Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM(for DPF) › from 2012.10
RM1840EF _51 Engine / Hybrid System _009570 1KD-FTV ENGINE CONTROL _0052104 ECD SYSTEM(for DPF) C

1KD-FTV ENGINE CONTROL  ECD SYSTEM(for DPF)  P0201  Injector Circuit / Open - (Cylinder 1)  P0202  Injector Circuit / Open - (Cylinder 2)  P0203  Injector Circuit / Open - (Cylinder 3)  P0204  Injector Circuit / Open - (Cylinder 4)  P062D  No. 1 Fuel Injector Driver Circuit Performance  


DESCRIPTION

The injector driver (EDU) delivers drive signals to injector assembly using the DC/DC converter, which provides a high-voltage and quick-charging system.

Soon after the injector driver (EDU) receives a injection command (#1 to #4) signal from the ECM, the injector driver (EDU) responds to the command with an injector injection confirmation (INJF) signal when the current is applied to the injector assembly.

A210270
1.135,5.646 1.552,5.885 0.417,0.24 2.594,5.677 3.031,5.938 0.438,0.26 4.229,5.875 4.635,6.125 0.406,0.25 5.667,6 6.063,6.25 0.396,0.25 3.406,0.146 3.76,0.375 0.354,0.229 10 false EDU 2.563,1.469 3.167,1.885 0.604,0.417 10 false DC/DC Converter 0.313,1.438 1.219,1.76 0.906,0.323 10 false from Battery 0.313,2.208 1.365,2.448 1.052,0.24 10 false Command Pulse 0.854,5.188 2.104,5.448 1.25,0.26 10 false Confirmation Pulse 0.063,5.625 1.156,5.854 1.094,0.229 10 false (EDU) Connector 0.281,0.094 1.708,0.375 1.427,0.281 10 false EDU Wiring Diagram 0.656,3.625 1.031,3.885 0.375,0.26 10 false ECM 1.552,2.521 1.854,2.719 0.302,0.198 10 false #1 1.552,2.813 1.865,3.021 0.313,0.208 10 false #4 1.552,3.125 1.823,3.292 0.271,0.167 10 false #2 1.563,3.427 1.833,3.594 0.271,0.167 10 false #3 1.51,4.042 1.896,4.219 0.385,0.177 10 false INJF 1.5,4.635 1.885,4.823 0.385,0.188 10 false IJEN 1.5,3.729 1.823,3.896 0.323,0.167 10 false PRD 1.51,4.333 1.833,4.5 0.323,0.167 10 false RLF 5,2.49 5.354,2.656 0.354,0.167 10 false IJ1- 5,0.604 5.427,0.823 0.427,0.219 10 false RLF+ 5,0.917 5.396,1.083 0.396,0.167 10 false IJ3+ 5,1.25 5.396,1.417 0.396,0.167 10 false IJ2+ 5,1.573 5.396,1.74 0.396,0.167 10 false IJ4+ 5,1.885 5.396,2.052 0.396,0.167 10 false IJ1+ 5,2.813 5.354,2.979 0.354,0.167 10 false IJ4- 5,3.115 5.354,3.281 0.354,0.167 10 false IJ2- 5,3.438 5.354,3.604 0.354,0.167 10 false IJ3- 5,3.76 5.385,3.927 0.385,0.167 10 false RLF- 3.229,3.25 3.688,3.646 0.458,0.396 10 false Control Circuit 3.563,5.417 3.948,5.615 0.385,0.198 10 false GND 1.813,7.104 5.271,7.583 3.458,0.479 10 false CAUTION: Terminals K, L, M, N, O, P, Q, R, S and T are high voltage terminals. 1.188,5.677 1.708,5.948 0.521,0.271 10 false C107 2.656,5.719 3.042,5.917 0.385,0.198 10 false C108 4.281,5.927 4.792,6.208 0.51,0.281 10 false C109 5.708,6.042 6.219,6.302 0.51,0.26 10 false C110 0.083,5.448 1.177,5.656 1.094,0.208 10 false Injector Driver

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0201 Injector Circuit / Open - (Cylinder 1) Open or short in injector circuit occurs a certain number of times (a maximum of approx. 0.5 seconds).
(1 trip detection logic)
·

Open or short in injector driver circuit

·

Injector assembly

·

Injector driver

·

ECM


Comes on DTC stored
P0202 Injector Circuit / Open - (Cylinder 2) Open or short in injector circuit occurs a certain number of times (a maximum of approx. 0.5 seconds).
(1 trip detection logic)
·

Open or short in injector driver circuit

·

Injector assembly

·

Injector driver

·

ECM


Comes on DTC stored
P0203 Injector Circuit / Open - (Cylinder 3) Open or short in injector circuit occurs a certain number of times (a maximum of approx. 0.5 seconds).
(1 trip detection logic)
·

Open or short in injector driver circuit

·

Injector assembly

·

Injector driver

·

ECM


Comes on DTC stored
P0204 Injector Circuit / Open - (Cylinder 4) Open or short in injector circuit occurs a certain number of times (a maximum of approx. 0.5 seconds).
(1 trip detection logic)
·

Open or short in injector driver circuit

·

Injector assembly

·

Injector driver

·

ECM


Comes on DTC stored
P062D No. 1 Fuel Injector Driver Circuit Performance Inconsistency in the injection waveforms between the injector driver and ECM while the engine is running a certain number of times (a maximum of approx. 0.5 seconds).
(1 trip detection logic)
·

Open or short in injector driver circuit

·

Injector assembly

·

Injector driver

·

ECM


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

P0201, P0202, P0203, P0204
DTC Detection Drive Pattern Idling for 5 seconds

P062D
DTC Detection Drive Pattern Idling for 5 seconds

MONITOR DESCRIPTION

P0201, P0202, P0203, P0204:

The ECM compares injection command (# 1 to # 4) signals and injection confirmation (INJF) signals for each cylinder. If the ECM determines that a cylinder has a malfunction, DTC P0201, P0202, P0203 or P0204 will be stored.


P062D:

The ECM continuously monitors both injection command (#1 to #4) signals and injection confirmation (INJF) signals. This DTC will be stored if the ECM determines that the number of #1 to #4 signals and INJF signals are inconsistent.

The injector assembly are grounded over a Field Effect Transistor (FET) and a serial resistor. This resistor creates a voltage drop, which is monitored by the injector driver (EDU) (injector drive circuit) in relation to the current drawn by the injector assembly. When the injector current becomes too high, the voltage drop over the resistor exceeds a specified level and no INJF signal for that cylinder is sent to the ECM.

After the engine is started, when there is no injection confirmation (INJF) signal from the injector driver (EDU) to the ECM even though the ECM sends injection command (#1 to #4) signals to the injector driver (EDU), DTC P062D is stored.

If this DTC is stored, the ECM enters fail-safe mode and limits engine power or stops the engine. The fail-safe mode continues until the ignition switch is turned off.

A145849
4.948,2.521 4.615,2.875 false 4.677,3.25 4.885,3.583 false 0.125,0.063 1.708,0.271 1.583,0.208 10 false Malfunction Detection: 2.615,0.688 3.021,0.885 0.406,0.198 10 false ECM 0.063,1.76 1.74,2.052 1.677,0.292 10 false Injection Command Signal 0.063,3.031 2.021,3.24 1.958,0.208 10 false Injection Confirmation Signal 1.833,2.031 2.448,2.25 0.615,0.219 10 false #1 to #4 2.073,2.792 2.49,3.031 0.417,0.24 10 false INJF 3.323,1.792 3.604,1.99 0.281,0.198 10 false ON 3.604,0.469 5.417,0.708 1.813,0.24 10 false Command Signal (#1 to #4) 3.604,1.188 5.333,1.438 1.729,0.25 10 false Confirmation Signal (INJF) 5.875,0.677 6.26,0.875 0.385,0.198 10 false EDU 3.698,2.135 4.063,2.333 0.365,0.198 10 false OFF 5,2.438 5.771,2.635 0.771,0.198 10 false Abnormal 4.938,3.5 5.521,3.698 0.583,0.198 10 false Normal


WIRING DIAGRAM

A276467
0.625,0.802 0.969,0.969 0.344,0.167 10 false INJF 1.021,0.802 1.458,0.958 0.438,0.156 10 false C109 1.021,1.24 1.458,1.396 0.438,0.156 10 false C109 1.021,1.698 1.458,1.854 0.438,0.156 10 false C109 1.01,2.115 1.448,2.271 0.438,0.156 10 false C109 1.01,2.563 1.448,2.719 0.438,0.156 10 false C109 1.021,3.063 1.417,3.219 0.396,0.156 10 false C108 1.021,3.979 1.417,4.135 0.396,0.156 10 false C108 1.115,0.615 1.229,0.771 0.115,0.156 10 false 8 0.688,1.24 0.979,1.406 0.292,0.167 10 false #10 1.115,1.052 1.229,1.208 0.115,0.156 10 false 7 0.667,2.552 0.958,2.719 0.292,0.167 10 false #40 1.115,1.5 1.229,1.656 0.115,0.156 10 false 3 0.667,1.698 0.958,1.865 0.292,0.167 10 false #20 1.115,1.927 1.229,2.083 0.115,0.156 10 false 6 0.667,2.125 0.958,2.292 0.292,0.167 10 false #30 6.198,0.802 6.625,1.052 0.427,0.25 10 false INJF 6.198,1.219 6.49,1.385 0.292,0.167 10 false #1 6.208,2.542 6.5,2.708 0.292,0.167 10 false #4 6.198,2.115 6.49,2.281 0.292,0.167 10 false #3 6.198,1.688 6.49,1.854 0.292,0.167 10 false #2 5.792,0.802 6.198,0.958 0.406,0.156 10 false C113 5.896,0.625 6.083,0.781 0.188,0.156 10 false 20 5.792,1.24 6.198,1.396 0.406,0.156 10 false C113 5.896,1.063 6.094,1.219 0.198,0.156 10 false 21 5.792,1.688 6.198,1.844 0.406,0.156 10 false C113 5.906,1.51 6.125,1.667 0.219,0.156 10 false 22 5.792,2.115 6.198,2.271 0.406,0.156 10 false C113 5.906,1.938 6.125,2.094 0.219,0.156 10 false 23 5.792,2.552 6.198,2.708 0.406,0.156 10 false C113 5.906,2.375 6.104,2.531 0.198,0.156 10 false 24 1.115,2.375 1.229,2.531 0.115,0.156 10 false 4 0.667,3.052 0.969,3.219 0.302,0.167 10 false IJ1+ 1.115,2.875 1.229,3.031 0.115,0.156 10 false 1 4.26,3.146 4.375,3.302 0.115,0.156 10 false 2 3.594,3.156 3.708,3.313 0.115,0.156 10 false 1 1.115,4.219 1.229,4.375 0.115,0.156 10 false 3 1.104,6.615 1.219,6.771 0.115,0.156 10 false 3 1.115,5.708 1.229,5.865 0.115,0.156 10 false 1 1.115,3.802 1.229,3.958 0.115,0.156 10 false 4 1.115,5.135 1.229,5.292 0.115,0.156 10 false 6 3.438,3.365 3.813,3.542 0.375,0.177 10 false C103 3.438,3.51 5.094,3.802 1.656,0.292 10 false No. 1 Injector Assembly 3.438,4.688 3.896,4.865 0.458,0.177 10 false C104 3.438,7.719 5.135,8.052 1.698,0.333 10 false No. 4 Injector Assembly 3.438,6.177 3.854,6.354 0.417,0.177 10 false C105 3.406,4.844 5.042,5.156 1.635,0.313 10 false No. 2 Injector Assembly 3.438,7.552 3.865,7.729 0.427,0.177 10 false C106 3.448,6.333 5.125,6.635 1.677,0.302 10 false No. 3 Injector Assembly 4.292,4.479 4.406,4.635 0.115,0.156 10 false 2 3.604,4.49 3.719,4.646 0.115,0.156 10 false 1 4.271,5.979 4.385,6.135 0.115,0.156 10 false 2 3.583,5.99 3.698,6.146 0.115,0.156 10 false 1 4.271,7.323 4.385,7.479 0.115,0.156 10 false 2 3.604,7.323 3.719,7.479 0.115,0.156 10 false 1 0.667,3.969 0.938,4.135 0.271,0.167 10 false IJ1- 1.021,4.396 1.417,4.552 0.396,0.156 10 false C108 1.021,5.313 1.417,5.469 0.396,0.156 10 false C108 1.021,5.885 1.438,6.042 0.417,0.156 10 false C107 0.656,4.417 0.958,4.583 0.302,0.167 10 false IJ2+ 0.656,5.313 0.927,5.479 0.271,0.167 10 false IJ2- 0.656,5.885 0.958,6.052 0.302,0.167 10 false IJ3+ 0.667,6.781 0.938,6.948 0.271,0.167 10 false IJ3- 1.021,7.229 1.417,7.385 0.396,0.156 10 false C108 1.021,8.156 1.417,8.313 0.396,0.156 10 false C108 1.021,6.813 1.438,6.969 0.417,0.156 10 false C107 1.115,7.042 1.24,7.198 0.125,0.156 10 false 2 1.094,7.958 1.208,8.115 0.115,0.156 10 false 5 0.646,7.229 0.948,7.396 0.302,0.167 10 false IJ4+ 0.667,8.135 0.938,8.302 0.271,0.167 10 false IJ4- 6.344,0.208 6.74,0.438 0.396,0.229 10 false ECM 0.385,0.167 0.781,0.354 0.396,0.188 10 false EDU

