Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM › from 2012.10
RM1840EF _58 Vehicle Interior _009641 THEFT DETERRENT / KEYLESS ENTRY _0052689 ENGINE IMMOBILISER SYSTEM C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM  B279A  Theft Deterrent System Communication Line High Fixation  


DESCRIPTION

If the communication line (EFIO-IMI) to the transponder key ECU assembly is stuck on HI output, the ECM stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B279A Theft Deterrent System Communication Line High Fixation The communication line (EFIO-IMI) between the ECM and transponder key ECU assembly is stuck on HI output (1 trip detection logic*1).
·

Harness or connector

·

Transponder key ECU assembly

·

ECM

·

Telephone transceiver assembly*2


Detection Enabling Condition (DTC Output Confirmation Operation)

Turn the ignition switch to ON and wait 6 seconds.



*1: Only output while a malfunction is present.

*2: w/ Blocking System


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started (initial ignition occurs and engine cranks, then ignition stop). Engine cannot be started.

Related Data List and Active Test
DTC Code Data List and Active Test
B279A -

WIRING DIAGRAM

B315871
5.5,0.604 5.74,0.781 0.24,0.177 10 false +B 4.708,0.74 5.177,0.917 0.469,0.177 10 false ECU-B 4.25,0.74 4.583,0.917 0.333,0.177 10 false DCC 1.125,1.844 1.5,2.021 0.375,0.177 10 false ECM 2.948,0.615 3.729,0.792 0.781,0.177 10 false from Battery 5.281,0.51 5.417,0.688 0.135,0.177 10 false 1 5.5,1 5.854,1.177 0.354,0.177 10 false EFIO 1.5,1.01 1.729,1.188 0.229,0.177 10 false IMI 5.229,0.927 5.417,1.104 0.188,0.177 10 false 13 5.5,1.458 5.865,1.635 0.365,0.177 10 false GND 4.844,1.781 5.177,1.938 0.333,0.156 10 false G26 4.844,1.927 6.927,2.104 2.083,0.177 10 false Transponder Key ECU Assembly 5.219,1.365 5.417,1.542 0.198,0.177 10 false 16 1.792,1.01 2.073,1.177 0.281,0.167 10 false G38 1.792,1.229 2.104,1.396 0.313,0.167 10 false 30*1 2.219,1.01 2.5,1.177 0.281,0.167 10 false G88 2.219,1.229 2.531,1.396 0.313,0.167 10 false 16*2 2.573,1.01 2.948,1.177 0.375,0.167 10 false G146 2.604,1.219 2.917,1.385 0.313,0.167 10 false 31*3 2.969,1.01 3.344,1.177 0.375,0.167 10 false G148 3.01,1.229 3.323,1.396 0.313,0.167 10 false 28*4 3.365,1.01 3.74,1.177 0.375,0.167 10 false G156 3.406,1.229 3.719,1.396 0.313,0.167 10 false 28*5 0.094,2.24 4.177,2.521 4.083,0.281 10 false *1: for 1KD-FTV (except DPF and i-ART), 2KD-FTV (except DPF) 0.063,0.063 1.75,0.365 1.688,0.302 12 false w/o Blocking System: 0.094,2.521 1.031,2.719 0.938,0.198 10 false *2: for 2TR-FE 0.094,2.792 1.125,2.99 1.031,0.198 10 false *3: for 2TR-FBE 0.094,3.063 3.031,3.26 2.938,0.198 10 false *4: for 1KD-FTV (for DPF), 2KD-FTV (for DPF) 0.094,3.344 1.885,3.542 1.792,0.198 10 false *5: for 1KD-FTV (for i-ART)

