Home › Engine / Hybrid System › 2TR-FBE ENGINE CONTROL › SFI SYSTEM › from 2012.10
RM1840EF _51 Engine / Hybrid System _009571 2TR-FBE ENGINE CONTROL _0052126 SFI SYSTEM J

2TR-FBE ENGINE CONTROL  SFI SYSTEM  Fuel Injector Circuit  


DESCRIPTION

The fuel injectors are located on the intake manifold. They inject fuel into the cylinders based on the signals from the ECM.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK FUEL INJECTOR ASSEMBLY (POWER SOURCE)
a.
A206908
0.458,0.615 0.823,0.844 0.365,0.229 0.458,0.927 0.823,1.156 0.365,0.229 0.458,1.25 0.823,1.479 0.365,0.229 0.458,1.573 0.823,1.802 0.365,0.229 0.125,0.073 0.479,0.333 0.354,0.26 10 false *a 0.521,0.656 0.875,0.917 0.354,0.26 10 false C65 0.552,0.969 0.906,1.229 0.354,0.26 10 false C2 0.51,1.292 0.865,1.552 0.354,0.26 10 false C66 0.563,1.604 0.917,1.865 0.354,0.26 10 false C4
*a Front view of wire harness connector
(to Fuel Injector Assembly)


Disconnect the fuel injector assembly connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C65-1 - Body ground Ignition switch ON 11 to 14 V
C2-1 - Body ground Ignition switch ON 11 to 14 V
C66-1 - Body ground Ignition switch ON 11 to 14 V
C4-1 - Body ground Ignition switch ON 11 to 14 V



c.

Turn the ignition switch off.


d.

Reconnect the fuel injector assembly connectors.


Result:
Proceed to
OK
NG



OK

2.INSPECT FUEL INJECTOR ASSEMBLY

NG

4.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - FUEL INJECTOR ASSEMBLY)
2.INSPECT FUEL INJECTOR ASSEMBLY
a.

Inspect the fuel injector assembly.

Click hereEngine / Hybrid System>2TR-FBE FUEL>FUEL INJECTOR>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM)

NG

REPLACE FUEL INJECTOR ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM)
a.

Disconnect the fuel injector assembly connectors.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C65-2 - C98-6 (#10) Always Below 1 Ω
C2-2 - C98-7 (#20) Always Below 1 Ω
C66-2 - C98-8 (#30) Always Below 1 Ω
C4-2 - C98-9 (#40) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C65-2 or C98-6 (#10) - Body ground Always 10 kΩ or higher
C2-2 or C98-7 (#20) - Body ground Always 10 kΩ or higher
C66-2 or C98-8 (#30) - Body ground Always 10 kΩ or higher
C4-2 or C98-9 (#40) - Body ground Always 10 kΩ or higher



d.

Reconnect the fuel injector assembly connectors.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - FUEL INJECTOR ASSEMBLY)
a.

Disconnect the fuel injector assembly connectors.


b.

Disconnect the ignition switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C65-1 - G9-6 (IG2) Always Below 1 Ω
C2-1 - G9-6 (IG2) Always Below 1 Ω
C66-1 - G9-6 (IG2) Always Below 1 Ω
C4-1 - G9-6 (IG2) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C65-1 or G9-6 (IG2) - Body ground Always 10 kΩ or higher
C2-1 or G9-6 (IG2) - Body ground Always 10 kΩ or higher
C66-1 or G9-6 (IG2) - Body ground Always 10 kΩ or higher
C4-1 or G9-6 (IG2) - Body ground Always 10 kΩ or higher



d.

Reconnect the fuel injector connector.


e.

Reconnect the ignition switch connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR