Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM(w/o EGR Cooler) › 2012.04–2012.10
RM1840EF _51 Engine / Hybrid System _009570 1KD-FTV ENGINE CONTROL _0052103 ECD SYSTEM(w/o EGR Cooler) C

1KD-FTV ENGINE CONTROL  ECD SYSTEM(w/o EGR Cooler)  P0400  Exhaust Gas Recirculation Flow  


DESCRIPTION

The EGR system recirculates exhaust gases, and performs control so that the proper volume of exhaust gas is recirculated to suit all driving conditions. The recirculated gas mixes with the intake air, allowing the EGR system to slow down engine combustion and lower the combustion temperature. This helps reduce NOx emissions.

In order to increase circulation efficiency, the ECM adjusts the lift amount of the EGR valve and throttle valve.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0400 Exhaust Gas Recirculation Flow Mass air flow rate is not changed when the EGR valve is turned on (1 trip detection logic).
·

EGR valve stuck

·

EGR valve does not move smoothly

·

Electric vacuum regulating valve assembly

·

Vacuum switching valve (for EGR Cut)

·

Electric vacuum regulating valve assembly circuit

·

Vacuum switching valve (for EGR Cut) circuit

·

EGR blockage in line between exhaust manifold and intake manifold

·

Mass air flow meter

·

Intake system (leaks or blockages)

·

Exhaust system (exhaust gas leaks)

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P0400
·

MAF

·

MAP

·

Actual EGR Valve Pos.

·

Target EGR Position

·

EGR Close Lrn. Val.

·

EGR Close Learn Val.

·

EGR Close Lrn. Status



CONFIRMATION DRIVING PATTERN

P0400
DTC Detection Drive Pattern Decelerate from a speed of 80 km/h (50 mph) or more (release accelerator pedal for approximately 5 seconds)

MONITOR DESCRIPTION

If the electric EGR control valve assembly is forcibly operated but the intake air amount does not vary, the ECM determines that the electric EGR control valve assembly is malfunctioning. The ECM then illuminates the MIL.


Flow malfunction

If the EGR valve is forcibly operated during deceleration but the intake air amount does not vary, the ECM determines that the EGR valve is malfunctioning. The ECM then illuminates the MIL (2 trip detection logic).


A194528
3.208,2.323 3.313,2.021 3.313,2.021 3.438,2.021 false 3.24,0.74 3.344,0.438 3.344,0.438 3.469,0.438 false 5.052,3.521 5.354,3.521 false 5.094,4.292 5.281,4.188 5.281,4.188 5.354,4.188 false 4.792,4.771 4.969,4.896 4.969,4.896 5.052,4.896 false 0.073,1.833 1.427,2.063 1.354,0.229 10 false Accelerator Opening 0.073,0.74 1.427,0.969 1.354,0.229 10 false Vehicle Speed 0.083,3.188 1.438,3.417 1.354,0.229 10 false EGR Valve Opening 0.094,4.406 2.188,4.635 2.094,0.229 10 false Mass Air Flow Meter Output 0.094,4.667 1.698,5.188 1.604,0.521 10 false (Changing Value of Intake Air Amount: gm/s) 1.521,2.26 2.094,2.51 0.573,0.25 10 false Closed 1.594,1.583 2.167,1.833 0.573,0.25 10 false Open 1.531,3.563 2.104,3.813 0.573,0.25 10 false Closed 1.573,2.865 2.146,3.115 0.573,0.25 10 false Open 3.521,1.938 5.552,2.146 2.031,0.208 10 false Fully Closed 3.563,0.365 5.594,0.573 2.031,0.208 10 false During Deceleration 5.427,3.448 6.313,3.656 0.885,0.208 10 false Fully Closed 5.406,4.115 6.063,4.354 0.656,0.24 10 false Normal 5.094,4.792 5.75,5.031 0.656,0.24 10 false Abnormal 6.458,5.156 6.875,5.448 0.417,0.292 10 false Time 0.219,0.073 1.542,0.323 1.323,0.25 10 false Flow Malfunction:

