Home › Engine / Hybrid System › 2TR-FBE ENGINE CONTROL › SFI SYSTEM › from 2012.10
RM1840EF _51 Engine / Hybrid System _009571 2TR-FBE ENGINE CONTROL _0052126 SFI SYSTEM C

2TR-FBE ENGINE CONTROL  SFI SYSTEM  P2195  Oxygen (A/F) Sensor Signal Stuck Lean (Bank 1 Sensor 1)  P2196  Oxygen (A/F) Sensor Signal Stuck Rich (Bank 1 Sensor 1)  


DESCRIPTION

HINT:
·

Although the DTC titles say oxygen sensor, these DTCs relate to the air fuel ratio sensor.

·

Sensor 1 refers to the sensor mounted in front of the three way catalytic converter and located near the engine assembly.



The air fuel ratio sensor generates a voltage* that corresponds to the actual air fuel ratio. This sensor voltage is used to provide the ECM with feedback so that it can control the air fuel ratio. The ECM determines the deviation from the stoichiometric air fuel ratio and regulates the fuel injection time. If the air fuel ratio sensor malfunctions, the ECM is unable to control the air fuel ratio accurately.

The air fuel ratio sensor is of the planar type and is integrated with a heater, which heats the solid electrolyte (zirconia element). This heater is controlled by the ECM. When the intake air volume is low (the exhaust gas temperature is low), a current flows through the heater to heat the sensor in order to facilitate accurate air fuel ratio detection. The heat generated by the heater is conducted to the solid electrolyte through the alumina, thereby accelerating the sensor activation.

A three way catalytic converter is used in order to convert the carbon monoxide, hydrocarbons and nitrogen oxide into less harmful substances. To allow the three way catalytic converter to function effectively, it is necessary to keep the air fuel ratio of the engine near the stoichiometric air fuel ratio.

*: The value changes inside the ECM. Since the air fuel ratio sensor is a current output element, current is converted into a voltage inside the ECM. Any measurements taken at the air fuel ratio sensor or ECM connectors will show a constant voltage.

A225097
1.656,1.896 1.948,1.896 false 1.458,1.938 0.854,1.458 false 3.177,1.844 3.531,2.135 false 2.99,1.521 3.521,1.75 false 3.073,1.302 3.458,1.208 false 3.313,1.094 3.531,0.792 false 3.135,1.51 3.531,1.76 false 3.208,1.042 3.521,0.5 false 1.073,2.26 1.26,2.49 0.188,0.229 10 false A 1.781,2.25 1.969,2.469 0.188,0.219 10 false A 0.302,1.344 0.917,1.563 0.615,0.219 10 false Element 0.083,2.208 1.021,2.479 0.938,0.271 10 false Exhaust Gas 2.615,2.396 3.833,2.615 1.219,0.219 10 false A-A Cross Section 3.594,1.615 4.375,2.01 0.781,0.396 10 false Platinum Electrode 1.99,1.823 2.552,2.042 0.563,0.219 10 false Cover 3.583,2.104 4.688,2.302 1.104,0.198 10 false Atmospheric Air 3.573,0.698 4.135,0.917 0.563,0.219 10 false Heater 3.573,0.417 4.135,0.635 0.563,0.219 10 false Alumina 3.51,1.073 4.719,1.479 1.208,0.406 10 false Solid Electrolyte (Zirconia Element) 5.615,2.271 6.677,2.563 1.063,0.292 10 false Air Fuel Ratio 4.26,0.292 6.198,0.531 1.938,0.24 10 false Air Fuel Ratio Sensor Voltage 4.26,0.094 5.365,0.323 1.104,0.229 10 false ECM Monitored

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2195 Oxygen (A/F) Sensor Signal Stuck Lean (Bank 1 Sensor 1) Condition 1:
Conditions (a) and (b) are met for 10 seconds or more (2 trip detection logic):
(a) The air fuel ratio sensor voltage is higher than 3.8 V.
(b) The heated oxygen sensor voltage is 0.21 V or higher.
Condition 2:
While the fuel-cut operation is performed (during vehicle deceleration), the air fuel ratio sensor current is 3.6 mA or higher (2 trip detection logic).
Condition 1:
·

Open or short in air fuel ratio sensor circuit

·

Air fuel ratio sensor

·

Air fuel ratio sensor heater

·

Air fuel ratio sensor heater and relay circuits

·

Intake system

·

Fuel pressure

·

Fuel injector assembly

·

ECM


Condition 2:
·

Air fuel ratio sensor

·

ECM


Comes on DTC stored
P2196 Oxygen (A/F) Sensor Signal Stuck Rich (Bank 1 Sensor 1) Condition 1:
Conditions (a) and (b) are met for 10 seconds or more (2 trip detection logic):
(a) The air fuel ratio sensor voltage is below 2.8 V for 10 seconds.
(b) The heated oxygen sensor voltage is below 0.6 V.
Condition 2:
While the fuel-cut operation is performed (during vehicle deceleration), the air fuel ratio sensor current is below 0.78 mA (2 trip detection logic).
Condition 1:
·

Open or short in air fuel ratio sensor circuit

·

Air fuel ratio sensor

·

Air fuel ratio sensor heater

·

Air fuel ratio sensor heater and relay circuits

·

Intake system

·

Fuel pressure

·

Fuel injector assembly

·

ECM


Condition 2:
·

Air fuel ratio sensor

·

ECM


Comes on DTC stored

HINT:
·

When either of these DTCs is stored, check the air fuel ratio sensor output voltage using the intelligent tester. Enter the following menus: Powertrain / Engine and ECT / Data List / AFS Voltage B1S1.

·

Short-term fuel trim values can also be read using the intelligent tester.

·

The ECM maintains the voltages at the A1A+ and A1A- terminals of the ECM at a constant level. Therefore, the air fuel ratio sensor output voltage cannot be confirmed without using the intelligent tester.

·

If the air fuel ratio sensor is malfunctioning, the ECM stores DTC P2195 or P2196.



WIRING DIAGRAM

A262784
6.469,7.052 6.917,7.281 0.448,0.229 10 false ECM 0.594,5.323 1.354,5.563 0.76,0.24 10 false BATT P/I 1.833,1.917 2.354,2.135 0.521,0.219 10 false MAIN 0.781,6.177 1.365,6.427 0.583,0.25 10 false Battery 0.688,1.354 1.042,1.594 0.354,0.24 10 false EFI 3.063,6.5 3.948,6.771 0.885,0.271 10 false *: Shielded 5.406,2.292 5.583,2.458 0.177,0.167 10 false * 5.396,4.521 5.563,4.688 0.167,0.167 10 false * 3.99,3.302 4.344,3.604 0.354,0.302 10 false +B 4.448,3.302 4.979,3.521 0.531,0.219 10 false HA1A 4.51,4.25 4.958,4.51 0.448,0.26 10 false A1A- 4.469,3.771 4.917,4.01 0.448,0.24 10 false A1A+ 3.823,3.302 3.969,3.531 0.146,0.229 10 false 2 4.938,3.302 5.146,3.521 0.208,0.219 10 false 1 4.938,4.25 5.125,4.469 0.188,0.219 10 false 4 4.938,3.771 5.115,4.021 0.177,0.25 10 false 3 3.677,4.771 4.063,5 0.385,0.229 10 false C85 3.677,4.927 5.177,5.208 1.5,0.281 10 false Air Fuel Ratio Sensor 3.99,1.094 4.313,1.313 0.323,0.219 10 false +B 4.469,1.094 5.042,1.438 0.573,0.344 10 false HT1B 4.656,2.042 4.969,2.302 0.313,0.26 10 false E2 4.458,1.573 4.979,1.802 0.521,0.229 10 false OX1B 3.823,1.104 3.99,1.323 0.167,0.219 10 false 2 4.938,1.094 5.042,1.271 0.104,0.177 10 false 1 4.938,2.042 5.146,2.323 0.208,0.281 10 false 4 4.938,1.573 5.146,1.781 0.208,0.208 10 false 3 3.688,2.604 4.073,2.802 0.385,0.198 10 false C88 3.688,2.771 5.313,3.031 1.625,0.26 10 false Heated Oxygen Sensor 5.938,1.208 6.302,1.438 0.365,0.229 10 false C97 6.302,3.417 6.76,3.625 0.458,0.208 10 false HA1A 5.979,1.021 6.271,1.26 0.292,0.24 10 false 18 5.969,1.969 6.24,2.135 0.271,0.167 10 false 14 5.938,1.688 6.344,1.906 0.406,0.219 10 false C97 6.302,3.896 6.792,4.135 0.49,0.24 10 false A1A+ 5.979,1.5 6.281,1.729 0.302,0.229 10 false 13 5.938,2.156 6.354,2.375 0.417,0.219 10 false C97 6.302,4.365 6.76,4.604 0.458,0.24 10 false A1A- 5.948,3.417 6.344,3.615 0.396,0.198 10 false C97 6.302,1.198 6.802,1.438 0.5,0.24 10 false HT1B 6.021,3.229 6.208,3.448 0.188,0.219 10 false 6 5.948,3.896 6.333,4.104 0.385,0.208 10 false C97 6.302,1.677 6.823,1.917 0.521,0.24 10 false OX1B 6.031,3.698 6.208,3.927 0.177,0.229 10 false 7 5.938,4.365 6.323,4.604 0.385,0.24 10 false C97 6.302,2.146 6.844,2.385 0.542,0.24 10 false EX1B 6.01,4.177 6.177,4.396 0.167,0.219 10 false 1 5.896,5.792 6.333,6 0.438,0.208 10 false G146 6.302,5.802 6.792,6.083 0.49,0.281 10 false MREL 5.99,5.604 6.219,5.792 0.229,0.188 10 false 12 5.948,6.188 6.365,6.438 0.417,0.25 10 false C97 6.313,6.177 6.75,6.458 0.438,0.281 10 false E03 5.99,6.01 6.25,6.208 0.26,0.198 10 false 12 0.406,2.344 0.667,2.573 0.26,0.229 10 false 1H 0.688,2.344 0.896,2.573 0.208,0.229 10 false 1 1,2.354 1.25,2.594 0.25,0.24 10 false 1J 1.271,2.344 1.521,2.542 0.25,0.198 10 false 3 2.604,1.635 2.875,1.885 0.271,0.25 10 false 1J 2.646,1.448 2.792,1.656 0.146,0.208 10 false 2 1.833,2.563 2.969,2.844 1.135,0.281 10 false Integration Relay 5.948,6.604 6.323,6.854 0.375,0.25 10 false C97 6.302,6.583 6.667,6.802 0.365,0.219 10 false E04 5.99,6.406 6.24,6.625 0.25,0.219 10 false 23 1.906,4.125 2.25,4.427 0.344,0.302 10 false A/F 0.698,3.563 1.031,3.802 0.333,0.24 10 false A/F 2.604,1.208 2.896,1.438 0.292,0.229 10 false 1J 2.646,1.021 2.823,1.25 0.177,0.229 10 false 5 1.573,3.667 1.75,3.885 0.177,0.219 10 false 2 1.573,3.323 1.729,3.531 0.156,0.208 10 false 5 2.354,3.667 2.51,3.865 0.156,0.198 10 false 1 2.354,3.323 2.521,3.552 0.167,0.229 10 false 3

CONFIRMATION DRIVING PATTERN

This confirmation driving pattern is used in the "Perform Confirmation Driving Pattern" procedure of the following diagnostic troubleshooting procedure.

A232734
6.146,2.427 6.146,3.188 false 5.125,2.438 5.125,3.198 false 4.104,2.427 4.104,3.188 false 0.104,0.083 1.031,0.375 0.927,0.292 10 false Vehicle Speed 0.26,0.948 0.896,1.333 0.635,0.385 10 false 40 km/h (25 mph) 0.51,1.625 0.938,1.906 0.427,0.281 10 false Idling 0.177,1.938 0.854,2.531 0.677,0.594 10 false Ignition Switch ON 1.104,1.927 1.375,2.198 0.271,0.271 10 false [A] 1.594,1.594 1.875,1.865 0.281,0.271 10 false [B] 2.646,0.271 2.917,0.51 0.271,0.24 10 false [C] 4.521,1.594 4.792,1.885 0.271,0.292 10 false [E] 4.01,0.708 4.292,0.969 0.281,0.26 10 false [D] 5.552,1.594 5.833,1.865 0.281,0.271 10 false [E] 6.583,1.594 6.833,1.823 0.25,0.229 10 false [F] 1.333,2.521 2.104,2.844 0.771,0.323 10 false Warming up 2.24,2.542 3.458,2.833 1.219,0.292 10 false 20 minutes or more 4.26,2.51 5,3.135 0.74,0.625 10 false 30 seconds or more 5.281,2.49 6.021,3.146 0.74,0.656 10 false 30 seconds or more 5.813,3.188 6.573,3.625 0.76,0.438 10 false 20 seconds or more 6.323,2.49 7.063,2.875 0.74,0.385 10 false 40 seconds or more 5.031,0.708 5.313,0.969 0.281,0.26 10 false [D] 6.063,0.708 6.385,1 0.323,0.292 10 false [D] 4.823,3.188 5.583,3.635 0.76,0.448 10 false 20 seconds or more 3.771,3.167 4.531,3.615 0.76,0.448 10 false 20 seconds or more 0.26,0.417 0.896,0.792 0.635,0.375 10 false 60 km/h (37 mph)

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON [A].

3.

Turn the tester on.

5.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) [B].

6.

Drive the vehicle at 60 km/h (37 mph) or more for 20 minutes or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:
·

This step is performed to complete ethanol concentration learning.

·

If DTC P0136, P2195 or P2196 is output when any of the following conditions is met, it is necessary to complete ethanol concentration learning to meet preconditions.

·

The battery has been disconnected and reconnected.

·

The DTCs have been cleared.

·

Both fuel tank assemblies (for main and sub tanks) have been filled with fuel.




7.

Drive the vehicle at more than 40 km/h (25 mph) for 20 seconds or more [D].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


8.

Allow the engine to idle for 30 seconds or more [E].

9.

Repeat procedure [D] and [E] described above at least 3 times.

10.

Allow the engine to idle for 40 seconds or more [F].

11.

Enter the following menus: Powertrain / Engine and ECT / DTC / Pending.

12.

Read the pending DTCs.

HINT:

If a pending DTC is output, the system is malfunctioning.




CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Intelligent tester only:

Malfunctioning areas can be identified by performing the "Control the Injection Volume for A/F Sensor" function provided in the Active Test. The "Control the Injection Volume for A/F Sensor" function can help determine whether the air fuel ratio sensor, heated oxygen sensor and other potential trouble areas are malfunctioning.


The following instructions describe how to conduct the "Control the Injection Volume for A/F Sensor" operation using the intelligent tester.

1.

Connect the intelligent tester to the DLC3.

2.

Start the engine.

3.

Turn the tester on.

4.

Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.

5.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.

6.

Perform the "Control the Injection Volume for A/F Sensor" operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).

7.

Monitor the output voltages of the air fuel ratio and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2) displayed on the tester.


HINT:
·

The "Control the Injection Volume for A/F Sensor" operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

The sensors react in accordance with increases and decreases in the fuel injection volume.



Standard:
Tester Display
(Sensor)
Injection Volume Status Voltage
AFS Voltage B1S1
(Air fuel ratio sensor)
+12.5% Rich Below 3.1 V
-12.5% Lean Higher than 3.4 V
O2S B1S2
(Heated oxygen sensor)
+12.5% Rich Higher than 0.55 V
-12.5% Lean Below 0.4 V


NOTICE:

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor (sensor 2) output has a maximum output delay of approximately 20 seconds.


A301859
0.135,0.688 0.75,0.885 0.615,0.198 10 false Case 0.844,0.635 2.906,1.021 2.063,0.385 10 false Air Fuel Ratio Sensor (Sensor 1) Output Voltage 3.427,0.625 5.573,1 2.146,0.375 10 false Heated Oxygen Sensor (Sensor 2) Output Voltage 5.948,0.635 7.052,1.01 1.104,0.375 10 false Main Suspected Trouble Area 6.427,2.208 6.719,2.479 0.292,0.271 10 false - 0.24,2.198 0.448,2.458 0.208,0.26 10 false 1 0.26,4.292 0.469,4.552 0.208,0.26 10 false 2 0.26,6.344 0.469,6.604 0.208,0.26 10 false 3 0.26,8.396 0.469,8.656 0.208,0.26 10 false 4 1.385,1.594 2,1.792 0.615,0.198 8 false +12.5% 1.417,1.823 2.031,2.021 0.615,0.198 8 false -12.5% 0.583,2.281 1.573,2.5 0.99,0.219 9 false Output Voltage 0.594,1.333 1.75,1.667 1.156,0.333 9 false Injection Volume 0.865,2.646 2.042,2.917 1.177,0.271 8 false Higher than 3.4 V 1.115,2.865 1.906,3.104 0.792,0.24 8 false Below 3.1 V 2.521,2.76 2.823,3.01 0.302,0.25 8 false OK 1.417,3.885 2.031,4.083 0.615,0.198 8 false -12.5% 1.396,3.656 2.01,3.854 0.615,0.198 8 false +12.5% 0.583,3.417 1.75,3.667 1.167,0.25 9 false Injection Volume 0.583,4.333 1.854,4.594 1.271,0.26 9 false Output Voltage 0.875,4.802 1.875,5.01 1,0.208 8 false Almost no reaction 2.552,4.719 2.938,5 0.385,0.281 8 false NG 1.427,5.938 2.042,6.135 0.615,0.198 8 false -12.5% 1.406,5.729 2.021,5.927 0.615,0.198 8 false +12.5% 0.583,5.469 1.677,5.667 1.094,0.198 9 false Injection Volume 0.583,6.417 1.635,6.656 1.052,0.24 9 false Output Voltage 0.865,6.76 1.917,6.917 1.052,0.156 8 false Higher than 3.4 V 1.115,6.979 1.906,7.219 0.792,0.24 8 false Below 3.1 V 2.531,6.865 2.833,7.115 0.302,0.25 8 false OK 0.583,7.5 1.583,7.708 1,0.208 9 false Injection Volume 1.427,8.01 2.042,8.208 0.615,0.198 8 false -12.5% 1.396,7.802 2.01,8 0.615,0.198 8 false +12.5% 0.583,8.438 1.635,8.667 1.052,0.229 9 false Output Voltage 0.865,8.927 1.823,9.125 0.958,0.198 8 false Almost no reaction 2.563,8.854 2.948,9.135 0.385,0.281 8 false NG 3.25,1.333 4.427,1.635 1.177,0.302 9 false Injection Volume 4.021,1.594 4.635,1.792 0.615,0.198 8 false +12.5% 4.042,1.813 4.656,2.01 0.615,0.198 8 false -12.5% 3.25,2.271 4.281,2.5 1.031,0.229 9 false Output Voltage 3.49,2.604 4.667,2.813 1.177,0.208 8 false Higher than 0.55 V 3.813,2.844 4.604,3.083 0.792,0.24 8 false Below 0.4 V 5.198,2.708 5.5,2.958 0.302,0.25 8 false OK 3.25,3.417 4.427,3.604 1.177,0.188 9 false Injection Volume 4.042,3.875 4.656,4.073 0.615,0.198 8 false -12.5% 4.01,3.667 4.625,3.865 0.615,0.198 8 false +12.5% 3.25,4.333 4.396,4.583 1.146,0.25 9 false Output Voltage 3.448,4.698 4.521,4.917 1.073,0.219 8 false Higher than 0.55 V 3.76,4.927 4.594,5.167 0.833,0.24 8 false Below 0.4 V 5.208,4.813 5.51,5.063 0.302,0.25 8 false OK 6.083,3.615 6.906,4.01 0.823,0.396 8 false Air fuel ratio sensor 6.094,4 6.854,4.573 0.76,0.573 8 false Air fuel ratio sensor heater 6.083,4.563 6.844,5.146 0.76,0.583 8 false Air fuel ratio sensor circuit 5.917,3.604 6.083,3.792 0.167,0.188 10 false - 5.917,3.99 6.083,4.177 0.167,0.188 10 false - 5.917,4.542 6.083,4.729 0.167,0.188 10 false - 4.042,5.948 4.656,6.146 0.615,0.198 8 false -12.5% 4.021,5.75 4.635,5.948 0.615,0.198 8 false +12.5% 3.25,5.469 4.354,5.729 1.104,0.26 9 false Injection Volume 3.25,6.417 4.198,6.667 0.948,0.25 9 false Output Voltage 3.5,6.865 4.552,7.052 1.052,0.188 8 false Almost no reaction 5.177,6.781 5.563,7.063 0.385,0.281 8 false NG 3.25,7.5 4.417,7.698 1.167,0.198 9 false Injection Volume 4.031,8 4.646,8.198 0.615,0.198 8 false -12.5% 4.01,7.813 4.625,8.01 0.615,0.198 8 false +12.5% 3.479,8.938 4.521,9.104 1.042,0.167 8 false Almost no reaction 5.156,8.854 5.542,9.135 0.385,0.281 8 false NG 3.26,8.417 4.333,8.667 1.073,0.25 9 false Output Voltage 6.083,5.438 6.927,5.75 0.844,0.313 8 false Heated oxygen sensor 6.073,5.958 6.896,6.333 0.823,0.375 8 false Heated oxygen sensor heater 6.073,6.646 6.917,7.25 0.844,0.604 8 false Heated oxygen sensor circuit 5.917,5.948 6.083,6.135 0.167,0.188 10 false - 5.917,5.417 6.083,5.604 0.167,0.188 10 false - 5.917,6.615 6.083,6.802 0.167,0.188 10 false - 6.083,7.531 6.948,7.906 0.865,0.375 8 false Fuel injector assembly 6.083,7.917 6.833,8.167 0.75,0.25 8 false Fuel pressure 6.094,8.177 6.917,9.281 0.823,1.104 8 false Gas leak from exhaust system (air-fuel ratio extremely rich or lean) 5.917,7.521 6.083,7.708 0.167,0.188 10 false - 5.917,7.906 6.083,8.094 0.167,0.188 10 false - 5.917,8.156 6.083,8.344 0.167,0.188 10 false -

Following the "Control the Injection Volume for A/F Sensor" procedure enables technicians to check and graph the voltage outputs of both the air fuel ratio and heated oxygen sensors.

To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / View / AFS Voltage B1S1 and O2S B1S2.


HINT:
·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

A low air fuel ratio sensor voltage could be caused by a rich air fuel mixture. Check for conditions that would cause the engine to run rich.

·

A high air fuel ratio sensor voltage could be caused by a lean air fuel mixture. Check for conditions that would cause the engine to run lean.



PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO P2195 OR P2196)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine and ECT > Trouble Codes
50001 234

e.

Read the DTCs.

Result:
Result Proceed to
P2195 or P2196 is output A
"P2195 or P2196" and "P0136, P0137 or P0138" are output
P2195 or P2196 and other DTCs are output B


HINT:

If any DTCs relating to the air fuel ratio sensor (DTCs for the air fuel ratio sensor heater or air fuel ratio sensor admittance) are output, troubleshoot those DTCs first.




A

2.READ VALUE USING INTELLIGENT TESTER (TEST VALUE OF AIR FUEL RATIO SENSOR)

B

2.READ VALUE USING INTELLIGENT TESTER (TEST VALUE OF AIR FUEL RATIO SENSOR)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


f.

Enter the following menus: Powertrain / Engine and ECT / Utility / Monitor Status.


g.

Check that the status of "O2 Sensor" is "Complete". If the status is still "Incomplete", drive the vehicle according to the driving pattern again.

HINT:
·

"Available" indicates that the component has not been monitored yet.

·

"Complete" indicates that the component is functioning normally.

·

"Incomplete" indicates that the component is malfunctioning.




h.

Enter the following menus: Powertrain / Engine and ECT / Data List / AFS Current B1S1.

Powertrain > Engine and ECT > Data List
Tester Display
AFS Current B1S1
50003 234 39

i.

Check the test value of the air fuel ratio sensor output current during fuel-cut (refer to Confirmation Driving Pattern).

Result:
Test Value Proceed to
Within normal range (0.78 mA or higher, and below 3.6 mA) A
Outside normal range (Below 0.78 mA, or 3.6 mA or higher) B




A

3.READ VALUE USING INTELLIGENT TESTER (OUTPUT VOLTAGE OF AIR FUEL RATIO SENSOR)

B

14.REPLACE AIR FUEL RATIO SENSOR
3.READ VALUE USING INTELLIGENT TESTER (OUTPUT VOLTAGE OF AIR FUEL RATIO SENSOR)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the tester on.


d.

Warm up the air fuel ratio sensor at an engine speed of 2500 rpm for 90 seconds.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / AFS Voltage B1S1 and Engine Speed / Function / Snap Shot Record.

Powertrain > Engine and ECT > Data List
Tester Display
Engine Speed
AFS Voltage B1S1
50003 234 9,35

f.

Check the air fuel ratio sensor voltage 3 times, once under each of the following conditions:

i.

Engine idling (for at least 30 seconds) (Step "A").


ii.

Engine running at an engine speed of approximately 2500 rpm (without any sudden changes in engine speed) (Step "B").


iii.

Engine speed to raised 4000 rpm and then accelerator pedal quickly released so that throttle valve is fully closed (Step "C").

Standard Voltage:
Condition A/F Sensor Voltage Variation Reference
Step "A" and Step "B" Remains at approximately 3.3 V Between 3.1 V and 3.5 V
Step "C" Increases to 3.8 V or higher Occurs during engine deceleration
(when fuel-cut performed)


HINT:
·

For more information, see the diagrams below.

A107161
2.635,1.594 2.781,0.698 false 1.688,1.844 1.469,1.094 false 1.146,1.958 1.219,1.708 false 3.021,1.969 3.094,1.719 false 2.708,2.375 2.865,3.021 false 2.708,2.813 2.552,2.917 false 1.49,2.521 1.156,3.01 1.156,3.01 1.76,2.563 false 5.115,2.542 5.021,3.052 false 5.333,1.823 5.49,1.156 false 6.229,1.594 6.417,0.677 false 4.688,1.969 4.781,1.688 false 6.583,1.979 6.667,1.698 false 0.052,0.094 1.781,0.406 1.729,0.313 12 false Normal Condition: 1.625,0.479 3.49,0.76 1.865,0.281 10 false (3) Approximately 4000 rpm 0.24,0.875 2.104,1.156 1.865,0.281 10 false (2) Approximately 2500 rpm 0.99,1.479 1.615,1.74 0.625,0.26 10 false (1) Idling 2.76,1.49 3.385,1.75 0.625,0.26 10 false (1) Idling 0.052,1.906 0.958,2.146 0.906,0.24 10 false Engine Speed 0.188,2.365 0.948,2.76 0.76,0.396 10 false A/F Sensor Voltage 0.146,3.052 1.438,3.302 1.292,0.25 10 false "Condition (A), (B)": 0.156,3.229 2.198,3.469 2.042,0.24 10 false Remains at approximately 3.3 V 2.031,2.844 2.635,3.073 0.604,0.229 10 false Fuel-cut 2.573,3.052 3.583,3.469 1.01,0.417 10 false "Condition (C)": 3.8 V or higher 3.771,2.375 4.531,2.771 0.76,0.396 10 false A/F Sensor Voltage 3.625,1.885 4.531,2.125 0.906,0.24 10 false Engine Speed 4.573,1.469 5.198,1.729 0.625,0.26 10 false (1) Idling 6.354,1.479 6.979,1.74 0.625,0.26 10 false (1) Idling 5.219,0.458 7.083,0.74 1.865,0.281 10 false (3) Approximately 4000 rpm 4.51,0.896 6.375,1.177 1.865,0.281 10 false (2) Approximately 2500 rpm 6.073,2.854 6.667,3.083 0.594,0.229 10 false Fuel-cut 3.833,3.083 6.333,3.5 2.5,0.417 10 false When A/F sensor circuit malfunctioning, voltage output does not change 3.688,0.104 4.917,0.417 1.229,0.313 12 false Malfunctioning:

·

If the output voltage of the air fuel ratio sensor remains at approximately 3.3 V (see "Malfunctioning" diagram) under any conditions, including those above, the air fuel ratio sensor may have an open circuit (this will also happen if the air fuel ratio sensor heater has an open circuit).

·

If the output voltage of the air fuel ratio sensor remains at either approximately 3.8 V or higher, or 2.8 V or less (see "Malfunctioning" diagram) under any conditions, including those above, the air fuel ratio sensor may have a short circuit.

·

The ECM stops fuel injection (fuel cut) during engine deceleration. This causes a lean condition and results in a momentary increase in the air fuel ratio sensor output voltage.

·

The ECM must establish a closed throttle valve position learned value to perform fuel cut. If the battery cable has been disconnected and reconnected, the vehicle must be driven over 16 km/h (10 mph) to allow the ECM to learn the closed throttle valve position.

·

When the vehicle is driven:

The output voltage of the air fuel ratio sensor may be below 2.8 V during fuel enrichment. For the vehicle, this translates to a sudden increase in speed with the accelerator pedal fully depressed when trying to overtake another vehicle. The air fuel ratio sensor is functioning normally.

·

The air fuel ratio sensor is a current output element. Therefore, the current is converted into a voltage inside the ECM. Measuring the voltage at the connectors of the air fuel ratio sensor or ECM will show a constant voltage.





Result:
Proceed to
OK
NG



OK

4.PERFORM CONFIRMATION DRIVING PATTERN

NG

9.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)
4.PERFORM CONFIRMATION DRIVING PATTERN
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON and turn the intelligent tester on.


g.

Start the engine and warm it up.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)
5.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)
a.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine and ECT > Utility
Tester Display
All Readiness
50005 234 20

b.

Input the DTC: P2195 or P2196.


c.

Check the DTC judgment result.

Result:
Result Proceed to
ABNORMAL (DTC P2195 or P2196 is output) A
NORMAL (DTC is not output) B




A

6.REPLACE AIR FUEL RATIO SENSOR

B

17.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST
6.REPLACE AIR FUEL RATIO SENSOR
a.

Result:
Proceed to
NEXT



NEXT

7.PERFORM CONFIRMATION DRIVING PATTERN
7.PERFORM CONFIRMATION DRIVING PATTERN
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON and turn the intelligent tester on.


g.

Start the engine and warm it up.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


Result:
Proceed to
NEXT



NEXT

8.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)
8.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)
a.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine and ECT > Utility
Tester Display
All Readiness
50005 234 20

b.