A276468
6.458,5.26 6.813,5.438 0.354,0.177 10 false ECM 4.385,1.656 4.74,1.833 0.354,0.177 10 false EDU 4.385,3.344 4.948,3.531 0.563,0.188 10 false MAIN 0.229,5.26 1.125,5.438 0.896,0.177 10 false Injector Driver 1.479,4.615 2.021,4.802 0.542,0.188 10 false Battery 1.5,3.729 2.115,3.917 0.615,0.188 10 false BATT P/I 2.896,3.771 3.188,3.958 0.292,0.188 10 false EFI 4.052,1.042 4.25,1.219 0.198,0.177 10 false 1J 3.49,1.042 3.688,1.219 0.198,0.177 10 false 1J 3.271,1.042 3.438,1.24 0.167,0.198 10 false 8 4.333,1.042 4.5,1.24 0.167,0.198 10 false 7 5.094,2.458 5.292,2.635 0.198,0.177 10 false 1J 5.083,2.885 5.281,3.063 0.198,0.177 10 false 1J 5.094,3.906 5.292,4.083 0.198,0.177 10 false 1J 4.052,4.135 4.25,4.313 0.198,0.177 10 false 1J 2.354,3.906 2.594,4.083 0.24,0.177 10 false 1H 2.26,4.344 4.01,4.708 1.75,0.365 10 false Integration Relay 0.99,1.542 1.354,1.719 0.365,0.177 10 false C107 0.979,0.563 1.344,0.74 0.365,0.177 10 false C107 5.938,0.552 6.354,0.729 0.417,0.177 10 false G148 5.927,2.875 6.344,3.052 0.417,0.177 10 false G148 5.938,3.906 6.333,4.083 0.396,0.177 10 false G149 5.938,2.458 6.333,2.635 0.396,0.177 10 false G149 5.115,2.271 5.271,2.448 0.156,0.177 10 false 4 5.125,2.708 5.281,2.885 0.156,0.177 10 false 2 5.115,3.729 5.271,3.906 0.156,0.177 10 false 1 6.021,3.74 6.26,3.938 0.24,0.198 10 false 23 6.01,2.698 6.25,2.896 0.24,0.198 10 false 11 6.021,2.281 6.26,2.479 0.24,0.198 10 false 24 6.01,0.385 6.25,0.583 0.24,0.198 10 false 12 1.115,0.396 1.271,0.573 0.156,0.177 10 false 2 2.406,3.729 2.563,3.906 0.156,0.177 10 false 1 4.313,4.135 4.469,4.313 0.156,0.177 10 false 3 1.115,1.365 1.271,1.542 0.156,0.177 10 false 4 6.375,2.438 6.635,2.594 0.26,0.156 10 false +B 0.698,0.573 0.958,0.729 0.26,0.156 10 false +B 0.583,1.542 0.958,1.698 0.375,0.156 10 false GND 6.365,0.542 6.74,0.719 0.375,0.177 10 false IREL 6.375,2.875 6.865,3.063 0.49,0.188 10 false MREL 6.365,3.896 6.823,4.063 0.458,0.167 10 false BATT 5.083,2 5.281,2.177 0.198,0.177 10 false 1J 5.938,2 6.333,2.177 0.396,0.177 10 false G149 5.115,1.823 5.271,2 0.156,0.177 10 false 5 6.021,1.813 6.26,2.01 0.24,0.198 10 false 17 6.375,1.99 6.719,2.146 0.344,0.156 10 false +B2

