Home › Engine / Hybrid System › 2TR-FE ENGINE CONTROL › SFI SYSTEM(w/ Secondary Air Injection System) › from 2012.10
RM1840EF _51 Engine / Hybrid System _009569 2TR-FE ENGINE CONTROL _0052076 SFI SYSTEM(w/ Secondary Air Injection System) C

2TR-FE ENGINE CONTROL  SFI SYSTEM(w/ Secondary Air Injection System)  P0420  Catalyst System Efficiency Below Threshold (Bank 1)  


MONITOR DESCRIPTION

The ECM uses sensors mounted in front of and behind the Three-way Catalytic Converter (TWC) to monitor its efficiency.

The first sensor, the air fuel ratio sensor, sends pre-catalyst information to the ECM. The second sensor, the heated oxygen sensor, sends post-catalyst information to the ECM.

In order to detect any deterioration in the Three-way Catalytic Converter (TWC), the ECM calculates the Oxygen Storage Capacity (OSC) of the Three-way Catalytic Converter (TWC). This calculation is based on the voltage output of the heated oxygen sensor while performing active air-fuel ratio control.

The OSC value is an indication of the oxygen storage capacity of the Three-way Catalytic Converter (TWC). When the vehicle is being driven with a warm engine, active air-fuel ratio control is performed for approximately 15 to 20 seconds. When it is performed, the ECM deliberately sets the air-fuel ratio to lean or rich levels. If the rich-lean cycle of the heated oxygen sensor is long, the OSC becomes greater. There is a direct correlation between the OSCs of the heated oxygen sensor and Three-way Catalytic Converter (TWC).

The ECM uses the OSC value to determine the state of the Three-way Catalytic Converter (TWC). If any deterioration has occurred, it illuminates the MIL and stores the DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0420 Catalyst System Efficiency Below Threshold (Bank 1) OSC value is less than the standard value under active air-fuel ratio control (2 trip detection logic).
·

Gas leak from exhaust system

·

Air fuel ratio sensor (for Bank 1 Sensor 1)

·

Heated oxygen sensor (for Bank 1 Sensor 2)

·

Front exhaust pipe assembly (TWC: Front catalyst and rear catalyst)


Comes on DTC stored

CATALYST LOCATION

A242742
0.427,1.823 0.615,1.042 0.615,1.042 0.823,1.042 false 0.948,1.771 1.125,1.5 1.125,1.5 1.271,1.5 false 2.146,2.323 2.438,2.573 false 2.438,2.573 2.76,2.573 false 2.635,2.094 3.063,1.104 3.063,1.104 3.229,1.104 false 4.646,1.854 5.146,2.281 5.146,2.281 5.479,2.281 false 5.646,0.854 5.292,0.531 5.292,0.531 4.979,0.531 false 1.302,2.49 1.156,2.833 1.156,2.833 0.99,2.833 false 2.094,2.865 2.24,3.385 2.24,3.385 2.417,3.385 false 0.875,0.938 1.125,1.115 0.25,0.177 10 false *1 1.302,1.417 1.552,1.594 0.25,0.177 10 false *2 0.813,2.75 1.063,2.927 0.25,0.177 10 false *3 3.292,1.031 3.542,1.208 0.25,0.177 10 false *5 2.813,2.51 3.063,2.688 0.25,0.177 10 false *4 2.479,3.323 2.729,3.5 0.25,0.177 10 false *6 5.531,2.177 5.781,2.354 0.25,0.177 10 false *7 4.771,0.448 5.021,0.625 0.25,0.177 10 false *8
*1 Exhaust Manifold *2 Air Fuel Ratio Sensor
*3 TWC: Front Catalyst *4 TWC: Rear Catalyst
*5 Front Exhaust Pipe Assembly *6 Heated Oxygen Sensor
*7 Center Exhaust Pipe Assembly *8 Tailpipe Assembly


MONITOR STRATEGY

Required Sensors/Components (Main) Air fuel ratio sensor, heated oxygen sensor
Required Sensors/Components (Related) Intake air temperature sensor, mass air flow meter, crankshaft position sensor and engine coolant temperature sensor
Frequency of Operation Once per driving cycle

TYPICAL ENABLING CONDITIONS

Battery voltage 11 V or higher
Intake air temperature -10°C (14°F) or higher
Engine coolant temperature 75°C (167°F) or higher
Atmospheric pressure 76 kPa (570 mmHg) or higher
Idling OFF
Engine speed Less than 4000 rpm
Air fuel ratio sensor status Activated
Fuel system status Closed loop
Engine load 10 to 80%
All of following conditions (a), (b) and (c) met -
(a) Mass air flow 2.5 to 33 gm/s
(b) Estimated front catalyst temperature 685 to 800°C (1265 to 1472°F)
(c) Estimated rear catalyst temperature 400 to 800°C (752 to 1472°F)
Transmission gear 4th or higher

CONFIRMATION DRIVING PATTERN

HINT:

Performing this confirmation driving pattern will activate the catalyst efficiency monitor. This is very useful for verifying the completion of a repair.


