Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2012.10
RM1840EF _54 Brake _009623 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0052601 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1430  Brake Pedal Load Sensing Switch OFF Stuck Malfunction  C1431  Brake Pedal Load Sensing Switch ON Stuck Malfunction  


DESCRIPTION

The brake pedal load sensing switch operates when the brake pedal is depressed with a force exceeding a predetermined level.

The skid control ECU (brake actuator assembly) detects if the brake pedal is depressed or not via this circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1430 Brake Pedal Load Sensing Switch OFF Stuck Malfunction Either condition is met:
1.

With the stop light switch on, the brake pedal load sensing switch off and the master cylinder pressure at 6 MPa or more, the deceleration is 0.4 G or more for 1 second or more.

2.

With the stop light switch on, the brake pedal load sensing switch off and the master cylinder pressure at 6 MPa or more, the vehicle speed is 0 km/h (0 mph) for 5 seconds or more.


·

Brake pedal load sensing switch (Brake with switch pedal sub-assembly)

·

Brake pedal load sensing switch circuit

·

Skid control ECU (Brake actuator assembly)

·

Brake pedal height and stop light switch installation

·

Brake with switch pedal sub-assembly


C1431 Brake Pedal Load Sensing Switch ON Stuck Malfunction Either condition is met:
1.

Immediately after the ignition switch is turned to ON, the brake pedal load sensing switch is on and the stop light switch is off for 10 seconds or more.

2.

The condition that the brake pedal load sensing switch remains on while the vehicle speed increases from 0 km/h (0 mph) to 30 km/h (18 mph) occurs 5 times in succession.


·

Brake pedal load sensing switch (Brake with switch pedal sub-assembly)

·

Brake pedal load sensing switch circuit

·

Skid control ECU (Brake actuator assembly)

·

Brake pedal height and stop light switch installation

·

Brake with switch pedal sub-assembly



CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the brake actuator assembly, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).

·

Before disconnecting the connector, make sure that there are no problems with the connection.

·

After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.



HINT:

When DTC C1425 is output together with DTC C1430 and/or C1431, inspect and repair the trouble areas indicated by DTC C1425 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1425).


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SW/BRAKE PEDAL LOAD SENSING SW)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-
Brake Pedal Load Sensing SW Brake pedal load sensing switch ON or OFF ON: Brake pedal depressed beyond specified point
OFF: Brake pedal not depressed beyond specified point
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
Stop Light SW
Brake Pedal Load Sensing SW
50003 105 37,39

f.

Check that the stop light switch display and brake pedal load sensing switch display observed on the intelligent tester change according to the brake pedal operation.

OK:

The intelligent tester displays ON or OFF according to brake pedal operation.



g.

Slowly depress the brake pedal and check when the stop light switch and brake pedal load sensing switch are turned on.

OK:

The stop light switch turns on first, and then the brake pedal load sensing switch turns on.


Result:
Result Proceed to
OK A
NG (Turning on of brake pedal load sensing switch is not confirmed) B
NG (Brake pedal load sensing switch turns on first) C




A

2.RECONFIRM DTC

B

3.INSPECT BRAKE PEDAL LOAD SENSING SWITCH

C

5.CHECK BRAKE PEDAL AND STOP LIGHT SWITCH INSTALLATION
2.RECONFIRM DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 40 km/h (25 mph) or more and perform a braking test (decelerate the vehicle by depressing the brake pedal).


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTC is not output A
DTC is output B




A

B

3.INSPECT BRAKE PEDAL LOAD SENSING SWITCH
C190633
1,1.74 1,1.552 1,1.552 1.958,1.073 false 3.208,2.74 3.208,2.667 3.208,2.667 2.625,2.521 false 4.583,1.792 4.76,1.792 4.76,1.792 5.208,2.417 false 4.729,3.125 4.833,3.125 4.833,3.125 5.198,2.479 false 0.948,1.792 1.26,1.948 0.313,0.156 10 false *1 3.156,2.781 3.469,2.938 0.313,0.156 10 false *2 4.938,0.729 5.25,0.885 0.313,0.156 10 false *a 4.385,1.719 4.698,1.875 0.313,0.156 10 false *b 4.552,3.031 4.865,3.188 0.313,0.156 10 false *c 4.656,2.313 4.896,2.552 0.24,0.24 10 false 2 6.042,2.302 6.281,2.542 0.24,0.24 10 false 1
*1 Brake Pedal Load Sensing Switch *2 Brake with Switch Pedal Sub-assembly
*a Component without harness connected
(Brake Pedal Load Sensing Switch)
*b Brake Pedal Released (Closed)
*c Brake Pedal Depressed (Open) - -


NOTICE:
·

Do not remove the brake pedal load sensing switch from the brake with switch pedal sub-assembly.

·

When there is a malfunction in the brake pedal load sensing switch, replace the brake with switch pedal sub-assembly.



a.

Turn the ignition switch off.


b.

Disconnect the brake pedal load sensing switch (brake with switch pedal sub-assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 - 1 Brake pedal depressed 950 to 1050 Ω
Brake pedal released 203 to 223 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BRAKE PEDAL LOAD SENSING SWITCH)

NG

REPLACE BRAKE WITH SWITCH PEDAL SUB-ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BRAKE PEDAL LOAD SENSING SWITCH)
a.

Turn the ignition switch off.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.

Disconnect the brake pedal load sensing switch (brake with switch pedal sub-assembly) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A36-27 (FSW+) - A35-2 Always Below 1 Ω
A36-27 (FSW+) - Body ground Always 10 kΩ or higher
A35-1 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK BRAKE PEDAL AND STOP LIGHT SWITCH INSTALLATION
a.

Turn the ignition switch off.


b.

Check the brake pedal height and stop light switch installation.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL(w/ VSC)>INSTALLATION

OK:

The brake pedal height and stop light switch installation are normal.



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE WITH SWITCH PEDAL SUB-ASSEMBLY

NG

ADJUST BRAKE PEDAL OR STOP LIGHT SWITCH