Home › Engine / Hybrid System › 2TR-FBE ENGINE CONTROL › SFI SYSTEM › from 2012.10
RM1840EF _51 Engine / Hybrid System _009571 2TR-FBE ENGINE CONTROL _0052126 SFI SYSTEM C

2TR-FBE ENGINE CONTROL  SFI SYSTEM  P0420  Catalyst System Efficiency Below Threshold (Bank 1)  


DESCRIPTION

The ECM uses sensors mounted in front of and behind the Three Way Catalytic Converter (TWC) to monitor its efficiency.

The first sensor, the air fuel ratio sensor, sends pre-catalyst information to the ECM. The second sensor, the heated oxygen sensor, sends post-catalyst information to the ECM.

In order to detect any deterioration in the TWC, the ECM calculates the Oxygen Storage Capacity (OSC) of the TWC. This calculation is based on the voltage output of the heated oxygen sensor while performing active air fuel ratio control.

The OSC value is an indication of the oxygen storage capacity of the TWC. When the vehicle is being driven with a warm engine, active air fuel ratio control is performed for approximately 15 to 20 seconds. When it is performed, the ECM deliberately sets the air fuel ratio to lean or rich levels. If the rich-lean cycle of the heated oxygen sensor is long, the OSC becomes greater. There is a direct correlation between the OSCs of the heated oxygen sensor and the TWC.

The ECM uses the OSC value to determine the state of the TWC. If any deterioration has occurred, it illuminates the MIL and stores the DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0420 Catalyst System Efficiency Below Threshold (Bank 1) The Oxygen Storage Capacity (OSC) value is less than the standard value under active air fuel ratio control (2 trip detection logic).
·

Front exhaust pipe assembly (TWC: Front catalyst and rear catalyst)

·

Gas leak from exhaust system

·

Air fuel ratio sensor

·

Heated oxygen sensor


Comes on DTC stored

CATALYST LOCATION

A242742
0.438,1.833 0.615,1.042 false 0.615,1.042 0.833,1.042 false 0.969,1.781 1.115,1.49 false 1.115,1.49 1.26,1.49 false 2.146,2.354 2.438,2.604 false 2.438,2.604 2.76,2.604 false 2.646,2.083 3.01,1.156 false 3.01,1.156 3.292,1.156 false 4.646,1.865 4.958,2.281 false 4.958,2.281 5.5,2.281 false 5.656,0.844 5.458,0.542 false 5.458,0.542 4.938,0.542 false 1.302,2.49 1.198,2.844 false 1.198,2.844 0.958,2.844 false 2.094,2.875 2.292,3.417 false 2.292,3.417 2.448,3.417 false 0.875,0.969 1.125,1.146 0.25,0.177 10 false *1 1.302,1.427 1.552,1.604 0.25,0.177 10 false *2 0.792,2.76 1.042,2.938 0.25,0.177 10 false *3 3.313,1.063 3.563,1.24 0.25,0.177 10 false *5 2.813,2.542 3.063,2.719 0.25,0.177 10 false *4 2.479,3.333 2.729,3.51 0.25,0.177 10 false *6 5.542,2.198 5.792,2.375 0.25,0.177 10 false *7 4.771,0.469 5.021,0.646 0.25,0.177 10 false *8
*1 Exhaust Manifold *2 Air Fuel Ratio Sensor
*3 TWC: Front Catalyst *4 TWC: Rear Catalyst
*5 Front Exhaust Pipe Assembly *6 Heated Oxygen Sensor
*7 Center Exhaust Pipe Assembly *8 Tailpipe Assembly


CONFIRMATION DRIVING PATTERN

HINT:

Performing this confirmation driving pattern will activate the catalyst monitor. This is very useful for verifying the completion of a repair.


A250593
2.448,2.156 2.74,0.219 false 2.74,0.219 2.865,0.219 false 1.875,3.042 2.75,3.333 0.875,0.292 10 false Warming up 2.719,3.042 4,3.333 1.281,0.292 10 false 20 minutes or more 4.063,3.042 5.365,3.292 1.302,0.25 10 false 10 minutes or more 0.156,2.375 1.417,2.646 1.26,0.271 10 false Ignition Switch ON 0.979,2.094 1.406,2.375 0.427,0.281 10 false Idling 0.229,1.406 1.438,1.677 1.208,0.271 10 false 60 km/h (37 mph) 0.229,0.958 1.438,1.229 1.208,0.271 10 false 64 km/h (40 mph) 0.156,0.469 1.406,0.781 1.25,0.313 10 false 113 km/h (70 mph) 0.458,0.115 1.375,0.385 0.917,0.271 10 false Vehicle Speed 1.656,2.448 2,2.75 0.344,0.302 10 false [A] 2.177,1.938 2.417,2.167 0.24,0.229 10 false [B] 3.219,1.063 3.5,1.292 0.281,0.229 10 false [C] 4.74,0.563 5.01,0.781 0.271,0.219 10 false [D] 2.906,0.135 4.74,0.521 1.833,0.385 10 false Engine coolant temperature is 75°C or more 5.177,0.073 6.583,0.281 1.406,0.208 10 false NOTICE: 1.271,3.385 6.208,3.656 4.938,0.271 10 false (Note: Even if vehicle stops during driving pattern, test can be resumed) 5.188,0.26 7.115,1.104 1.927,0.844 10 false This test will not be completed if the vehicle is driven at an absolutely constant speed, such as with cruise control activated.