A283969
1.927,0.313 1.719,0.313 1.719,0.313 1.313,0.76 false 0.74,1.146 1.26,1.396 0.521,0.25 10 false 37 mph 0.833,2.229 1.229,2.5 0.396,0.271 10 false Idling 0.146,2.417 1.281,2.656 1.135,0.24 10 false Ignition Switch off 1.479,2.74 2.063,3.177 0.583,0.438 10 false Warming up 2.365,2.729 3.083,3.25 0.719,0.521 10 false 10 minutes or more 4.135,2.74 4.854,3.135 0.719,0.396 10 false 10 minutes or more 1.969,0.25 3.625,0.542 1.656,0.292 10 false Between 47 and 63 mph 1.667,2.094 1.906,2.333 0.24,0.24 10 false [A] 2.604,1 2.927,1.292 0.323,0.292 10 false [B]* 3.156,3.125 3.396,3.333 0.24,0.208 10 false [C] 6.771,3.115 7.063,3.365 0.292,0.25 10 false [H] 4.271,2.083 4.594,2.469 0.323,0.385 10 false [C] 3.469,2.063 3.688,2.385 0.219,0.323 10 false [D] 6.188,0.635 6.583,0.896 0.396,0.26 10 false [G]* 4.375,1 4.729,1.198 0.354,0.198 10 false [E]* 5,3.146 5.24,3.427 0.24,0.281 10 false [F] 3.365,2.74 3.969,3.125 0.604,0.385 10 false Warming up 5.885,2.74 6.635,3.135 0.75,0.396 10 false 10 minutes or more 0.24,3.396 5.292,3.698 5.052,0.302 10 false *: Drive the vehicle while keeping the engine load as constant as possible

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the intelligent tester on.

4.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON and turn the intelligent tester on.

7.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [A].

8.

Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Drive the vehicle while keeping the engine load as constant as possible.


9.

Turn the ignition switch off and wait for at least 30 seconds [C].

10.

Turn the ignition switch to ON and turn the intelligent tester on.

11.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [D].

12.

Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [E].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Drive the vehicle while keeping the engine load as constant as possible.


13.

Enter the following menus: Powertrain / Engine and ETC / DTC [F].

14.

Check if any DTCs (pending DTCs) are stored.

15.

Drive the vehicle at a speed between 75 and 100 km/h (47 and 63 mph) for 10 minutes or more [G].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Drive the vehicle while keeping the engine load as constant as possible.


16.

Enter the following menus: Powertrain / Engine and ETC / DTC [H].

17.

Check if any DTCs (pending DTCs) are stored.


CONDITIONING FOR SENSOR TESTING

HINT:

Perform the operation with the engine speeds and time durations described below prior to checking the waveforms of the air fuel ratio and heated oxygen sensors. This is to activate the sensors sufficiently to obtain appropriate inspection results.


A118003
4.906,3.073 4.906,3.292 false 4.906,3.292 5.26,3.292 false 5.198,3.073 5.198,3.292 false 3.625,0.896 3.885,1.125 0.26,0.229 10 (c) 0.573,0.646 1.583,0.865 1.01,0.219 10 Engine Speed 0.844,1.01 1.615,1.208 0.771,0.198 10 3000 rpm 0.844,1.583 1.594,1.781 0.75,0.198 10 2000 rpm 1.115,2.51 1.583,2.802 0.469,0.292 10 Idling 0.354,2.74 1.521,3 1.167,0.26 10 Ignition Switch off 1.656,2.646 1.917,2.885 0.26,0.24 10 (a) 2.073,2.438 2.354,2.688 0.281,0.25 10 (b) 4.792,0.896 5.063,1.146 0.271,0.25 10 (d) 5.094,1.458 5.406,1.74 0.313,0.281 10 (d) 2.094,3.104 3.01,3.302 0.917,0.198 10 Warming up 3.365,3.104 4.542,3.302 1.177,0.198 10 At least 3 minutes 5.302,3.219 6.115,3.417 0.813,0.198 10 2 seconds 4.865,3.323 5.333,3.542 0.469,0.219 10 Check 6.635,2.76 7.021,3.042 0.385,0.281 10 Time

(a) Connect the intelligent tester to the DLC3.

(b) Start the engine and warm it up with all the accessories switched off until the engine coolant temperature stabilizes.

(c) Run the engine at an engine speed of between 2500 rpm and 3000 rpm for at least 3 minutes.

(d) While running the engine at 3000 rpm for 2 seconds, and then 2000 rpm for 2 seconds, check the waveforms of the air fuel ratio and heated oxygen sensors using the intelligent tester.


HINT:
·

If the voltage output of either the air fuel ratio or heated oxygen sensor does not fluctuate, or there is noise in the waveform of either sensor, the sensor may be malfunctioning.

·

If the voltage outputs of both the sensors remain lean or rich, the air-fuel ratio may be extremely lean or rich. In such cases, perform the Control the Injection Volume for A/F Sensor Active Test using the intelligent tester.

·

If the Three-way Catalytic Converter (TWC) has deteriorated, the heated oxygen sensor (located behind the Three-way Catalytic Converter (TWC)) voltage output fluctuates up and down frequently, even under normal driving conditions (active air-fuel ratio control is not performed).



Result of Real-vehicle Check
Engine Speed 3000 rpm (without load) 2000 rpm (during fuel-cut) 2000 rpm (revving up the engine)
AFS Voltage B1S1 3.263 to 3.302 V 4.996 V 3.195 V
O2S B1S2 0.820 to 0.835 V 0.015 V 0.820 V

A121610
0.073,0.073 4.417,0.354 4.344,0.281 10 false Voltage output when active air-fuel ratio control not performed: 2.375,0.417 3.667,0.667 1.292,0.25 10 false Normal Catalyst 4.74,0.427 6.167,0.667 1.427,0.24 10 false Deteriorated Catalyst 0.063,2.042 1.323,2.885 1.26,0.844 10 false Waveform of Heated Oxygen Sensor behind Three-way Catalytic Converter 0.083,0.531 1.375,1.354 1.292,0.823 10 false Waveform of Air Fuel Ratio Sensor in front of Three-way Catalytic Converter 1.49,0.781 2.146,1.125 0.656,0.344 10 false 3.5 V 1.49,1.125 2.01,1.354 0.521,0.229 10 false 3.0 V 1.49,2.073 1.938,2.26 0.448,0.188 10 false 1.0 V 1.49,2.76 1.885,2.948 0.396,0.188 10 false 0 V 2.635,3.115 3.5,3.365 0.865,0.25 10 false 10 seconds 5.042,3.115 5.948,3.354 0.906,0.24 10 false 10 seconds

CAUTION / NOTICE / HINT

HINT:
·

If a malfunction cannot be found when troubleshooting DTC P0420, a lean or rich abnormality may be the cause. Perform troubleshooting by following the inspection procedure for P0171 (System Too Lean) and P0172 (System Too Rich).

·

After performing repairs, drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern and check if DTC P0420 is output again. If a DTC is output again, replace the catalyst if it has not been replaced already.

·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.



PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0420)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

e.

Read the DTCs.

Result:
Result Proceed to
P0420 is output A
P0420 and other DTCs are output B


HINT:

If any DTCs other than P0420 are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME)

B

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the intelligent tester on.


d.

Warm up the engine and run the engine at an engine speed of 2500 rpm for approximately 90 seconds.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.

Powertrain > Engine > Active Test
Tester Display
Control the Injection Volume for A/F Sensor
50004 61 2

f.

Perform the Control the Injection Volume for A/F Sensor operation with the engine idling.


g.

Monitor the voltage outputs of the air fuel ratio and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2) displayed on the intelligent tester.

HINT:
·

Change the fuel injection volume within the range of -12.5% to +12.5%.

·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



Intelligent Tester Display
(Sensor)
Injection Volume Status Voltage
AFS Voltage B1S1
(Air fuel ratio)
+12.5% Rich Below 3.1 V
AFS Voltage B1S1
(Air fuel ratio)
-12.5% Lean Higher than 3.4 V
O2S B1S2
(Heated oxygen)
+12.5% Rich Higher than 0.55 V
O2S B1S2
(Heated oxygen)
-12.5% Lean Below 0.4 V

Result:
Status of AFS Voltage B1S1 Status of O2S B1S2 Air Fuel Ratio Condition and Air Fuel Ratio and Heated Oxygen Sensor Condition Suspected Trouble Area Proceed to

Lean: During the Control the Injection Volume for A/F Sensor Active Test, the air fuel ratio sensor output voltage (AFS Voltage) is consistently higher than 3.4 V, and the heated oxygen sensor output voltage (O2S) is consistently below 0.4 V.

Rich: During the Control the Injection Volume for A/F Sensor Active Test, the air fuel ratio sensor output voltage (AFS Voltage) is consistently below 3.1 V, and the heated oxygen sensor voltage (O2S) is consistently higher than 0.55 V.

Lean/Rich: During the Control the Injection Volume for A/F Sensor Active Test, the output voltage of the air fuel ratio sensor and heated oxygen sensor alternate correctly.