CAUTION / NOTICE / HINT

CAUTION:

Make sure to perform work on high voltage circuits with the ignition switch off.


NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION).



HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ENGINE CRANKING CONDITION
a.

Check the engine cranking condition.

Result:
Result Proceed to
Engine does not start*1 A
Engine starts, but idling is rough*2 B
Except above C


HINT:
·

*1: Once DTC P062D is cleared, it is not stored again even when the engine does not start due to a malfunction in the injector driver (EDU).

When the engine cannot be started due to a malfunction in the injector driver (EDU), the value for "Fuel Press" is higher than the value for "Target Common Rail Pressure"

·

*2: DTC P0201, P0202, P0203, P0204 and P062D are stored at this time.





A

2.INSPECT ECM

B

7.CHECK WHETHER DTC OUTPUT RECURS

C

2.INSPECT ECM
a.
A303266
1.365,0.333 1.781,0.604 0.417,0.271 2.823,0.302 3.24,0.573 0.417,0.271 1.083,1.698 1.365,1.073 true 1.604,1.677 1.531,1.073 true 1.865,1.698 1.635,1.083 true 1.323,1.708 1.479,1.083 true 3.042,1.688 3.26,0.854 true 0.083,0.052 0.396,0.25 0.313,0.198 10 false *a 1.417,0.385 1.792,0.583 0.375,0.198 10 false C113 2.875,0.365 3.25,0.563 0.375,0.198 10 false C112 0.979,1.729 1.167,1.917 0.188,0.188 10 false #4 1.25,1.729 1.438,1.917 0.188,0.188 10 false #3 1.563,1.729 1.75,1.917 0.188,0.188 10 false #2 1.833,1.729 2.021,1.917 0.188,0.188 10 false #1 2.948,1.74 3.177,1.927 0.229,0.188 10 false E1 2.438,2.219 3.125,2.438 0.688,0.219 10 false 2 V/DIV. 3.01,3.375 3.385,3.573 0.375,0.198 10 false GND 0.396,4.198 1.396,4.427 1,0.229 10 false 1 msec./DIV.
*a Component with harness connected
(ECM)


Check the waveform of the ECM connectors using an oscilloscope.

