Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2012.10
RM1840EF _54 Brake _009623 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0052601 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1268  Transfer L4 Position Switch Circuit  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area
C1268 Transfer L4 Position Switch Circuit No signal is input to the EXI4 terminal of the skid control ECU.
·

L4 position switch (No. 1 transfer indicator switch)

·

L4 position switch circuit

·

Skid control ECU (Brake actuator assembly)

·

Transmission control ECU assembly (for Automatic Transmission)



*C1268: for 4WD

WIRING DIAGRAM

C237164
2.677,1 2.875,1.146 0.198,0.146 10 false 15 2.646,2.125 2.823,2.302 0.177,0.177 10 false 9 0.958,2.823 2.771,3.219 1.813,0.396 10 false Skid Control ECU (Brake Actuator Assembly) 4.135,2.979 6.083,3.354 1.948,0.375 10 false L4 Position Switch (No. 1 Transfer Indicator Switch) 0.958,2.656 1.375,2.844 0.417,0.188 10 false A36 0.938,1.563 1.333,1.771 0.396,0.208 10 false G40 0.938,1.719 3.344,1.948 2.406,0.229 10 false Transmission Control ECU Assembly 4.135,2.802 4.625,2.969 0.49,0.167 10 false C29 0.167,0.198 3.406,0.406 3.24,0.208 12 false for Automatic Transmission: 2.313,1.156 2.563,1.365 0.25,0.208 10 false L4 2.198,2.26 2.552,2.438 0.354,0.177 10 false EXI4 4.156,2.104 4.292,2.26 0.135,0.156 10 false 1 6,2.115 6.125,2.292 0.125,0.177 10 false 2

C190842
1.021,2.177 2.667,2.531 1.646,0.354 10 false Skid Control ECU (Brake Actuator Assembly) 4.125,2.094 6.063,2.531 1.938,0.438 10 false L4 Position Switch (No. 1 Transfer Indicator Switch) 1.021,2 1.344,2.188 0.323,0.188 10 false A36 4.125,1.927 4.479,2.094 0.354,0.167 10 false C29 0.115,0 3.323,0.208 3.208,0.208 12 false for Manual Transmission: 1.323,0.479 2.677,0.677 1.354,0.198 10 false from IG Circuit 2.75,1.458 2.927,1.635 0.177,0.177 10 false 9 4.188,1.458 4.323,1.615 0.135,0.156 10 false 1 5.615,1.458 5.74,1.635 0.125,0.177 10 false 2 2.271,1.51 2.656,1.677 0.385,0.167 10 false EXI4

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the brake actuator assembly, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).

·

Before disconnecting the connector, make sure that there are no problems with the connection.

·

After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.



PROCEDURE

1.CHECK TERMINAL VOLTAGE (EXI4 TERMINAL)
a.
C199357
0.125,0.969 0.469,1.198 0.344,0.229 2.083,0.844 1.906,0.24 1.906,0.24 1.76,0.24 false 0.094,0.052 0.406,0.208 0.313,0.156 10 false *a 1.448,0.156 1.917,0.406 0.469,0.25 10 false EXI4 0.177,1.01 0.646,1.26 0.469,0.25 10 false A36
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Connect the skid control ECU (brake actuator assembly) connector.


b.

Set the vehicle to the L4 state using the transfer shift lever.


c.

Disconnect the skid control ECU (brake actuator assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A36-9 (EXI4) - Body ground
·

Ignition switch ON

·

Transfer shift position L4


Below 1.5 V



e.

Connect the skid control ECU (brake actuator assembly) connector.


f.

Set the vehicle to the H4 or H2 state using the transfer shift lever.


g.

Disconnect the skid control ECU (brake actuator assembly) connector.


h.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A36-9 (EXI4) - Body ground
·

Ignition switch ON

·

Transfer shift position not L4


11 to 14 V



Result:
Proceed to
OK
NG



OK

2.RECONFIRM DTC

NG

3.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - L4 POSITION SWITCH)
2.RECONFIRM DTC
a.

Clear the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTC is output A
DTC is not output B




A

B

3.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - L4 POSITION SWITCH)
a.

Turn the ignition switch off.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.

for Automatic Transmission: Disconnect the G40 transmission control ECU connector.


d.

Disconnect the L4 position switch (No. 1 transfer indicator switch) connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A36-9 (EXI4) - C29-1 Always Below 1 Ω
A36-9 (EXI4) - Body ground Always 10 kΩ or higher
C29-2 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT L4 POSITION SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT L4 POSITION SWITCH
a.

Turn the ignition switch off.


b.

Remove the L4 position switch (No. 1 transfer indicator switch).

Click hereDrivetrain>VF2A TRANSFER / 4WD / AWD>TRANSFER INDICATOR SWITCH>REMOVAL


c.

Inspect the L4 position switch (No. 1 transfer indicator switch).

Click hereDrivetrain>VF2A TRANSFER / 4WD / AWD>TRANSFER INDICATOR SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK TERMINAL VOLTAGE (L4 POSITION SWITCH POWER SOURCE CIRCUIT)

NG

REPLACE NO. 1 TRANSFER INDICATOR SWITCH

5.CHECK TERMINAL VOLTAGE (L4 POSITION SWITCH POWER SOURCE CIRCUIT)
a.
C239113
0.667,1.125 1.031,1.365 0.365,0.24 0.073,0.083 0.385,0.24 0.313,0.156 10 false *a 0.729,1.167 1.24,1.469 0.51,0.302 10 false C29
*a Front view of wire harness connector
(to L4 Position Switch [No. 1 Transfer Indicator Switch])


Turn the ignition switch off.


b.

Disconnect the L4 position switch (No. 1 transfer indicator switch) connector.


c.

Disconnect the skid control ECU (brake actuator assembly) connector.


d.

for Automatic Transmission: Connect the transmission control ECU connector.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
1 - 2 Ignition switch ON 11 to 14 V


Result:
Result Proceed to
OK A
NG (for Manual Transmission) B
NG (for Automatic Transmission) C




A

B

REPAIR OR REPLACE HARNESS OR CONNECTOR

C

6.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - TRANSMISSION CONTROL ECU)
6.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - TRANSMISSION CONTROL ECU)
a.

Turn the ignition switch off.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.

Disconnect the G40 transmission control ECU connector.


d.

Disconnect the L4 position switch (No. 1 transfer indicator switch) connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A36-9 (EXI4) - G40-15 (L4) Always Below 1 Ω
A36-9 (EXI4) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TRANSMISSION CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR