Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(w/ VSC) › 2012.10–2014.10
RM1840EF _57 Power Source / Network _009639 NETWORKING _0052677 CAN COMMUNICATION SYSTEM(w/ VSC) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ VSC)  Open in One Side of CAN Branch Line  


DESCRIPTION

If 2 or more ECUs and/or sensors do not appear on the intelligent tester "Bus Check" screen, one side of the CAN branch wire may be open (one side of the CANH [CAN branch wire]/CANL [CAN branch wire] of the ECU and/or sensor is open).

Symptom Trouble Area
2 or more ECUs and/or sensors do not appear on the intelligent tester "Bus Check" screen.
·

Brake actuator assembly (skid control ECU)

·

Yaw rate sensor assembly

·

Spiral cable sub-assembly (steering angle sensor)

·

CAN branch wire or connector



WIRING DIAGRAM

C272118
6.385,1.385 6.771,1.583 0.385,0.198 10 false ECM 6.125,0.438 6.552,0.615 0.427,0.177 10 false CANH 6.125,1.125 6.542,1.292 0.417,0.167 10 false CANL 0.188,1.521 1.76,2.063 1.573,0.542 10 false Brake Actautor Assembly (Skid Control ECU) 0.771,0.563 1.219,0.854 0.448,0.292 10 false CANH 0.792,1.031 1.188,1.313 0.396,0.281 10 false CANL 1.323,0.927 1.531,1.083 0.208,0.156 10 false 14 1.323,0.469 1.542,0.615 0.219,0.146 10 false 25 0.188,1.354 0.458,1.521 0.271,0.167 10 false A36 0.323,8.031 1.979,8.552 1.656,0.521 10 false Spiral Cable Sub-assembly (Steering Angle Sensor) 0.792,7.094 1.208,7.302 0.417,0.208 10 false CANH 0.823,7.521 1.25,7.74 0.427,0.219 10 false CANL 1.323,7.396 1.521,7.583 0.198,0.188 10 false 3 1.323,6.948 1.51,7.115 0.188,0.167 10 false 4 0.323,7.844 0.615,8.021 0.292,0.177 10 false G83 4.042,0.438 4.229,0.615 0.188,0.177 10 false 12 4.042,0.896 4.156,1.083 0.115,0.188 10 false 6 3.135,0.458 3.323,0.615 0.188,0.156 10 false 13 3.208,0.906 3.333,1.083 0.125,0.177 10 false 7 3.219,1.5 3.365,1.667 0.146,0.167 10 false 4 3.208,1.948 3.344,2.135 0.135,0.188 10 false 1 3.031,2.385 3.333,2.563 0.302,0.177 10 false G87 3.031,2.552 4.646,2.802 1.615,0.25 10 false No. 1 Junction Connector 4.021,2.99 4.156,3.167 0.135,0.177 10 false 7 4.021,3.458 4.188,3.635 0.167,0.177 10 false 18 5.948,2.99 6.052,3.167 0.104,0.177 10 false 3 5.948,3.448 6.052,3.635 0.104,0.188 10 false 2 3.208,2.99 3.323,3.167 0.115,0.177 10 false 5 3.135,3.458 3.302,3.635 0.167,0.177 10 false 16 3.219,4.01 3.333,4.198 0.115,0.188 10 false 6 3.135,4.479 3.333,4.667 0.198,0.188 10 false 17 3.031,4.917 3.344,5.094 0.313,0.177 10 false G86 3.031,5.094 4.667,5.354 1.635,0.26 10 false No. 2 Junction Connector 3.031,8.271 4.625,8.604 1.594,0.333 10 false No. 3 Junction Connector 3.01,5.802 3.354,5.969 0.344,0.167 10 false G58 3.104,5.573 3.302,5.75 0.198,0.177 10 false 2 3.01,6.271 3.333,6.438 0.323,0.167 10 false G58 3.104,6.052 3.271,6.229 0.167,0.177 10 false 1 3.01,7.052 3.333,7.219 0.323,0.167 10 false G85 3.104,6.844 3.26,7 0.156,0.156 10 false 2 3.01,7.51 3.344,7.688 0.333,0.177 10 false G85 3.104,7.323 3.26,7.51 0.156,0.188 10 false 1 4.073,5.802 4.396,5.969 0.323,0.167 10 false G57 4.167,5.573 4.354,5.76 0.188,0.188 10 false 2 4.073,6.281 4.406,6.458 0.333,0.177 10 false G57 4.167,6.063 4.344,6.229 0.177,0.167 10 false 1 6.125,5.813 6.74,6.125 0.615,0.313 10 false CANH 6.125,6.281 6.729,6.521 0.604,0.24 10 false CANL 6.385,6.656 6.865,6.844 0.479,0.188 10 false G18 6.385,6.802 6.99,7.094 0.604,0.292 10 false DLC3 5.948,5.677 6.156,5.875 0.208,0.198 10 false 6 5.875,6.156 6.073,6.344 0.198,0.188 10 false 14 6.125,3.094 6.677,3.365 0.552,0.271 10 false CANH 6.135,3.542 6.604,3.729 0.469,0.188 10 false CANL 6.031,4.073 7.115,4.573 1.083,0.5 10 false Yaw Rate Sensor Assembly 6.031,3.927 6.406,4.125 0.375,0.198 10 false K21 5.323,0.792 5.667,0.948 0.344,0.156 10 false 23*1 5.323,0.323 5.635,0.49 0.313,0.167 10 false 24*1 5.323,1.01 5.625,1.219 0.302,0.208 10 false G38 5.323,0.542 5.615,0.729 0.292,0.188 10 false G38 5.708,0.792 6.021,0.958 0.313,0.167 10 false 36*2 5.708,0.323 6.073,0.49 0.365,0.167 10 false 35*2 5.688,1.01 6.063,1.219 0.375,0.208 10 false G156 5.688,0.542 6.052,0.74 0.365,0.198 10 false G156 5.198,8.073 6.865,8.302 1.667,0.229 10 false *1: for 1KD-FTV 5.198,8.344 6.938,8.667 1.74,0.323 10 false *2: for 1KD-FTV (w/ i-ART)

CAUTION / NOTICE / HINT

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:
·

Perform the following inspection for the ECUs (sensors) which are displayed on the intelligent tester. If a malfunction cannot be identified, perform the following inspections for the ECUs (sensors) connected to the CAN communication system.

·

Do not remove the ECM and No. 3 junction connector as they are the end parts of the circuit. If removed, CAN communication will not be possible.

·

The open circuit confirmation of the ECM, No. 3 junction connector and CAN main wire is performed in the Check CAN Bus Line procedure of "How to Proceed with Troubleshooting". This inspection only has procedures for checking for an open circuit on one side of a CAN branch wire.



PROCEDURE

1.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (SKID CONTROL ECU)
a.

Disconnect the A36 brake actuator assembly (skid control ECU) connector.


b.

Select "Bus Check" on the intelligent tester.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(w/ VSC)>DIAGNOSIS SYSTEM

Result:
Result Proceed to
"Skid Control (ABS/VSC/TRAC)" is not displayed on the intelligent tester A
Several ECUs and sensors in addition to "Skid Control (ABS/VSC/TRAC)" are displayed on the intelligent tester B




A

2.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (SKID CONTROL ECU CAN BRANCH WIRE)

B

3.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (YAW RATE SENSOR ASSEMBLY)
2.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (SKID CONTROL ECU CAN BRANCH WIRE)
a.
C234968C41
0.125,1.01 0.677,1.344 0.552,0.333 1.875,1.969 1.792,1.969 1.792,1.969 1.49,1.292 true 1.469,1.365 1.208,1.938 1.208,1.938 1.104,1.938 true 0.281,1.094 0.552,1.26 0.271,0.167 10 false A36 1.906,1.885 2.313,2.031 0.406,0.146 10 false CANL 0.708,1.854 1.115,2 0.406,0.146 10 false CANH 0.073,0.052 0.333,0.198 0.26,0.146 10 false *a
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])


Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A36-25 (CANH) - A36-14 (CANL) Ignition switch off 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (SKID CONTROL ECU)

3.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (YAW RATE SENSOR ASSEMBLY)
a.

Disconnect the K21 yaw rate sensor assembly connector.


b.

Select "Bus Check" on the intelligent tester.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(w/ VSC)>DIAGNOSIS SYSTEM

Result:
Result Proceed to
"Yaw Rate Sensor" is not displayed on the intelligent tester A
Several ECUs and sensors in addition to "Yaw Rate Sensor" are displayed on the intelligent tester B




A

4.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (YAW RATE SENSOR ASSEMBLY CAN BRANCH WIRE)

B

5.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (STEERING ANGLE SENSOR CAN BRANCH WIRE)
4.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (YAW RATE SENSOR ASSEMBLY CAN BRANCH WIRE)
a.
C222816C04
1.458,0.354 2.031,0.677 0.573,0.323 1.625,1.406 1.823,1.906 1.823,1.906 1.948,1.906 true 1.469,1.406 1.292,1.906 1.292,1.906 1.167,1.906 true 0.115,0.115 0.333,0.302 0.219,0.188 10 false *a 1.635,0.438 2.073,0.719 0.438,0.281 10 false K21 1.99,1.823 2.531,2.073 0.542,0.25 10 false CANH 0.792,1.823 1.198,2.021 0.406,0.198 10 false CANL
*a Front view of wire harness connector
(to Yaw Rate Sensor Assembly)


Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
K21-3 (CANH) - K21-2 (CANL) Ignition switch off 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (YAW RATE SENSOR ASSEMBLY)

5.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (STEERING ANGLE SENSOR CAN BRANCH WIRE)
a.
C234977C04
0.438,1 0.917,1.313 0.479,0.313 1.781,1.323 2.146,1.792 2.146,1.792 2.26,1.792 true 1.677,1.323 1.323,1.792 1.323,1.792 1.219,1.792 true 0.552,1.083 0.906,1.25 0.354,0.167 10 false G83 0.813,1.708 1.25,1.938 0.438,0.229 10 false CANH 2.292,1.708 2.677,1.896 0.385,0.188 10 false CANL 0.073,0.042 0.375,0.208 0.302,0.167 10 false *a
*a Rear view of wire harness connector
(to Spiral Cable Sub-assembly [Steering Angle Sensor])


Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

Disconnect the G83 spiral cable sub-assembly (steering angle sensor) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G83-4 (CANH) - G83-3 (CANL) Ignition switch off 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

REPLACE SPIRAL CABLE SUB-ASSEMBLY (STEERING ANGLE SENSOR)

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (STEERING ANGLE SENSOR)