Input the DTC: P2195 or P2196.


c.

Check the DTC judgment result.

Result:
Result Proceed to
ABNORMAL (DTC P2195 or P2196 is output) A
NORMAL (DTC is not output) B




A

END

B

9.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)

Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)

NG

10.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
a.

Disconnect the air fuel ratio sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C85-2 (+B) - Body ground Ignition switch ON 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C85-1 (HA1A) - C97-6 (HA1A) Always Below 1 Ω
C85-3 (A1A+) - C97-7 (A1A+) Always Below 1 Ω
C85-4 (A1A-) - C97-1 (A1A-) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C85-1 (HA1A) or C97-6 (HA1A) - Body ground Always 10 kΩ or higher
C85-3 (A1A+) or C97-7 (A1A+) - Body ground Always 10 kΩ or higher
C85-4 (A1A-) or C97-1 (A1A-) - Body ground Always 10 kΩ or higher



e.

Reconnect the ECM connector.


f.

Reconnect the air fuel ratio sensor connector.

A227661
0.115,0.115 3.271,0.406 3.156,0.292 12 false Reference (System Diagram of Sensor 1): 0.427,0.969 0.927,1.385 0.5,0.417 10 false from Battery 0.26,2.563 1.063,3 0.802,0.438 10 false from MAIN Relay 1.302,1.26 1.635,1.5 0.333,0.24 10 false A/F 2.281,2.125 2.615,2.365 0.333,0.24 10 false A/F 3.417,0.99 3.75,1.229 0.333,0.24 10 false +B 3.875,1.271 4.417,1.542 0.542,0.271 10 false Heater 3.854,1.938 4.396,2.208 0.542,0.271 10 false Sensor 3.49,2.396 4.948,2.698 1.458,0.302 10 false Air Fuel Ratio Sensor 3.365,1.667 3.802,1.969 0.438,0.302 10 false A1A- 4.49,1.667 4.927,1.969 0.438,0.302 10 false A1A+ 4.49,0.979 4.927,1.281 0.438,0.302 10 false HA1A 5.188,0.979 5.625,1.281 0.438,0.302 10 false HA1A 5.198,1.656 5.635,1.958 0.438,0.302 10 false A1A+ 5.198,2.885 5.635,3.188 0.438,0.302 10 false A1A- 6.385,1.802 6.896,2.24 0.51,0.438 10 false Duty Control 5.948,0.448 6.385,0.75 0.438,0.302 10 false ECM


Result:
Proceed to
OK
NG



OK

11.CHECK AIR INDUCTION SYSTEM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (AIR FUEL RATIO SENSOR - ECM)

11.CHECK AIR INDUCTION SYSTEM
a.

Check the air induction system for vacuum leakage.

OK:

No leakage from air induction system.



Result:
Proceed to
OK
NG



OK

12.CHECK FUEL PRESSURE

NG

REPAIR OR REPLACE AIR INDUCTION SYSTEM

12.CHECK FUEL PRESSURE

Result:
Proceed to
OK
NG



OK

13.INSPECT FUEL INJECTOR ASSEMBLY

NG

REPAIR OR REPLACE FUEL SYSTEM

13.INSPECT FUEL INJECTOR ASSEMBLY
a.

Check the injector injection (whether fuel volume is high or low, and whether injection pattern is poor).

Click hereEngine / Hybrid System>2TR-FBE FUEL>FUEL INJECTOR>INSPECTION


Result:
Proceed to
OK
NG



OK

14.REPLACE AIR FUEL RATIO SENSOR

NG

REPLACE FUEL INJECTOR ASSEMBLY

14.REPLACE AIR FUEL RATIO SENSOR
a.

Result:
Proceed to
NEXT



NEXT

15.PERFORM CONFIRMATION DRIVING PATTERN
15.PERFORM CONFIRMATION DRIVING PATTERN
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON and turn the intelligent tester on.


g.

Start the engine and warm it up.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


Result:
Proceed to
NEXT



NEXT

16.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)
16.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)
a.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine and ECT > Utility
Tester Display
All Readiness
50005 234 20

b.

Input the DTC: P2195 or P2196.


c.

Check the DTC judgment result.

Result:
Result Proceed to
ABNORMAL (DTC P2195 or P2196 is output) A
NORMAL (DTC is not output) B




A

END

B

17.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST
a.

Has the vehicle run out of fuel in the past?

Result:
Proceed to
YES
NO




YES

DTC CAUSED BY RUNNING OUT OF FUEL

NO