WIRING DIAGRAM

A255065
2.156,2.104 2.635,2.281 0.479,0.177 10 false MAIN 5.927,3.146 6.375,3.323 0.448,0.177 10 false MREL 5.917,1.375 6.302,1.531 0.385,0.156 10 false EGR 6.208,4.083 6.615,4.25 0.406,0.167 10 false ECM 5.927,3.573 6.177,3.74 0.25,0.167 10 false E1 4.167,1.865 5.448,2.052 1.281,0.188 10 false E-VRV (for E-EGR) 1.927,3.521 3.698,3.865 1.771,0.344 10 false No. 1 Integration Relay 1.417,1.542 1.698,1.708 0.281,0.167 10 false EFI 0.188,2.396 1.073,2.74 0.885,0.344 10 false from BATT/PI Fuse 5.563,3.146 5.854,3.323 0.292,0.177 10 false G39 5.563,1.396 5.833,1.573 0.271,0.177 10 false C23 5.563,2.323 5.833,2.5 0.271,0.177 10 false C23 5.563,3.594 5.833,3.771 0.271,0.177 10 false C23 5.656,2.938 5.802,3.115 0.146,0.177 10 false 8 5.656,1.177 5.927,1.396 0.271,0.219 10 false 9 5.646,3.385 5.813,3.552 0.167,0.167 10 false 7 3.135,3.146 3.354,3.365 0.219,0.219 10 false 1J 1.5,3.5 1.75,3.667 0.25,0.167 10 false 1J 3.146,1.396 3.375,1.573 0.229,0.177 10 false 1J 3.198,2.938 3.313,3.104 0.115,0.167 10 false 2 3.198,1.188 3.344,1.375 0.146,0.188 10 false 5 4.167,1.688 4.406,1.865 0.24,0.177 10 false C8 0.854,1.396 1.125,1.615 0.271,0.219 10 false 1H 0.906,1.177 1.01,1.354 0.104,0.177 10 false 1 4.813,2.208 4.958,2.385 0.146,0.177 10 false 2 1.594,1.25 1.74,1.427 0.146,0.177 10 false 2 1.271,3.5 1.417,3.677 0.146,0.177 10 false 3 4.052,2.208 4.177,2.427 0.125,0.219 10 false 1 1.333,1.25 1.458,1.469 0.125,0.219 10 false 1 4.813,1.292 4.958,1.469 0.146,0.177 10 false 2 4.042,1.281 4.167,1.5 0.125,0.219 10 false 1 4.052,2.771 5.26,2.958 1.208,0.188 10 false VSV (for EGR Cut) 4.052,2.604 4.354,2.823 0.302,0.219 10 false C10 5.917,2.313 6.375,2.479 0.458,0.167 10 false EGRC 5.604,2.104 5.823,2.281 0.219,0.177 10 false 18

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedures.



HINT:

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0400)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

d.

Read the DTCs.

Result:
Result Proceed to
P0400 is output A
P0400 and other DTCs are output B




A

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE EGR VALVE CLOSE)

B

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE EGR VALVE CLOSE)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine and warm it up, and make sure the A/C switch and all accessory switches are off.


c.

Turn the ignition switch off. Wait for 30 seconds, and then restart the engine.


d.

Turn the tester on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / MAF.

Powertrain > Engine > Data List
Tester Display
MAF
50003 61 319

f.

Read the MAF value displayed on the tester while the engine is idling.


g.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the EGR Valve Close.

Powertrain > Engine > Active Test
Tester Display
Activate the EGR Valve Close
50004 61 183

h.

Read the MAF value when the EGR valve is closed using the Active Test function.

HINT:
·

If idling continues for 15 minutes or more, the EGR valve target opening angle becomes 0% (EGR valve fully closed). As this makes diagnosis impossible, it becomes necessary to drive the vehicle or to restart the engine.

·

Before performing the diagnosis, confirm that the EGR valve target opening angle is not 0%.



Result:
Active Test Result Proceed to
Activate the EGR Valve Close:
Off (Open) to on (Closed)
MAF value does not change A
MAF value changes B


NOTICE:

As the values shown below may differ due to factors such as differences in measuring environments and changes in vehicle condition due to aging, do not use these values to determine whether the vehicle is malfunctioning or not.


HINT:

The problem may be a temporary one, due to the entry of deposits or foreign matter. Check that there are no deposits or foreign matter in the electric vacuum regulating valve assembly or mass air flow meter.