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the intelligent tester on [A].

3.

Enter the following menus: Powertrain / Engine and ECT / DTC / Clear.

4.

Clear DTCs (if output).

5.

Enter the following menus: Powertrain / Engine and ECT / Data List / Catalyst Monitor.

6.

Check that Catalyst Monitor is Incomplete.

7.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [B].

8.

Drive the vehicle at 60 km/h (37 mph) or more for 20 minutes or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:
·

This step is performed to complete ethanol concentration learning.

·

If DTC P0420 is output when any of the following conditions is met, it is necessary to complete ethanol concentration learning to meet preconditions.

·

The battery has been disconnected and reconnected.

·

The DTCs have been cleared.

·

Both fuel tank assemblies (main and sub tanks) have been filled with fuel.




9.

Drive the vehicle at a speed between 64 km/h and 113 km/h (40 mph and 70 mph) for at least 10 minutes [D].

10.

The monitor items will change to complete as Catalyst Monitor operates.

11.

Enter the following menus: Powertrain / Engine and ECT / DTC / Pending; then check if any DTCs (any pending DTCs) are output.


HINT:

If Catalyst Monitor does not change to complete and no pending DTCs are stored, extend the driving time.


CONDITIONING FOR SENSOR TESTING

HINT:

Perform the operation with the engine speeds and time durations described below prior to checking the waveforms of the air fuel ratio and heated oxygen sensors. This is in order to activate the sensors sufficiently to obtain the appropriate inspection results.


A302570
4.885,3.094 5.031,3.313 5.031,3.313 5.167,3.083 false 0.521,0.625 1.51,0.885 0.99,0.26 10 false Engine Speed 0.813,1.042 1.531,1.333 0.719,0.292 10 false 3000 rpm 0.823,1.583 1.542,1.875 0.719,0.292 10 false 2000 rpm 1.083,2.531 1.531,2.854 0.448,0.323 10 false Idling 0.333,2.781 1.688,3.021 1.354,0.24 10 false Ignition Switch off 1.656,2.656 1.906,2.938 0.25,0.281 10 false (a) 2.094,2.417 2.344,2.698 0.25,0.281 10 false (b) 3.677,0.906 3.927,1.188 0.25,0.281 10 false (c) 4.781,0.906 5.031,1.188 0.25,0.281 10 false (d) 5.094,1.458 5.344,1.74 0.25,0.281 10 false (d) 6.594,2.75 7.042,3.073 0.448,0.323 10 false Time 4.719,3.302 5.438,3.583 0.719,0.281 10 false 2 seconds 5.167,3.531 5.677,3.729 0.51,0.198 10 false Check 2.104,3.24 2.979,3.5 0.875,0.26 10 false Warming up 3.323,3.25 4.542,3.49 1.219,0.24 10 false At least 3 minutes

(a) Connect the intelligent tester to the DLC3.

(b) Start the engine and warm it up with all the accessories switched off until the engine coolant temperature stabilizes.

(c) Run the engine at an engine speed of between 2500 rpm and 3000 rpm for at least 3 minutes.

(d) While running the engine at 3000 rpm and 2000 rpm alternating at 2 second intervals, check the waveforms of the air fuel ratio and heated oxygen sensors using the tester.


HINT:
·

If the voltage output of the air fuel ratio or heated oxygen sensor does not fluctuate, or there is noise in the waveform of either sensor, the sensor may be malfunctioning.

·

If the voltage outputs of both sensors remain lean or rich, the air fuel ratio may be extremely lean or rich. In such cases, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F sensor.

·

If the Three Way Catalytic Converter (TWC) has deteriorated, the heated oxygen sensor (located behind the TWC) voltage output fluctuates up and down frequently, even under normal driving conditions (active air fuel ratio control is not performed).



A121610
0.07,0.054 3.97,0.23 3.9,0.176 10 Voltage output when active air fuel ratio control not performed: 2.374,0.421 3.448,0.601 1.074,0.18 10 Normal Catalyst 4.744,0.426 6.098,0.601 1.354,0.174 10 Deteriorated Catalyst 0.257,2.118 1.244,2.826 0.988,0.708 10 Waveform of Heated Oxygen Sensor behind TWC 0.257,0.653 1.331,1.298 1.075,0.644 10 Waveform of Air Fuel Ratio Sensor in front of TWC 1.446,0.789 1.824,0.938 0.378,0.148 10 3.5 V 1.446,1.123 1.845,1.267 0.399,0.143 10 3.0 V 1.446,2.104 1.794,2.254 0.348,0.15 10 1.0 V 1.446,2.774 1.736,2.923 0.29,0.149 10 0 V 2.64,3.111 3.396,3.258 0.756,0.147 10 10 seconds 5.042,3.08 5.797,3.221 0.755,0.141 10 10 seconds

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0420)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine and ECT > Trouble Codes
50001 234

d.

