There may be a short circuit between the CAN bus lines and +B when the resistance between terminals 6 (CANH) and 16 (BAT) or terminals 14 (CANL) and 16 (BAT) of the DLC3 is below 6 kΩ.
| Symptom | Trouble Area |
|---|---|
| The resistance between terminals 6 (CANH) and 16 (BAT) or terminals 14 (CANL) and 16 (BAT) of the DLC3 is below 6 kΩ. | ·
Short between CAN bus lines and +B ·
ECM ·
Brake actuator assembly (skid control ECU) ·
Yaw rate sensor assembly ·
Spiral cable sub-assembly (steering angle sensor) ·
No. 1 junction connector ·
No. 2 junction connector ·
No. 3 junction connector |
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of DLC3 |
Disconnect the G57 No. 3 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G18-6 (CANH) - G18-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| G18-14 (CANL) - G18-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the G57 No. 3 junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of DLC3 |
Disconnect the G87 No. 1 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G18-6 (CANH) - G18-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| G18-14 (CANL) - G18-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Rear view of wire harness connector
(to No. 1 Junction Connector) |
| *b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G87-13 (CANH) - G18-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| G87-7 (CANL) - G18-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Rear view of wire harness connector
(to No. 1 Junction Connector) |
| *b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G87-12 (CANH) - G18-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| G87-6 (CANL) - G18-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the G87 No. 1 junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the G38*1 or G156*2 ECM connector.
*1: for 1KD-FTV
*2: for 1KD-FTV (w/ i-ART)
| *A | for 1KD-FTV | *B | for 1KD-FTV (w/ i-ART) |
| *a | Front view of wire harness connector
(to ECM) |
*b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G38-24 (CANH) - G18-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| G38-23 (CANL) - G18-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G156-35 (CANH) - G18-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| G156-36 (CANL) - G18-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the G87 No. 1 junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU]) |
| *b | Front view of DLC3 |
Disconnect the A36 brake actuator assembly (skid control ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A36-25 (CANH) - G18-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| A36-14 (CANL) - G18-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the G87 No. 1 junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Rear view of wire harness connector
(to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
Disconnect the G86 No. 2 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G86-5 (CANH) - G18-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| G86-16 (CANL) - G18-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G18-6 (CANH) - G18-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| G18-14 (CANL) - G18-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Rear view of wire harness connector
(to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G86-7 (CANH) - G18-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| G86-18 (CANL) - G18-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the G86 No. 2 junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of wire harness connector
(to Yaw Rate Sensor Assembly) |
| *b | Front view of DLC3 |
Disconnect the K21 yaw rate sensor assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| K21-3 (CANH) - G18-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| K21-2 (CANL) - G18-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>YAW RATE AND ACCELERATION SENSOR(w/ VSC)>REMOVAL
NG
Reconnect the G86 No. 2 junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Rear view of wire harness connector
(to No. 3 Junction Connector) |
| *b | Front view of DLC3 |
Disconnect the G58 No. 3 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G58-2 (CANH) - G18-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| G58-1 (CANL) - G18-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Rear view of wire harness connector
(to No. 3 Junction Connector) |
| *b | Front view of DLC3 |
Disconnect the G85 No. 3 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G85-2 (CANH) - G18-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| G85-1 (CANL) - G18-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the G58 and G85 No. 3 junction connectors.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Rear view of wire harness connector
(to Spiral Cable Sub-assembly [Steering Angle Sensor]) |
| *b | Front view of DLC3 |
Disconnect the G83 spiral cable sub-assembly (steering angle sensor) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G83-4 (CANH) - G18-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| G83-3 (CANL) - G18-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG