFI SYSTEM C

2TR-FBE ENGINE CONTROL  SFI SYSTEM  P0335  Crankshaft Position Sensor "A" Circuit  P0339  Crankshaft Position Sensor "A" Circuit Intermittent  


DESCRIPTION

The crankshaft position sensor system consists of a crankshaft position sensor plate and pickup coil. The sensor plate has 34 teeth, with 2 teeth missing for detecting TDC, and is installed on the crankshaft. The crankshaft position sensor generates 34 signals per crankshaft revolution. The ECM determines the cylinder status based on the G2 signals and detects the crankshaft angle and engine speed from the NE signals.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0335 Crankshaft Position Sensor "A" Circuit Either condition is met:
·

No crankshaft position sensor signal is sent to the ECM while cranking (1 trip detection logic).

·

No crankshaft position sensor signal is sent to the ECM at an engine speed of 600 rpm or more (1 trip detection logic).


·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

Crankshaft position sensor plate

·

Camshaft position sensor

·

ECM


Comes on DTC stored
P0339 Crankshaft Position Sensor "A" Circuit Intermittent Under conditions (a), (b) and (c), no crankshaft position sensor signal is sent to the ECM for 0.05 seconds or more (1 trip detection logic):
(a) The engine speed is 1000 rpm or more.
(b) The starter signal is off.
(c) 3 seconds or more have elapsed since the starter signal switched from on to off.
·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

Crankshaft position sensor plate

·

ECM


- DTC stored

A063955
2.792,0.594 3.24,0.906 0.448,0.313 10 false GND 2.802,1.427 3.24,1.75 0.438,0.323 10 false GND 0.042,0.042 0.656,0.24 0.615,0.198 10 false 5 V/DIV. 0.208,0.573 0.604,0.76 0.396,0.188 10 false CH1 0.198,1.354 0.583,1.542 0.385,0.188 10 false CH2 1.688,1.917 2.667,2.115 0.979,0.198 10 false 20 msec./DIV.

Reference: Inspection using an oscilloscope

HINT:
·

The correct waveforms are as shown.

·

G2 is the camshaft position sensor signal, and NE+ is the crankshaft position sensor signal.

·

Grounding failure of the shielded wire may cause noise in the waveforms.

Item Content
ECM Terminal Name CH1: G2 - NE-
CH2: NE+ - NE-
Tester Range 5 V/DIV.
20 ms./DIV.
Condition Idling with warm engine




WIRING DIAGRAM

A225774
6.125,0.542 6.438,0.802 0.313,0.26 10 false G2 5.781,0.479 6.135,0.781 0.354,0.302 10 false 11 5.823,1.135 6.021,1.292 0.198,0.156 10 false 5 6.094,3.115 6.5,3.344 0.406,0.229 10 false NE+ 6.094,1.438 6.531,1.688 0.438,0.25 10 false NE- 5.781,3.01 6.01,3.229 0.229,0.219 10 false 12 6.375,5.146 6.854,5.427 0.479,0.281 10 false ECM 2.479,0.75 2.583,0.906 0.104,0.156 10 false 1 2.479,1.208 2.656,1.458 0.177,0.25 10 false 2 2.469,2.646 2.573,2.802 0.104,0.156 10 false 2 2.469,3.094 2.635,3.333 0.167,0.24 10 false 1 0.99,1.594 1.302,1.823 0.313,0.229 10 false C68 0.99,1.74 2.802,2.01 1.813,0.271 10 false Camshaft Position Sensor 0.844,3.865 1.146,4.083 0.302,0.219 10 false C6 0.844,4 2.583,4.271 1.74,0.271 10 false Crankshaft Position Sensor 2.771,4.281 3.448,4.51 0.677,0.229 10 false Shielded 2.104,2.656 2.51,2.906 0.406,0.25 10 false NE- 2.073,3.094 2.479,3.344 0.406,0.25 10 false NE+ 2.479,3.448 2.656,3.646 0.177,0.198 10 false 3 2,3.531 2.438,3.792 0.438,0.26 10 false GND 5.75,0.667 6.156,0.875 0.406,0.208 10 false C96 5.75,1.323 6.156,1.573 0.406,0.25 10 false C96 3.458,1.615 4.167,1.823 0.708,0.208 10 false Shielded 5.75,3.198 6.167,3.458 0.417,0.26 10 false C96

CAUTION / NOTICE / HINT

Before inspecting the crankshaft position sensor, perform the following inspections which concern the camshaft position sensor.

·

Check that the camshaft position sensor connector is securely connected, is not loose, does not rattle, etc.

·

Check that the camshaft position sensor is not loose, does not rattle, etc.

·

Check that the camshaft timing gear is installed properly.

·

Perform the Active Test under the conditions* from the time the noise occurred described by the customer (for example, while driving the vehicle) and check if the noise stops.

HINT:

*: Some examples of conditions are idling, racing the engine and driving at full throttle.



HINT:
·

Troubleshoot for DTCs P0335 and P0339 first. If the trouble area cannot be determined, there may be a mechanical malfunction.

·

Check the engine speed. The engine speed can be checked by using the intelligent tester. Follow the procedure below:

1.

Connect the intelligent tester to the DLC3.

2.

Start the engine.

3.

Turn the tester on.

4.

Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.


The engine speed may be indicated as zero despite the crankshaft revolving normally. This is caused by a lack of NE signals from the crankshaft position sensor. Alternatively, the engine speed may be indicated as lower than the actual engine speed if the crankshaft position sensor output voltage is insufficient.


·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.

Powertrain > Engine and ECT > Data List
Tester Display
Engine Speed
50003 234 9

e.

Start the engine.


f.

Read the values displayed on the tester while the engine is running.

OK:

Correct values are displayed.


HINT:
·

To check the engine speed change, display the graph on the tester.

·

If the engine does not start, check the engine speed while cranking.

·

If the engine speed indicated on the tester remains at zero (0), there may be an open or short in the crankshaft position sensor circuit.




Result:
Proceed to
OK
NG



OK

NG

2.INSPECT CRANKSHAFT POSITION SENSOR (RESISTANCE)
2.INSPECT CRANKSHAFT POSITION SENSOR (RESISTANCE)
a.

Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

NG

3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
a.

Disconnect the crankshaft position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C6-1 (NE+) - C96-12 (NE+) Always Below 1 Ω
C6-2 (NE-) - C96-5 (NE-) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C6-1 (NE+) or C96-12 (NE+) - Body ground Always 10 kΩ or higher
C6-2 (NE-) or C96-5 (NE-) - Body ground Always 10 kΩ or higher



d.

Reconnect the ECM connector.


e.

Reconnect the crankshaft position sensor connector.


Result:
Proceed to
OK
NG



OK

4.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

4.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)
a.
A208464
0.458,1.677 0.771,1.875 0.313,0.198 10 false OK 2.677,1.781 2.99,1.979 0.313,0.198 10 false NG 1.74,1.552 2.406,1.792 0.667,0.24 10 false Clearance

Check the crankshaft position sensor installation condition.

OK:

Sensor is installed correctly.



Result:
Proceed to
OK
NG



OK

5.CHECK CRANKSHAFT POSITION SENSOR PLATE (TEETH OF SENSOR PLATE)

NG

SECURELY REINSTALL CRANKSHAFT POSITION SENSOR

5.CHECK CRANKSHAFT POSITION SENSOR PLATE (TEETH OF SENSOR PLATE)
a.

Check the teeth of the sensor plate.

OK:

Sensor plate teeth do not have any cracks or deformation.



Result:
Proceed to
OK
NG



OK

NG

REPLACE CRANKSHAFT POSITION SENSOR PLATE