Home › Engine / Hybrid System › 2TR-FE ENGINE CONTROL › SFI SYSTEM(w/ Secondary Air Injection System) › from 2012.10
RM1840EF _51 Engine / Hybrid System _009569 2TR-FE ENGINE CONTROL _0052076 SFI SYSTEM(w/ Secondary Air Injection System) C

2TR-FE ENGINE CONTROL  SFI SYSTEM(w/ Secondary Air Injection System)  P0724  Brake Switch "B" Circuit High  


DESCRIPTION

The stop light switch is part of a duplex system that transmits 2 signals: STP and ST1-. These 2 signals are used by the ECM to monitor whether or not the brake system is working properly. This DTC indicates that the stop light switch remains on. When the stop light switch remains on during GO and STOP driving, the ECM interprets this as a fault in the stop light switch. Then the MIL illuminates and the ECM stores the DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0724 Brake Switch "B" Circuit High Stop light switch remains on even when the vehicle is driven in a GO (30 km/h (18.63 mph) or more) and STOP (less than 3 km/h (1.86 mph)) pattern 5 times (2 trip detection logic).
·

Short in stop light switch signal circuit

·

Stop light switch assembly

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

This DTC indicates that the stop light switch remains on. When the stop light switch remains on during GO and STOP driving, the ECM interprets this as a fault in the stop light switch. Then the MIL illuminates and the ECM stores the DTC. The vehicle must GO (30 km/h (18.63 mph) or more) and STOP (less than 3 km/h (1.86 mph)) 5 times for 2 driving cycles in order for the DTC to be stored.

MONITOR STRATEGY

Required sensors/Components Stop light switch assembly, Vehicle speed sensor
Frequency of operation Continuous

CONFIRMATION DRIVING PATTERN

A199312
1.417,2.052 1.792,2.281 0.375,0.229 10 false Idling 0.615,2.385 1.885,2.708 1.271,0.323 10 false Ignition Switch ON 2.521,2.479 2.771,2.719 0.25,0.24 10 false [A] 2.583,3.083 3.292,3.323 0.708,0.24 10 false 5 seconds 3.271,3.49 3.573,3.729 0.302,0.24 10 false [B] 3.406,1.917 3.688,2.146 0.281,0.229 10 false [C] 6.729,3.479 7,3.729 0.271,0.25 10 false [E] 4.031,1.5 4.344,1.771 0.313,0.271 10 false [D] 0.479,1.219 1.833,1.5 1.354,0.281 10 false 30 km/h (18.65 mph) 0.635,1.75 1.896,1.979 1.26,0.229 10 false 3 km/h (1.86 mph)

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the intelligent tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the intelligent tester on [A].

6.

Wait 5 seconds.

7.

Enter the following menus: Powertrain / Engine and ECT / DTC [B].

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P0724.

11.

Check the DTC judgment result.

Intelligent Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [C] through [E].



12.

Start the engine [C].

13.

Accelerate the vehicle to 30 km/h (19 mph) or more, and then depress the brake pedal and decelerate the vehicle to 3 km/h (1.8 mph) or less [D]. Repeat step [D] 5 times.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


14.

Check the DTC judgment result [E].


CAUTION / NOTICE / HINT

HINT:

Using the intelligent tester, the Data List item "Stop Light Switch" can be read.


Item Measurement Item/
Range
Normal Condition Diagnostic Note
Stop Light Switch Stop light switch status/
ON or OFF
·

Brake pedal depressed: ON

·

Brake pedal released: OFF


-

PROCEDURE

1.CHECK STOP LIGHT SWITCH ASSEMBLY INSTALLATION
a.

Check the stop light switch assembly installation.

OK:

Stop light switch assembly is installed correctly.



Result:
Proceed to
OK
NG



OK

2.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

SECURELY REINSTALL STOP LIGHT SWITCH ASSEMBLY

2.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (ECM - BATTERY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (ECM - BATTERY)
a.
A253285
1.833,1.469 2.25,1.729 0.417,0.26 1.802,2.948 2.01,2.115 true 1.729,2.99 2.24,3.167 0.51,0.177 10 false 4 (STP) 0.073,0.021 0.281,0.198 0.208,0.177 10 false *a 1.906,1.521 2.208,1.677 0.302,0.156 10 false G88
*a Rear view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G88-4 (STP) - Body ground Brake pedal is depressed 11 to 14 V
Brake pedal is depressed Below 1 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR