Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2012.04–2012.10
RM1840EF _54 Brake _009623 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0052601 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1426  Stop Light Switch OFF Stuck Malfunction  


DESCRIPTION

The skid control ECU (brake actuator assembly) receives stop light switch signals and brake operation condition information.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1426 Stop Light Switch OFF Stuck Malfunction When the brake pedal load sensing switch is on, the master cylinder pressure is 2 MPa or higher and the deceleration calculated from the vehicle speed is 0.2 G or more, the stop light switch is off for 2 seconds or more.
·

STOP fuse

·

Stop light switch

·

Stop light switch circuit

·

Skid control ECU (Brake actuator assembly)

·

Brake pedal height and stop light switch installation

·

Brake with switch pedal sub-assembly



CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the brake actuator assembly, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1422).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Before disconnecting the connector, make sure that there are no problems with the connection.

·

After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.



PROCEDURE

1.CHECK STOP LIGHT OPERATION
a.

Check that the stop light LH and RH come on when the brake pedal is depressed, and go off when the brake pedal is released.

OK:
Condition Illumination Condition
Brake pedal depressed On
Brake pedal released Off



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SW/BRAKE PEDAL LOAD SENSING SW)

NG

4.INSPECT STOP LIGHT SWITCH ASSEMBLY
2.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SW/BRAKE PEDAL LOAD SENSING SW)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-
Brake Pedal Load Sensing SW Brake pedal load sensing switch ON or OFF ON: Brake pedal depressed beyond specified point
OFF: Brake pedal not depressed beyond specified point
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
Stop Light SW
Brake Pedal Load Sensing SW
50003 105 37,39

f.

Check that the stop light switch display and brake pedal load sensing switch display observed on the intelligent tester change according to the brake pedal operation.

OK:

The intelligent tester displays ON or OFF according to brake pedal operation.



g.

Slowly depress the brake pedal and check when the stop light switch and brake pedal load sensing switch are turned on.

OK:

The stop light switch turns on first, and then the brake pedal load sensing switch turns on.


Result:
Result Proceed to
OK A
NG (Turning on of stop light switch is not confirmed) B
NG (Brake pedal load sensing switch turns on first) C




A

3.RECONFIRM DTC

B

5.CHECK TERMINAL VOLTAGE (STP TERMINAL)

C

6.ADJUST BRAKE PEDAL AND STOP LIGHT SWITCH INSTALLATION
3.RECONFIRM DTC
a.

Clear the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Depress the brake pedal several times to test the stop light circuit.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTC is not output A
DTC is output B




A

B

4.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Turn the ignition switch off.


b.

Remove the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL


c.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK TERMINAL VOLTAGE (STP TERMINAL)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

5.CHECK TERMINAL VOLTAGE (STP TERMINAL)
a.

Turn the ignition switch off.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.
C199357
0.219,0.99 0.542,1.198 0.323,0.208 1.292,0.844 1.563,0.177 1.563,0.177 1.75,0.177 false 0.073,0.073 0.385,0.229 0.313,0.156 10 false *a 1.792,0.104 2.292,0.354 0.5,0.25 10 false STP 0.26,1.01 0.76,1.26 0.5,0.25 10 false A36
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A36-2 (STP) - Body ground Brake pedal depressed 8 to 14 V
Brake pedal released Below 1.5 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.ADJUST BRAKE PEDAL AND STOP LIGHT SWITCH INSTALLATION
a.

Adjust the brake pedal height and stop light switch installation.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL(w/ VSC)>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

7.RECONFIRM DTC
7.RECONFIRM DTC
a.

Clear the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Depress the brake pedal several times to test the stop light circuit.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTC is not output A
DTC is output B




A

END

B

REPLACE BRAKE WITH SWITCH PEDAL SUB-ASSEMBLY