OK:
Tester Connection Condition Specified Condition
C113-21 (#1) - C112-1 (E1) Cranking Correct waveform is as shown
C113-22 (#2) - C112-1 (E1) Cranking Correct waveform is as shown
C113-23 (#3) - C112-1 (E1) Cranking Correct waveform is as shown
C113-24 (#4) - C112-1 (E1) Cranking Correct waveform is as shown



Result:
Proceed to
OK
NG



OK

3.CHECK TERMINAL VOLTAGE INJECTOR DRIVER POWER SOURCE

NG

6.REPLACE ECM
3.CHECK TERMINAL VOLTAGE INJECTOR DRIVER POWER SOURCE
a.
A204910C05
0.49,1.104 0.906,1.354 0.417,0.25 1.969,0.979 2.438,0.719 true 1.969,1.417 2.406,1.625 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 0.531,1.146 0.927,1.323 0.396,0.177 10 false C107 2.49,0.635 2.802,0.833 0.313,0.198 10 false +B 2.469,1.563 2.927,1.76 0.458,0.198 10 false GND
*a Front view of wire harness connector
(to Injector Driver)


Disconnect the injector driver connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C107-2 (+B) - C107-4 (GND) Ignition switch ON 11 to 14 V



c.

Reconnect the injector driver connectors.


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (INJECTOR DRIVER - ECM)

NG

14.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.CHECK HARNESS AND CONNECTOR (INJECTOR DRIVER - ECM)
a.

Disconnect the injector driver connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C109-7 (#10) - C113-21 (#1) Always Below 1 Ω
C109-3 (#20) - C113-22 (#2) Always Below 1 Ω
C109-6 (#30) - C113-23 (#3) Always Below 1 Ω
C109-4 (#40) - C113-24 (#4) Always Below 1 Ω
C109-8 (INJF) - C113-20 (INJF) Always Below 1 Ω
C109-7 (#10) or C113-21 (#1) - Body ground Always 10 kΩ or higher
C109-3 (#20) or C113-22 (#2) - Body ground Always 10 kΩ or higher
C109-6 (#30) or C113-23 (#3) - Body ground Always 10 kΩ or higher
C109-4 (#40) or C113-24 (#4) - Body ground Always 10 kΩ or higher
C109-8 (INJF) or C113-20 (INJF) - Body ground Always 10 kΩ or higher



d.

Reconnect the injector driver connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

5.REPLACE INJECTOR DRIVER

NG

14.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.REPLACE INJECTOR DRIVER
a.

Replace the injector driver.

Click hereEngine / Hybrid System>1KD-FTV FUEL>INJECTOR DRIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT

15.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

15.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

d.

Turn the ignition switch off for 30 seconds.


e.

Start the engine and idle it for 30 seconds.


f.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

g.

Check the DTCs output on the tester.

HINT:
·

The cylinder with the malfunctioning injector assembly can be determined based on the output DTCs.

·

If the DTC P0201 is output, check the No. 1 injector assembly circuit.

·

If the DTC P0202 is output, check the No. 2 injector assembly circuit.

·

If the DTC P0203 is output, check the No. 3 injector assembly circuit.

·

If the DTC P0204 is output, check the No. 4 injector assembly circuit.




Result:
Proceed to
NEXT



NEXT

8.INSPECT INJECTOR DRIVER
8.INSPECT INJECTOR DRIVER
a.
A301852
0.281,0.698 0.688,0.938 0.406,0.24 0.281,0.99 0.688,1.229 0.406,0.24 0.76,0.698 1.167,0.938 0.406,0.24 0.771,0.99 1.177,1.229 0.406,0.24 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 0.333,0.74 0.729,0.948 0.396,0.208 10 false C103 0.813,0.74 1.208,0.948 0.396,0.208 10 false C104 0.813,1.031 1.208,1.24 0.396,0.208 10 false C106 0.333,1.031 0.729,1.24 0.396,0.208 10 false C105 2.188,2.208 2.938,2.417 0.75,0.208 10 false 50 V/DIV. 3.031,4.021 3.385,4.271 0.354,0.25 10 false GND 0.24,4.219 1.24,4.448 1,0.229 10 false 10 μsec./DIV.
*a Front view of wire harness connector
(to Fuel Injector)


Disconnect the injector assembly connectors for all cylinders.

NOTICE:

If only the injector assembly connector of the malfunctioning cylinder is disconnected, the engine will start and there will be rough idling. Therefore, disconnect all injector assembly connectors before inspecting the waveform.



b.

Start the engine.


c.

Check the waveform of the injector assembly connectors using an oscilloscope.

OK:
Tester Connection Condition Specified Condition
C103-1 - C103-2 Cranking Voltage increases by 50 V or more
C104-1 - C104-2 Cranking Voltage increases by 50 V or more
C105-1 - C105-2 Cranking Voltage increases by 50 V or more
C106-1 - C106-2 Cranking Voltage increases by 50 V or more



Result:
Proceed to
OK
NG



OK

9.REPLACE INJECTOR ASSEMBLY (RELEVANT CYLINDER)

NG

12.CHECK HARNESS AND CONNECTOR (INJECTOR ASSEMBLY - INJECTOR DRIVER)
9.REPLACE INJECTOR ASSEMBLY (RELEVANT CYLINDER)
a.

Replace the injector assembly of the cylinder relevant to the DTC.

Click hereEngine / Hybrid System>1KD-FTV FUEL>FUEL INJECTOR(w/ Glow Plug Controller)>REMOVAL

NOTICE:
·

When replacing the injector assembly for a cylinder, always be sure to use a new injection pipe.

·

Follow the procedure in the repair manual and temporarily install the injection pipes and nozzle leakage pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe may become incomplete, resulting in a fuel leak.




Result:
Proceed to
NEXT



NEXT

10.BLEED AIR FROM FUEL SYSTEM
10.BLEED AIR FROM FUEL SYSTEM

Result:
Proceed to
NEXT



NEXT

11.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
11.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
a.

Register the injector compensation code.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION


b.

Perform the fuel injector pilot quantity learning.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION


Result:
Proceed to
NEXT



NEXT

15.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.CHECK HARNESS AND CONNECTOR (INJECTOR ASSEMBLY - INJECTOR DRIVER)
a.

Disconnect the injector assembly connectors.


b.

Disconnect the injector driver connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C103-1 - C108-1 (IJ1+) Always Below 1 Ω
C103-2 - C108-4 (IJ1-) Always Below 1 Ω
C104-1 - C108-3 (IJ2+) Always Below 1 Ω
C104-2 - C108-6 (IJ2-) Always Below 1 Ω
C105-1 - C107-1 (IJ3+) Always Below 1 Ω
C105-2 - C107-3 (IJ3-) Always Below 1 Ω
C106-1 - C108-2 (IJ4+) Always Below 1 Ω
C106-2 - C108-5 (IJ4-) Always Below 1 Ω
C103-1 or C108-1 (IJ1+) - Body ground Always 10 kΩ or higher
C103-2 or C108-4 (IJ1-) - Body ground Always 10 kΩ or higher
C104-1 or C108-3 (IJ2+) - Body ground Always 10 kΩ or higher
C104-2 or C108-6 (IJ2-) - Body ground Always 10 kΩ or higher
C105-1 or C107-1 (IJ3+) - Body ground Always 10 kΩ or higher
C105-2 or C107-3 (IJ3-) - Body ground Always 10 kΩ or higher
C106-1 or C108-2 (IJ4+) - Body ground Always 10 kΩ or higher
C106-2 or C108-5 (IJ4-) - Body ground Always 10 kΩ or higher



d.

Reconnect the injector assembly connectors.


e.

Reconnect the injector driver connectors.


Result:
Proceed to
OK
NG



OK

13.REPLACE INJECTOR DRIVER

NG

14.REPAIR OR REPLACE HARNESS OR CONNECTOR
13.REPLACE INJECTOR DRIVER
a.

Replace the injector driver.

Click hereEngine / Hybrid System>1KD-FTV FUEL>INJECTOR DRIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT

15.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
14.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

15.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
15.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.


b.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

c.

Turn the ignition switch off for 30 seconds or more.


d.

Start the engine and idle it for 10 seconds.


e.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

f.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END