A Flexible Fuel Vehicle (FFV) is a vehicle with an engine that can be used with a high concentration of ethyl alcohol fuel.
This FFV uses a sub tank system, which allows fuel (with a gasoline concentration of 78% or more) to be injected to the fuel delivery spacer from the sub tank when the ambient temperature is low to enhance low-temperature startability.
The fuel volume is controlled by the ECM and varies depending on the duty ratio of the fuel injection volume control solenoid valve assembly.
If the fuel injection volume control solenoid valve assembly is stuck open, the fuel cut solenoid valve assembly will operate and cut the fuel flow based on signals from the ECM, preventing the fuel from being drawn out of the sub tank due to vacuum from the engine.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P1001 | Fuel Sub Tank Solenoid Duty Control Circuit | Both conditions are met (1 trip detection logic): 1.
Target duty ratio of fuel injection volume control solenoid valve is between 5 and 90%. 2.
Difference between target control value and actual control value continues for 2 seconds or more. |
·
Open or short in solenoid valve assembly (for fuel injection volume control) circuit ·
Solenoid valve assembly (for fuel injection volume control) ·
FFV relay ·
ECM |
Does not come on | DTC stored |
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Remove the FFV relay from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 - 5 | Battery voltage is not applied between terminals 1 and 2 | 10 kΩ or higher |
| 3 - 5 | Battery voltage is applied between terminals 1 and 2 | Below 1 Ω |
Reinstall the FFV relay.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the FFV relay from the engine room relay block.
Disconnect the solenoid valve assembly (for fuel injection volume control) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| FFV relay terminal (3) - A70-2 (FFV+) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| FFV relay terminal (3) or A70-2 (FFV+) - Body ground | Always | 10 kΩ or higher |
Reinstall the FFV relay.
Reconnect the solenoid valve assembly (for fuel injection volume control) connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the solenoid valve assembly (for fuel injection volume control).
Click hereEngine / Hybrid System>2TR-FBE FUEL>SOLENOID VALVE(for Fuel Injection Volume Control)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>2TR-FBE FUEL>SOLENOID VALVE(for Fuel Injection Volume Control)>REMOVAL
Disconnect the solenoid valve assembly (for injection volume control) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A70-1 (FFV-) - G145-18 (DSSV) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A70-1 (FFV-) or G145-18 (DSSV) - Body ground | Always | 10 kΩ or higher |
Reconnect the solenoid valve assembly (for injection volume control) connector.
Reconnect the ECM connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the sub tank fuel pump control circuit.
Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>Sub Tank Fuel Pump Control Circuit
| Proceed to |
|---|
| OK |
| NG |
OK
NG