Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM(w/o EGR Cooler) › 2012.04–2012.10
RM1840EF _51 Engine / Hybrid System _009570 1KD-FTV ENGINE CONTROL _0052103 ECD SYSTEM(w/o EGR Cooler) C

1KD-FTV ENGINE CONTROL  ECD SYSTEM(w/o EGR Cooler)  P0105  Manifold Absolute Pressure / Barometric Pressure Circuit  P0107  Manifold Absolute Pressure / Barometric Pressure Circuit Low Input  P0108  Manifold Absolute Pressure / Barometric Pressure Circuit High Input  


DESCRIPTION

A208461
0.417,0.479 0.583,0.656 0.167,0.177 10 false V 0.25,0.813 0.656,1.01 0.406,0.198 10 false 3.586 0.26,1.885 0.698,2.083 0.438,0.198 10 false 0.386 1.031,2.313 1.25,2.521 0.219,0.208 10 false 40 2.281,2.302 2.583,2.5 0.302,0.198 10 false 320 0.99,2.667 1.292,2.854 0.302,0.188 10 false 300 0.938,2.833 1.396,3.083 0.458,0.25 10 false (11.8) 2.24,2.844 2.688,3.115 0.448,0.271 10 false (94.5) 2.896,2.844 3.354,3.063 0.458,0.219 10 false (in.Hg) 2.896,2.531 3.354,2.75 0.458,0.219 10 false mmHg 2.896,2.073 3.229,2.25 0.333,0.177 10 false kPa 2.896,2.26 3.313,2.521 0.417,0.26 10 false (abs) 2.281,2.677 2.615,2.823 0.333,0.146 10 false 2400 1.323,3.073 2.177,3.281 0.854,0.208 10 false Air Pressure

The manifold absolute pressure sensor detects the intake manifold pressure. The ECM determines the basic injection volume and injection advance timing based on the voltage output by the manifold absolute pressure sensor.

The manifold absolute pressure sensor monitors the absolute pressure inside the intake manifold (default is 0 kPa [0 mmHg, 0 in.Hg]). As a result, the ECM controls the air-fuel ratio so that it reaches the proper level under any driving conditions.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0105 Manifold Absolute Pressure / Barometric Pressure Circuit After the engine is started, condition (a) continues for more than 2.0 seconds (1 trip detection logic):
(a) Manifold absolute pressure sensor voltage is 0.1 V or less, or 4.8 V or more.
·

Open or short in manifold absolute pressure sensor circuit

·

Manifold absolute pressure sensor

·

ECM


Comes on DTC stored
P0107 Manifold Absolute Pressure / Barometric Pressure Circuit Low Input After the engine is started, condition (a) continues for more than 0.5 seconds (1 trip detection logic):
(a) Manifold absolute pressure sensor voltage is 0.1 V or less.
·

Open or short in manifold absolute pressure sensor circuit

·

Manifold absolute pressure sensor

·

ECM


Comes on DTC stored
P0108 Manifold Absolute Pressure / Barometric Pressure Circuit High Input After the engine is started, condition (a) continues for more than 0.5 seconds (1 trip detection logic):
(a) Manifold absolute pressure sensor voltage is 4.8 V or higher.
·

Open or short in manifold absolute pressure sensor circuit

·

Manifold absolute pressure sensor

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P0105
·

MAP

·

Atmosphere Pressure


P0107
P0108

HINT:
·

If DTC P0105, P0107 and/or P0108 is stored, the following symptoms may appear:

·

Misfire

·

Combustion noise

·

Black smoke

·

White smoke

·

Lack of power


·

When DTC P0105, P0107 and/or P0108 is stored, check the intake manifold pressure by entering the following menus: Powertrain / Engine and ECT / Data List / MAP.

Reference
Intake Manifold Pressure Malfunction
Approximately 0 kPa
·

Open in VC circuit

·

Short in PIM circuit


250 kPa (1875 mmHg, 73.8 in.Hg) or higher
·

Open in PIM circuit

·

Open in E circuit





CONFIRMATION DRIVING PATTERN

P0105, P0107, P0108
DTC Detection Drive Pattern 2 seconds after engine is started, race engine for 1 second

WIRING DIAGRAM

A255069
0.615,2.292 2.885,2.521 2.271,0.229 10 false Manifold Absolute Pressure Sensor 0.615,2.146 0.938,2.344 0.323,0.198 10 false C20 6.083,2.146 6.479,2.313 0.396,0.167 10 false ECM 1.521,0.583 1.792,0.75 0.271,0.167 10 false VC 5.688,0.469 5.958,0.635 0.271,0.167 10 false VC 1.49,1.135 1.813,1.292 0.323,0.156 10 false PIM 5.667,1.042 5.99,1.198 0.323,0.156 10 false PIM 1.615,1.677 1.781,1.833 0.167,0.156 10 false E 5.688,1.583 5.917,1.771 0.229,0.188 10 false E2 6.177,0.333 6.458,0.51 0.281,0.177 10 false 5 V 1.823,0.667 1.948,0.854 0.125,0.188 10 false 3 1.833,1.24 1.958,1.427 0.125,0.188 10 false 2 1.823,1.771 1.948,1.958 0.125,0.188 10 false 1 5.385,0.385 5.583,0.542 0.198,0.156 10 false 18 5.385,0.948 5.583,1.104 0.198,0.156 10 false 28 5.385,1.479 5.583,1.635 0.198,0.156 10 false 28 5.333,0.563 5.646,0.74 0.313,0.177 10 false C22 5.333,1.677 5.646,1.854 0.313,0.177 10 false C22 5.333,1.135 5.656,1.302 0.323,0.167 10 false C23

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>INITIALIZATION).


HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (MANIFOLD ABSOLUTE PRESSURE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / MAP.

Powertrain > Engine > Data List
Tester Display
MAP
50003 61 314

d.

Read the value.

OK:

Same as the actual atmospheric pressure.


HINT:
·

Standard atmospheric pressure is 101 kPa. For every 100 m increase in elevation, pressure drops by 1 kPa. This varies by weather (high atmospheric pressure, low atmospheric pressure).

·

Also, check "Atmosphere Pressure" in the Data List.




Result:
Proceed to
OK
NG



OK

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

2.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
2.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
a.

Disconnect the manifold absolute pressure sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C20-2 (PIM) - C23-28 (PIM) Always Below 1 Ω
C20-3 (VC) - C22-18 (VC) Always Below 1 Ω
C20-1 (E) - C22-28 (E2) Always Below 1 Ω
C20-2 (PIM) or C23-28 (PIM) - Body ground Always 10 kΩ or higher
C20-3 (VC) or C22-18 (VC) - Body ground Always 10 kΩ or higher



d.

Reconnect the manifold absolute pressure sensor connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

3.CHECK ECM TERMINAL VOLTAGE (VC TERMINAL)

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK ECM TERMINAL VOLTAGE (VC TERMINAL)
a.
A204467C09
0.677,1.135 1.042,1.385 0.365,0.25 1.24,1.75 1.49,1.292 true 2.177,1.729 1.948,1.292 true 0.167,0.208 0.479,0.406 0.313,0.198 10 false *a 0.729,1.177 1.052,1.375 0.323,0.198 10 false C20 1.177,1.75 1.479,2 0.302,0.25 10 false E 2.198,1.74 2.51,1.938 0.313,0.198 10 false VC
*a Front view of wire harness connector
(to Absolute Pressure Sensor)


Disconnect the manifold absolute pressure sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C20-3 (VC) - C20-1 (E) Ignition switch ON 4.75 to 5.25 V



c.

Reconnect the manifold absolute pressure sensor connector.


Result:
Proceed to
OK
NG



OK

4.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

NG

6.REPLACE ECM
4.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (DTC P0105, P0107 OR P0108)
5.CHECK WHETHER DTC OUTPUT RECURS (DTC P0105, P0107 OR P0108)
a.

Connect the intelligent tester to the DLC3.


b.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the tester off.


e.

Start the engine.


f.

After the engine is started for 2 seconds, race the engine for 1 second.


g.

Turn the tester on.


h.

Confirm that the DTC is not output again.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 61 20

j.

Input DTC P0105, P0107 or P0108.


k.

Check the DTC judgment result.

Result:
Result Proceed to
ABNORMAL A
NORMAL B


HINT:

If STATUS is INCOMPLETE or N/A, race the engine for 1 minute, and then idle the engine for 5 minutes.




A

6.REPLACE ECM

B

END

6.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.


b.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the tester off.


e.

Turn the ignition switch to ON for 3 seconds and turn the tester on.


f.

After the engine is started for 2 seconds, race the engine for 1 second.


g.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the tester to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 61 20

ii.

Input DTC P0105, P0107 or P0108.


iii.

Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, race the engine for 1 minute, and then idle the engine for 5 minutes.



Result:
Proceed to
NEXT



NEXT

END