Home › Engine / Hybrid System › 2TR-FBE ENGINE CONTROL › SFI SYSTEM › from 2012.10
RM1840EF _51 Engine / Hybrid System _009571 2TR-FBE ENGINE CONTROL _0052126 SFI SYSTEM C

2TR-FBE ENGINE CONTROL  SFI SYSTEM  P2237  Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 1 Sensor 1)  P2238  Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 1 Sensor 1)  P2239  Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 1 Sensor 1)  P2252  Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 1 Sensor 1)  P2253  Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 1 Sensor 1)  


DESCRIPTION

Refer to DTC P2195 (See page Engine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>P2195).

HINT:
·

Although the DTC titles refer to the oxygen sensor, these DTCs relate to the air fuel ratio sensor.

·

Sensor 1 refers to the sensor mounted in front of the three way catalytic converter and located near the engine assembly.



DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2237 Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 1 Sensor 1) An open in the circuit between terminals A1A+ and A1A- of the air fuel ratio sensor while the engine is running (2 trip detection logic).
·

Open or short in air fuel ratio sensor circuit

·

Air fuel ratio sensor

·

ECM


Comes on DTC stored
P2238 Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 1 Sensor 1) One of the following conditions is met (2 trip detection logic):
·

The air fuel ratio sensor output drops while the engine is running.

·

The voltage at terminal A1A+ is 0.5 V or less.

·

The voltage difference between terminals A1A+ and A1A- is 0.1 V or less.


·

Open or short in air fuel ratio sensor circuit

·

Air fuel ratio sensor

·

ECM


Comes on DTC stored
P2239 Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 1 Sensor 1) The A1A+ voltage is higher than 4.5 V (2 trip detection logic).
·

Open or short in air fuel ratio sensor circuit

·

Air fuel ratio sensor

·

ECM


Comes on DTC stored
P2252 Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 1 Sensor 1) The A1A- voltage is 0.5 V or less (2 trip detection logic).
·

Open or short in air fuel ratio sensor circuit

·

Air fuel ratio sensor

·

ECM


Comes on DTC stored
P2253 Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 1 Sensor 1) A1A- voltage is higher than 4.5 V (2 trip detection logic).
·

Open or short in air fuel ratio sensor circuit

·

Air fuel ratio sensor

·

ECM


Comes on DTC stored

WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
a.

Disconnect the air fuel ratio sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C85-3 (A1A+) - C97-7 (A1A+) Always Below 1 Ω
C85-4 (A1A-) - C97-1 (A1A-) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C85-3 (A1A+) or C97-7 (A1A+) - Body ground Always 10 kΩ or higher
C85-4 (A1A-) or C97-1 (A1A-) - Body ground Always 10 kΩ or higher



d.

Reconnect the ECM connector.


e.

Reconnect the air fuel ratio sensor connector.

A227661
0.115,0.115 3.271,0.406 3.156,0.292 12 false Reference (System Diagram of Sensor 1): 0.427,0.969 0.927,1.385 0.5,0.417 10 false from Battery 0.26,2.563 1.063,3 0.802,0.438 10 false from MAIN Relay 1.302,1.26 1.635,1.5 0.333,0.24 10 false A/F 2.281,2.125 2.615,2.365 0.333,0.24 10 false A/F 3.417,0.99 3.75,1.229 0.333,0.24 10 false +B 3.875,1.271 4.417,1.542 0.542,0.271 10 false Heater 3.854,1.938 4.396,2.208 0.542,0.271 10 false Sensor 3.49,2.396 4.948,2.698 1.458,0.302 10 false Air Fuel Ratio Sensor 3.365,1.667 3.802,1.969 0.438,0.302 10 false A1A- 4.49,1.667 4.927,1.969 0.438,0.302 10 false A1A+ 4.49,0.979 4.927,1.281 0.438,0.302 10 false HA1A 5.188,0.979 5.625,1.281 0.438,0.302 10 false HA1A 5.198,1.656 5.635,1.958 0.438,0.302 10 false A1A+ 5.198,2.885 5.635,3.188 0.438,0.302 10 false A1A- 6.385,1.802 6.896,2.24 0.51,0.438 10 false Duty Control 5.948,0.448 6.385,0.75 0.438,0.302 10 false ECM


Result:
Proceed to
OK
NG



OK

2.REPLACE AIR FUEL RATIO SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (AIR FUEL RATIO SENSOR - ECM)

2.REPLACE AIR FUEL RATIO SENSOR
a.

Result:
Proceed to
NEXT



NEXT

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P2237, P2238, P2239, P2252 OR P2253)
3.CHECK WHETHER DTC OUTPUT RECURS (DTC P2237, P2238, P2239, P2252 OR P2253)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Switch the ECM from normal mode to check mode.

Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>CHECK MODE PROCEDURE

Powertrain > Engine and ECT > Utility
Tester Display
Check Mode
50005 234 1

f.

Drive the vehicle according to Confirmation Driving Pattern.

Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>P2195


g.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine and ECT > Trouble Codes
50001 234

h.

Read the DTCs (Pending DTCs).

Result:
Result Proceed to
DTC is not output A
DTC P2237, P2238, P2239, P2252 or P2253 is output B




A

END

B