Reference:
EGR Valve Condition (Opening) Measuring Condition MAF (Reference)
Open (55%)
·

Atmosphere pressure: 101 kPa

·

Intake air temperature: 30°C (86°F)

·

Engine coolant temperature: 88°C (190°F)


3.0 to 9.0 gm/s
Close (0%) 15 to 22 gm/s




A

3.CHECK VACUUM HOSES

B

6.INSPECT ELECTRIC EGR CONTROL VALVE ASSEMBLY (EGR VALVE OPERATION)
3.CHECK VACUUM HOSES
a.

Check the vacuum hoses.

OK:

The hoses are not damaged and are securely connected



Result:
Proceed to
OK
NG



OK

4.INSPECT ELECTRIC VACUUM REGULATING VALVE ASSEMBLY

NG

8.REPAIR OR REPLACE VACUUM HOSE
4.INSPECT ELECTRIC VACUUM REGULATING VALVE ASSEMBLY
a.

Inspect the electric vacuum regulating valve assembly

Click hereEngine / Hybrid System>1KD-FTV EMISSION CONTROL>VACUUM REGULATING VALVE>INSPECTION

HINT:

Before replacing the electric vacuum regulating valve assembly, perform a wire harness inspection and if there are any problems with the wire harness, repair or replace it.



Result:
Proceed to
OK
NG



OK

5.INSPECT VACUUM SWITCHING VALVE (FOR EGR CUT)

NG

9.REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY
5.INSPECT VACUUM SWITCHING VALVE (FOR EGR CUT)
a.

Inspect the vacuum switching valve (for EGR cut).

Click hereEngine / Hybrid System>1KD-FTV EMISSION CONTROL>VACUUM SWITCHING VALVE(w/o Glow Plug Controller)>ON-VEHICLE INSPECTION

HINT:

Before replacing the vacuum switching valve (for EGR cut), perform a wire harness inspection and if there are any problems with the wire harness, repair or replace it.



Result:
Proceed to
OK
NG



OK

6.INSPECT ELECTRIC EGR CONTROL VALVE ASSEMBLY (EGR VALVE OPERATION)

NG

10.REPLACE VACUUM SWITCHING VALVE ASSEMBLY (FOR EGR CUT)
6.INSPECT ELECTRIC EGR CONTROL VALVE ASSEMBLY (EGR VALVE OPERATION)
a.

Inspect the electric EGR control valve assembly.

Click hereEngine / Hybrid System>1KD-FTV EMISSION CONTROL>EGR VALVE(w/o Glow Plug Controller)>INSPECTION

OK:

The valve is not stuck and does not have heavy carbon deposits



Result:
Proceed to
OK
NG



OK

7.CHECK FOR DEPOSIT (EGR PASSAGE)

NG

9.REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY
7.CHECK FOR DEPOSIT (EGR PASSAGE)
a.

Check for blockage in the EGR gas passage between the exhaust manifold and electric EGR control valve assembly.

OK:

No blockage in the EGR gas passage



Result:
Proceed to
OK
NG



OK

12.CHECK WHETHER DTC OUTPUT RECURS (DTC P0400)

NG

11.REPAIR OR REPLACE MALFUNCTIONING PARTS
8.REPAIR OR REPLACE VACUUM HOSE
a.

Repair or replace the vacuum hose.


Result:
Proceed to
NEXT



NEXT

12.CHECK WHETHER DTC OUTPUT RECURS (DTC P0400)
9.REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY
a.

Result:
Proceed to
NEXT



NEXT

12.CHECK WHETHER DTC OUTPUT RECURS (DTC P0400)
10.REPLACE VACUUM SWITCHING VALVE ASSEMBLY (FOR EGR CUT)
a.

Result:
Proceed to
NEXT



NEXT

12.CHECK WHETHER DTC OUTPUT RECURS (DTC P0400)
11.REPAIR OR REPLACE MALFUNCTIONING PARTS
Result:
Proceed to
NEXT



NEXT

12.CHECK WHETHER DTC OUTPUT RECURS (DTC P0400)
12.CHECK WHETHER DTC OUTPUT RECURS (DTC P0400)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

d.

Turn the ignition switch off for 30 seconds or more.


e.

Start the engine and warm it up.


f.

Move the shift lever to 2nd gear and decelerate from a speed of 80 km/h (50 mph) or more (fully release the accelerator for approximately 5 seconds or more).


g.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

h.

Read the DTCs.

HINT:

When a DTC is output, the mass air flow meter may be malfunctioning.



Result:
Proceed to
NEXT



NEXT

END