Home › Engine / Hybrid System › 2TR-FBE ENGINE CONTROL › SFI SYSTEM › from 2012.10
RM1840EF _51 Engine / Hybrid System _009571 2TR-FBE ENGINE CONTROL _0052126 SFI SYSTEM C

2TR-FBE ENGINE CONTROL  SFI SYSTEM  P0724  Brake Switch "B" Circuit High  


DESCRIPTION

The purpose of this circuit is to prevent the engine from stalling while driving in the lock-up condition when the brakes are suddenly applied.

When the brake pedal is depressed, the stop light switch sends a signal to the ECM. Then the ECM cancels the operation of the lock-up clutch while braking is in progress.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0724 Brake Switch "B" Circuit High The stop light switch remains on even when the vehicle is driven in a GO (30 km/h (18.63 mph) or more) and STOP (less than 3 km/h (1.86 mph)) pattern 5 times (2 trip detection logic).
·

Stop light switch assembly signal circuit

·

Stop light switch assembly

·

ECM


Comes on DTC stored

WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:
·

Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Stop Light Switch.

Powertrain > Engine and ECT > Data List
Tester Display
Stop Light Switch
50003 234 117

e.

Read the value displayed on the tester when the brake pedal is depressed and released.

OK:
Brake Pedal Display
Released OFF
Depressed ON



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT STOP LIGHT SWITCH ASSEMBLY
2.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.
A072924
2.365,0.677 2.615,1.094 false 3.167,0.646 2.865,1.083 false 3.188,1.781 2.917,1.333 false 2.281,1.792 2.563,1.333 false 0.063,0.052 0.906,0.323 0.844,0.271 10 false Not Pushed 1.177,0.635 2.021,0.906 0.844,0.271 10 false Pushed 2.271,0.5 2.438,0.719 0.167,0.219 10 false 2 3.177,0.5 3.344,0.719 0.167,0.219 10 false 1 2.198,1.792 2.365,2.01 0.167,0.219 10 false 4 3.188,1.802 3.354,2.021 0.167,0.219 10 false 3

Inspect the stop light switch assembly.

i.

Measure the voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - 2 Pin not pushed Below 1 Ω
3 - 4 Pin not pushed 10 kΩ or higher
1 - 2 Pin pushed 10 kΩ or higher
3 - 4 Pin pushed Below 1 Ω




Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (ECM - STOP LIGHT SWITCH ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (ECM - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the ECM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G146-18 (STP) - Body ground Brake pedal depressed 11 to 14 V
G146-18 (STP) - Body ground Brake pedal released Below 1.5 V



c.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - STOP LIGHT SWITCH ASSEMBLY)