Lean/Rich Lean/Rich Normal
·

Three-way catalytic converter

·

Gas leaks from exhaust system


A
Lean Lean/Rich Air fuel ratio sensor malfunction Air fuel ratio sensor B
Rich Lean/Rich Air fuel ratio sensor malfunction Air fuel ratio sensor
Lean/Rich Lean Heated oxygen sensor malfunction
·

Heated oxygen sensor

·

Gas leaks from exhaust system


C
Lean/Rich Rich Heated oxygen sensor malfunction
·

Heated oxygen sensor

·

Gas leaks from exhaust system


Lean Lean Actual air fuel ratio lean
·

Extremely rich or lean actual air fuel ratio

·

Gas leaks from exhaust system


D
Rich Rich Actual air fuel ratio lean
·

Extremely rich or lean actual air fuel ratio

·

Gas leaks from exhaust system




HINT:

Refer to "Data List / Active Test" [AFS Voltage B1S1 and O2S B1S2].

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM(w/ Secondary Air Injection System)>DATA LIST / ACTIVE TEST




A

3.CHECK FOR EXHAUST GAS LEAK

B

5.REPLACE AIR FUEL RATIO SENSOR

C

6.CHECK FOR EXHAUST GAS LEAK

D

8.CHECK FOR EXHAUST GAS LEAK
3.CHECK FOR EXHAUST GAS LEAK
a.

Inspect for exhaust gas leaks from the exhaust manifold and exhaust pipes.

OK:

No gas leaks.



Result:
Proceed to
OK
NG



OK

4.REPLACE FRONT EXHAUST PIPE ASSEMBLY (TWC: FRONT CATALYST AND REAR CATALYST)

NG

REPAIR OR REPLACE EXHAUST GAS LEAK POINT

4.REPLACE FRONT EXHAUST PIPE ASSEMBLY (TWC: FRONT CATALYST AND REAR CATALYST)
NOTICE:

Replace the front and rear catalyst together when catalyst replacement is necessary.


HINT:

Refer to the illustration in Catalyst Location to confirm which parts to replace.


a.

Replace the front exhaust pipe assembly.

Click hereEngine / Hybrid System>2TR-FE INTAKE / EXHAUST>EXHAUST PIPE>REMOVAL


Result:
Proceed to
NEXT



NEXT

END

5.REPLACE AIR FUEL RATIO SENSOR

Result:
Proceed to
NEXT



NEXT

10.CHECK WHETHER DTC OUTPUT RECURS (DTC P0420)
6.CHECK FOR EXHAUST GAS LEAK
a.

Inspect for exhaust gas leaks from the exhaust manifold and exhaust pipes.

OK:

No gas leaks.



Result:
Proceed to
OK
NG



OK

7.REPLACE HEATED OXYGEN SENSOR

NG

REPAIR OR REPLACE EXHAUST GAS LEAK POINT

7.REPLACE HEATED OXYGEN SENSOR

Result:
Proceed to
NEXT



NEXT

10.CHECK WHETHER DTC OUTPUT RECURS (DTC P0420)
8.CHECK FOR EXHAUST GAS LEAK
a.

Inspect for exhaust gas leaks from the exhaust manifold and exhaust pipes.

OK:

No gas leaks.



Result:
Proceed to
OK
NG



OK

9.CHECK CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO

NG

REPAIR OR REPLACE EXHAUST GAS LEAK POINT

9.CHECK CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO
a.

Check the cause of the extremely rich or lean actual air fuel ratio while referring to the DTC P0171 Procedure.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM(w/ Secondary Air Injection System)>P0171


Result:
Proceed to
NEXT



NEXT

10.CHECK WHETHER DTC OUTPUT RECURS (DTC P0420)
10.CHECK WHETHER DTC OUTPUT RECURS (DTC P0420)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the intelligent tester on.


h.

Start the engine.


i.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


j.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

k.

Read the DTCs.

Result:
Result Proceed to
P0420 is output A
No DTC is output B


HINT:

If any DTCs other than P0420 are output, troubleshoot those DTCs first.




A

11.REPLACE FRONT EXHAUST PIPE ASSEMBLY (TWC: FRONT CATALYST AND REAR CATALYST)

B

END

11.REPLACE FRONT EXHAUST PIPE ASSEMBLY (TWC: FRONT CATALYST AND REAR CATALYST)
NOTICE:

Replace the front and rear catalyst together when catalyst replacement is necessary.


HINT:

Refer to the illustration in Catalyst Location to confirm which parts to replace.


a.

Replace the front exhaust pipe assembly.

Click hereEngine / Hybrid System>2TR-FE INTAKE / EXHAUST>EXHAUST PIPE>REMOVAL


Result:
Proceed to
NEXT



NEXT

END