Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM › from 2012.04
RM1840EF _51 Engine / Hybrid System _009608 CRUISE CONTROL _0052446 CRUISE CONTROL SYSTEM C

CRUISE CONTROL  CRUISE CONTROL SYSTEM  P0571  Stop Light Switch Circuit Malfunction  


DESCRIPTION

When the brake pedal is depressed, the stop light switch sends a signal to the ECM. Upon receiving the signal, the ECM cancels cruise control. Even if there is a malfunction in the stop light signal circuit while cruise control is in operation, normal driving is maintained due to a fail-safe function. When the brake pedal is depressed, positive voltage is applied to terminal STP of the ECM through the STOP fuse and stop light switch, and the ECM cancels cruise control.

DTC No. Detection Item DTC Detection Condition Trouble Area
P0571 Stop Light Switch Circuit Malfunction The voltages of terminals ST1- and STP of the ECM are both below 1 V for 0.5 seconds or more.
·

Stop light switch circuit

·

Stop light switch assembly

·

ECM



WIRING DIAGRAM

E149001
5.205,2.205 5.602,2.398 0.397,0.193 10 ECM 5.205,2.046 6.787,2.221 1.582,0.174 10 G38*1, G157*2 4.698,0.672 5.087,0.851 0.390,0.179 10 15*1 4.782,0.805 5.046,0.984 0.265,0.179 10 8*2 4.698,1.281 5.060,1.460 0.362,0.179 10 14*1 4.782,1.414 5.072,1.593 0.290,0.179 10 9*2 2.666,2.05 4.419,2.257 1.753,0.207 10 Stop Light Switch Assembly 2.666,1.879 2.965,2.063 0.299,0.184 10 A24 3.692,0.797 3.876,0.976 0.184,0.179 10 1 3.692,1.398 3.876,1.577 0.184,0.179 10 4 2.848,0.797 3.031,0.976 0.184,0.179 10 2 2.848,1.398 3.031,1.577 0.184,0.179 10 3 1.991,1.059 2.415,1.229 0.424,0.170 10 STOP 2.062,1.656 2.389,1.826 0.327,0.170 10 IGN 0.75,0.886 1.615,1.075 0.864,0.188 10 from Battery 0.307,1.489 1.646,1.677 1.339,0.188 10 from Ignition Switch 5.169,0.901 5.529,1.085 0.360,0.184 10 STP 5.169,1.505 5.529,1.689 0.360,0.184 10 ST1- 0.135,2.403 0.958,2.568 0.823,0.165 10 *2: for i-ART 0.135,2.129 1.235,2.295 1.100,0.165 10 *1: except i-ART

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH)
a.

Using the intelligent tester, read the Data List.

Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL SYSTEM>DATA LIST / ACTIVE TEST

Cruise Control:
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light SW M-CPU Stop light switch signal (Main CPU) / ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-


OK:

The display is as specified in the normal condition column.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (BATTERY - STOP LIGHT SWITCH)
2.CHECK HARNESS AND CONNECTOR (BATTERY - STOP LIGHT SWITCH)
a.

Disconnect the A24 stop light switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A24-2 - Body ground Always 11 to 14 V
A24-3 - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

3.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.
E171636
0.771,1.771 0.802,1.229 0.802,1.229 0.979,1.229 false 1.031,1.125 1.344,1.281 0.313,0.156 10 *1 0.333,2.594 0.646,2.75 0.313,0.156 10 *a 0.885,2.573 1.198,2.729 0.313,0.156 10 *b
*1 Pin
*a Not pushed
*b Pushed


Remove the stop light switch.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - 2 Pin pushed 10 kΩ or higher
Pin not pushed Below 1 Ω
3 - 4 Pin pushed Below 1 Ω
Pin not pushed 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - ECM)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - ECM)

*1: except i-ART

*2: for i-ART


a.

Disconnect the A24 stop light switch connector.


b.

Disconnect the G38*1 or G157*2 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
except i-ART
Tester Connection Condition Specified Condition
A24-1 - G38-15 (STP) Always Below 1 Ω
A24-4 - G38-14 (ST1-)
A24-1 - Body ground Always 10 kΩ or higher
A24-4 - Body ground

for i-ART
Tester Connection Condition Specified Condition
A24-1 - G157-8 (STP) Always Below 1 Ω
A24-4 - G157-9 (ST1-)
A24-1 - Body ground Always 10 kΩ or higher
A24-4 - Body ground



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR