The fuel injectors are located on the cylinder head. They inject fuel into the cylinders based on the signals from the ECM.
Inspect the fuses for circuits related to this system before performing the following procedure.
| *a | Front view of wire harness connector
(to Fuel Injector Assembly) |
Disconnect the fuel injector connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Cylinder | Tester Connection | Switch Condition | Specified Condition |
|---|---|---|---|
| No. 1 | C65-1 - Body ground | Ignition switch ON | 11 to 14 V |
| No. 2 | C2-1 - Body ground | Ignition switch ON | 11 to 14 V |
| No. 3 | C66-1 - Body ground | Ignition switch ON | 11 to 14 V |
| No. 4 | C4-1 - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the fuel injector assembly.
Click hereEngine / Hybrid System>2TR-FE FUEL>FUEL INJECTOR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the fuel injector connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Cylinder | Tester Connection | Condition | Specified Condition |
|---|---|---|---|
| No. 1 | C65-2 - Body ground | Always | 10 kΩ or higher |
| C65-2 - C76-6 (#10) | Always | Below 1 Ω | |
| No. 2 | C2-2 - Body ground | Always | 10 kΩ or higher |
| C2-2 - C76-5 (#20) | Always | Below 1 Ω | |
| No. 3 | C66-2 - Body ground | Always | 10 kΩ or higher |
| C66-2 - C76-2 (#30) | Always | Below 1 Ω | |
| No. 4 | C4-2 - Body ground | Always | 10 kΩ or higher |
| C4-2 - C76-1 (#40) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the fuel injector connector.
Disconnect the ignition switch connector.
Measure the resistance according to the value(s) in the table below.
| Cylinder | Tester Connection | Condition | Specified Condition |
|---|---|---|---|
| No. 1 | C65-1 - Body ground | Always | 10 kΩ or higher |
| C65-1 - G9-6 (IG2) | Always | Below 1 Ω | |
| No. 2 | C2-1 - Body ground | Always | 10 kΩ or higher |
| C2-1 - G9-6 (IG2) | Always | Below 1 Ω | |
| No. 3 | C66-1 - Body ground | Always | 10 kΩ or higher |
| C66-1 - G9-6 (IG2) | Always | Below 1 Ω | |
| No. 4 | C4-1 - Body ground | Always | 10 kΩ or higher |
| C4-1 - G9-6 (IG2) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the ignition switch assembly.
Click hereEngine / Hybrid System>2TR-FE STARTING>IGNITION SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG