Home › Engine / Hybrid System › 2TR-FBE ENGINE CONTROL › SFI SYSTEM › from 2012.10
RM1840EF _51 Engine / Hybrid System _009571 2TR-FBE ENGINE CONTROL _0052126 SFI SYSTEM C

2TR-FBE ENGINE CONTROL  SFI SYSTEM  P100B  Open in Sub Fuel Tank VSV Control Circuit  P100C  Short in Sub Fuel Tank VSV Control Circuit  


DESCRIPTION

A Flexible Fuel Vehicle (FFV) is a vehicle with an engine that can be used with a high concentration of ethyl alcohol fuel.

This FFV uses a sub tank system, which allows fuel (with a gasoline concentration of 78% or more) to be injected to the fuel delivery spacer from the sub tank when the ambient temperature is low to enhance low-temperature startability.

The fuel volume is controlled by the ECM and varies depending on the duty ratio of the fuel injection volume control solenoid valve.

If the fuel injection volume control solenoid valve is stuck open, the fuel cut solenoid valve will operate and cut the fuel flow based on signals from the ECM, preventing the fuel from being drawn out of the sub tank due to vacuum from the engine.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P100B Open in Sub Fuel Tank VSV Control Circuit

All conditions are met (1 trip detection logic):

1.

FFR signal is on.

2.

SSV signal is off.

3.

Low voltage at terminal SSV continues for 1 second or more.



·

Open in solenoid valve assembly (for fuel cut control) circuit

·

Solenoid valve assembly (for fuel cut control)

·

FFV relay

·

ECM


Does not come on DTC stored
P100C Short in Sub Fuel Tank VSV Control Circuit

All conditions are met (1 trip detection logic):

1.

FFR signal is off.

2.

SSV signal is off.

3.

High voltage at terminal SSV continues for 10 seconds or more.



·

Short in solenoid valve assembly (for fuel cut control) circuit

·

Solenoid valve assembly (for fuel cut control)

·

FFV relay

·

ECM


Does not come on DTC stored

WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT FFV RELAY
a.
A234567
2.354,1.552 2.354,1.313 false 2.771,1.563 2.615,1.219 false 2.344,0.677 2.344,0.917 false 2.781,0.667 2.875,1.01 false 2.313,0.5 2.469,0.698 0.156,0.198 10 false 2 2.75,0.49 2.906,0.688 0.156,0.198 10 false 3 2.313,1.573 2.469,1.771 0.156,0.198 10 false 1 2.76,1.573 2.917,1.771 0.156,0.198 10 false 5

Remove the FFV relay from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage is not applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Battery voltage is applied between terminals 1 and 2 Below 1 Ω



c.

Reinstall the FFV relay.


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (FFV RELAY - SOLENOID VALVE ASSEMBLY (FOR FUEL CUT CONTROL))

NG

REPLACE FFV RELAY

2.CHECK HARNESS AND CONNECTOR (FFV RELAY - SOLENOID VALVE ASSEMBLY (FOR FUEL CUT CONTROL))
a.

Remove the FFV relay from the engine room relay block.


b.

Disconnect the solenoid valve assembly (for fuel cut control) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
FFV relay terminal (3) - A69-2 (SFC+) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
FFV relay terminal (3) or A69-2 (SFC+) - Body ground Always 10 kΩ or higher



d.

Reinstall the FFV relay.


e.

Reconnect the solenoid valve assembly (for fuel cut control) connector.


Result:
Proceed to
OK
NG



OK

3.INSPECT SOLENOID VALVE ASSEMBLY (FOR FUEL CUT CONTROL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (FFV RELAY - SOLENOID VALVE (FOR FUEL CUT CONTROL))

3.INSPECT SOLENOID VALVE ASSEMBLY (FOR FUEL CUT CONTROL)
a.

Inspect the solenoid valve assembly (for fuel cut control).

Click hereEngine / Hybrid System>2TR-FBE FUEL>SOLENOID VALVE(for Fuel Cut Control)>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (SOLENOID VALVE ASSEMBLY (FOR FUEL CUT CONTROL) - ECM)

NG

REPLACE SOLENOID VALVE ASSEMBLY (FOR FUEL CUT CONTROL)

4.CHECK HARNESS AND CONNECTOR (SOLENOID VALVE ASSEMBLY (FOR FUEL CUT CONTROL) - ECM)
a.

Disconnect the solenoid valve assembly (for fuel cut control) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A69-1 (SFC-) - G145-1 (SSV) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A69-1 (SFC-) or G145-1 (SSV) - Body ground Always 10 kΩ or higher



d.

Reconnect the solenoid valve assembly (for fuel cut control) connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

5.CHECK SUB TANK FUEL PUMP CONTROL CIRCUIT

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (SOLENOID VALVE ASSEMBLY (FOR FUEL CUT CONTROL) - ECM)

5.CHECK SUB TANK FUEL PUMP CONTROL CIRCUIT
a.

Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE SUB TANK FUEL PUMP CONTROL CIRCUIT