Read DTCs.

Result:
Result Proceed to
DTC P0420 is output A
DTC P0420 and other DTCs are output B


HINT:

If any DTCs other than P0420 are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (INJECTION VOLUME CONTROL)

B

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (INJECTION VOLUME CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine and turn the tester on.


c.

Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F sensor.

Powertrain > Engine and ECT > Active Test
Active Test Display
Control the Injection Volume for A/F Sensor
Data List Display
AFS Voltage B1S1
O2S B1S2
50004 234 2 35,44

e.

Perform the Control the Injection Volume for A/F sensor operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).


f.

Monitor the voltage outputs of the air fuel ratio and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2) displayed on the tester.

HINT:
·

The Control the Injection Volume for A/F sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

Each sensor reacts in accordance with increases and decreases in the fuel injection volume.



Standard:
Tester Display
(Sensor)
Injection Volume Status Voltage
AFS Voltage B1S1
(Air fuel ratio sensor)
+12.5% Rich Below 3.1 V
AFS Voltage B1S1
(Air fuel ratio sensor)
-12.5% Lean Higher than 3.4 V
O2S B1S2
(Heated oxygen sensor)
+12.5% Rich Higher than 0.55 V
O2S B1S2
(Heated oxygen sensor)
-12.5% Lean Below 0.4 V


Result:
Status of AFS Voltage B1S1 Status of O2S B1S2 A/F Condition and A/F and HO2 Sensor Condition Misfire Main Suspected Trouble Area Proceed to

Lean: During Control the Injection Volume for A/F sensor, the air fuel ratio sensor output voltage (AFS) is consistently higher than 3.4 V, and the heated oxygen sensor output voltage (O2S) is consistently below 0.4 V.

Rich: During Control the Injection Volume for A/F sensor, the AFS voltage is consistently below 3.1 V, and the O2S voltage is consistently higher than 0.55 V.

Lean/Rich: During Control the Injection Volume for A/F sensor of the Active Test, the output voltages of the air fuel ratio sensor and heated oxygen sensor alternate correctly.

Lean/Rich Lean/Rich Normal -
·

Three Way Catalytic Converter (TWC)

·

Gas leak from exhaust system


A
Lean Lean/Rich Air fuel ratio sensor malfunction - Air fuel ratio sensor B
Rich Lean/Rich Air fuel ratio sensor malfunction - Air fuel ratio sensor
Lean/Rich Lean Heated oxygen sensor malfunction -
·

Heated oxygen sensor

·

Gas leak from exhaust system


C
Lean/Rich Rich Heated oxygen sensor malfunction -
·

Heated oxygen sensor

·

Gas leak from exhaust system


Lean Lean Actual air fuel ratio lean May occur
·

Extremely rich or lean actual air fuel ratio

·

Gas leak from exhaust system


D
Rich Rich Actual air fuel ratio rich -
·

Extremely rich or lean actual air fuel ratio

·

Gas leak from exhaust system






A

3.INSPECT FOR EXHAUST GAS LEAK

B

C

6.INSPECT FOR EXHAUST GAS LEAK

D

CHECK EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO, REPAIR CAUSE AND GO TO STEP 3

3.INSPECT FOR EXHAUST GAS LEAK
a.

Inspect for exhaust gas leakage.

OK:

No gas leakage.



Result:
Proceed to
OK
NG



OK

4.REPLACE FRONT EXHAUST PIPE ASSEMBLY (TWC: FRONT CATALYST AND REAR CATALYST)

NG

REPAIR OR REPLACE EXHAUST GAS LEAK POINT

4.REPLACE FRONT EXHAUST PIPE ASSEMBLY (TWC: FRONT CATALYST AND REAR CATALYST)
a.

Replace the front exhaust pipe assembly.

Click hereEngine / Hybrid System>2TR-FBE INTAKE / EXHAUST>EXHAUST PIPE>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS
5.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

d.

Drive the vehicle at a speed between 64 km/h and 113 km/h (40 mph and 70 mph) for at least 10 minutes.


e.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine and ECT > Trouble Codes
50001 234

f.

Read the DTCs (Pending DTCs).

Result:

Pending DTC is not output



Result:
Proceed to
NEXT



NEXT

END

6.INSPECT FOR EXHAUST GAS LEAK
a.

Inspect for exhaust gas leakage.

OK:

No gas leakage.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE EXHAUST GAS LEAK POINT