In this circuit, the combination meter assembly receives engine speed signals from the ECM. The meter CPU displays the engine speed, which is calculated based on the data received from the ECM.
| *a | Front view of wire harness connector
(to Combination Meter Assembly) |
Disconnect the G19 combination meter assembly connector.
Using an oscilloscope, check the signal waveform of the meter.
| Item | Content |
|---|---|
| Tester Connection | G19-7 (S) - Body ground |
| Tool Setting | 5 V/DIV., 10 msec./DIV. |
| Condition | Engine idling |
As the engine speed increases, the wavelength shortens.
The waveform displayed is as shown in the illustration.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the engine type.
| Result | Proceed to |
|---|---|
| for Gasoline Engine | A |
| for Diesel Engine | B |
A
B
Disconnect the G19 combination meter assembly connector.
Disconnect the G88*1, G146*2 or G154*3 ECM connector.
*1: for 2TR-FE
*2: for 2TR-FBE
*3: for 1GR-FE
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G19-7 (S) - G88-1 (TACH) | Always | Below 1 Ω |
| G19-7 (S) or G88-1 (TACH) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G19-7 (S) - G146-29 (TACH) | Always | Below 1 Ω |
| G19-7 (S) or G146-29 (TACH) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G19-7 (S) - G154-1 (TACH) | Always | Below 1 Ω |
| G19-7 (S) or G154-1 (TACH) - Body ground | Always | 10 kΩ or higher |
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
Refer to SFI system.
SFI system (1GR-FE):
Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
SFI system (2TR-FE [w/o Secondary Air Injection System]):
SFI system (2TR-FE [w/ Secondary Air Injection System]):
SFI system (2TR-FBE):
Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
A
B
Disconnect the G19 combination meter assembly connector.
Disconnect the G39*1, G149*2 or G157*3 ECM connector.
*1: for 1KD-FTV, 2KD-FTV
*2: for 1KD-FTV, 2KD-FTV (for DPF)
*3: for 1KD-FTV (for i-ART)
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G19-7 (S) - G39-4 (TACH) | Always | Below 1 Ω |
| G19-7 (S) or G39-4 (TACH) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G19-7 (S) - G149-18 (TACH) | Always | Below 1 Ω |
| G19-7 (S) or G149-18 (TACH) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G19-7 (S) - G157-18 (TACH) | Always | Below 1 Ω |
| G19-7 (S) or G157-18 (TACH) - Body ground | Always | 10 kΩ or higher |
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
Refer to ECD system.
ECD system (1KD-FTV [for DPF]):
ECD system (1KD-FTV [for i-ART]):
ECD system (1KD-FTV [w/o EGR Cooler]):
ECD system (1KD-FTV [w/ EGR Cooler]):
ECD system (2KD-FTV [for DPF]):
ECD system (2KD-FTV [w/o EGR Cooler]):
ECD system (2KD-FTV [w/ EGR Cooler]):
A
B