B315872
5.5,0.375 5.74,0.552 0.24,0.177 10 false +B 4.708,0.531 5.177,0.708 0.469,0.177 10 false ECU-B 4.25,0.521 4.583,0.698 0.333,0.177 10 false DCC 1.125,2.063 1.5,2.24 0.375,0.177 10 false ECM 2.948,0.375 3.729,0.552 0.781,0.177 10 false from Battery 5.281,0.292 5.417,0.469 0.135,0.177 10 false 1 5.5,1.229 5.854,1.406 0.354,0.177 10 false EFIO 1.5,1.229 1.729,1.406 0.229,0.177 10 false IMI 5.229,1.146 5.417,1.323 0.188,0.177 10 false 13 5.5,1.667 5.865,1.844 0.365,0.177 10 false GND 4.844,2.021 5.177,2.177 0.333,0.156 10 false G26 4.844,2.167 6.938,2.406 2.094,0.24 10 false Transponder Key ECU Assembly 3.333,1.823 3.729,1.979 0.396,0.156 10 false G144 3.333,1.969 4.594,2.385 1.26,0.417 10 false Telephone Receiver Assembly 5.219,1.594 5.417,1.771 0.198,0.177 10 false 16 1.802,1.229 2.083,1.396 0.281,0.167 10 false G38 1.792,1.458 2.104,1.625 0.313,0.167 10 false 30*1 2.167,1.229 2.542,1.396 0.375,0.167 10 false G146 2.219,1.458 2.531,1.625 0.313,0.167 10 false 31*2 2.573,1.229 2.948,1.396 0.375,0.167 10 false G148 2.604,1.458 2.917,1.625 0.313,0.167 10 false 28*3 2.958,1.229 3.333,1.396 0.375,0.167 10 false G156 3.01,1.458 3.323,1.625 0.313,0.167 10 false 28*4 3.625,1.156 4,1.323 0.375,0.167 10 false BLK3 4.177,1.156 4.552,1.323 0.375,0.167 10 false BLK4 3.479,1.156 3.594,1.323 0.115,0.167 10 false 8 4.594,1.156 4.708,1.323 0.115,0.167 10 false 2 0.094,2.615 4.156,2.833 4.063,0.219 10 false *1: for 1KD-FTV (except DPF and i-ART), 2KD-FTV (except DPF) 0.052,0.042 1.75,0.375 1.698,0.333 12 false w/ Blocking System: 0.094,2.885 1.177,3.083 1.083,0.198 10 false *2: for 2TR-FBE 0.094,3.167 3.073,3.365 2.979,0.198 10 false *3: for 1KD-FTV (for DPF), 2KD-FTV (for DPF) 0.094,3.427 1.844,3.625 1.75,0.198 10 false *4: for 1KD-FTV (for i-ART)

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the transponder key ECU assembly, ECM or telephone transceiver assembly (w/ Blocking System), refer to the Service Bulletin.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:
w/ Blocking System:

After troubleshooting for this DTC, make sure B279A is not present. If present, troubleshoot the blocking system DTCs next.


PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR

Result:
Result Proceed to
No DTC is output A
DTC B279A and other DTCs are output B
DTC B279A is output C


HINT:

If any DTCs other than B279A are output, troubleshoot those DTCs first.




A

B

C

3.CHECK HARNESS AND CONNECTOR (SFI OR ECD COMMUNICATION LINE)
3.CHECK HARNESS AND CONNECTOR (SFI OR ECD COMMUNICATION LINE)
a.

Disconnect the G26 transponder key ECU assembly connector.


b.

Disconnect the G38*1, G88*2, G146*3, G148*4 or G156*5ECM connector.

*1: for 1KD-FTV (except DPF and i-ART), 2KD-FTV (except DPF)

*2: for 2TR-FE

*3: for 2TR-FBE

*4: for 1KD-FTV (for DPF), 2KD-FTV (for DPF)

*5: 1KD-FTV (for i-ART)



c.

w/ Blocking System:

i.

Disconnect the G144 telephone transceiver assembly connector.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1KD-FTV (except DPF and i-ART), 2KD-FTV (except DPF) [w/o Blocking System]:
Tester Connection Condition Specified Condition
G26-13 (EFIO) - G38-30 (IMI) Always Below 1 Ω
G26-13 (EFIO) or G38-30 (IMI) - Body ground Always 10 kΩ or higher

for 1KD-FTV (except DPF and i-ART), 2KD-FTV (except DPF) [w/ Blocking System]:
Tester Connection Condition Specified Condition
G26-13 (EFIO) - G144-2 (BLK4) Always Below 1 Ω
G144-8 (BLK3) - G38-30 (IMI) Always Below 1 Ω
G26-13 (EFIO) or G144-2 (BLK4) - Body ground Always 10 kΩ or higher
G144-8 (BLK3) or G38-30 (IMI) - Body ground Always 10 kΩ or higher

for 2TR-FE:
Tester Connection Condition Specified Condition
G26-13 (EFIO) - G88-16 (IMI) Always Below 1 Ω
G26-13 (EFIO) or G88-16 (IMI) - Body ground Always 10 kΩ or higher

for 2TR-FBE (w/o Blocking System):
Tester Connection Condition Specified Condition
G26-13 (EFIO) - G146-31 (IMI) Always Below 1 Ω
G26-13 (EFIO) or G146-31 (IMI) - Body ground Always 10 kΩ or higher

for 2TR-FBE (w/ Blocking System):
Tester Connection Condition Specified Condition
G26-13 (EFIO) - G144-2 (BLK4) Always Below 1 Ω
G144-8 (BLK3) - G146-31 (IMI) Always Below 1 Ω
G26-13 (EFIO) or G144-2 (BLK4) - Body ground Always 10 kΩ or higher
G144-8 (BLK3) or G146-31 (IMI) - Body ground Always 10 kΩ or higher

for 1KD-FTV (for DPF), 2KD-FTV (for DPF) [w/o Blocking System]:
Tester Connection Condition Specified Condition
G26-13 (EFIO) - G148-28 (IMI) Always Below 1 Ω
G26-13 (EFIO) or G148-28 (IMI) - Body ground Always 10 kΩ or higher

for 1KD-FTV (except DPF and i-ART), 2KD-FTV (except DPF) [w/ Blocking System]:
Tester Connection Condition Specified Condition
G26-13 (EFIO) - G144-2 (BLK4) Always Below 1 Ω
G144-8 (BLK3) - G148-28 (IMI) Always Below 1 Ω
G26-13 (EFIO) or G144-2 (BLK4) - Body ground Always 10 kΩ or higher
G144-8 (BLK3) or G148-28 (IMI) - Body ground Always 10 kΩ or higher

for 1KD-FTV (for i-ART) [w/o Blocking System]:
Tester Connection Condition Specified Condition
G26-13 (EFIO) - G156-28 (IMI) Always Below 1 Ω
G26-13 (EFIO) or G156-28 (IMI) - Body ground Always 10 kΩ or higher

for 1KD-FTV (for i-ART) [w/ Blocking System]:
Tester Connection Condition Specified Condition
G26-13 (EFIO) - G144-2 (BLK4) Always Below 1 Ω
G144-8 (BLK3) - G156-28 (IMI) Always Below 1 Ω
G26-13 (EFIO) or G144-2 (BLK4) - Body ground Always 10 kΩ or higher
G144-8 (BLK3) or G156-28 (IMI) - Body ground Always 10 kΩ or higher



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for 1KD-FTV (except DPF and i-ART), 2KD-FTV (except DPF) [w/o Blocking System]:
Tester Connection Condition Specified Condition
G26-13 (EFIO) or G38-30 (IMI) - Body ground Always Below 1 V

for 1KD-FTV (except DPF and i-ART), 2KD-FTV (except DPF) [w/ Blocking System]:
Tester Connection Condition Specified Condition
G26-13 (EFIO) or G144-2 (BLK4) - Body ground Always Below 1 V
G144-8 (BLK3) or G38-30 (IMI) - Body ground Always Below 1 V

for 2TR-FE:
Tester Connection Condition Specified Condition
G26-13 (EFIO) or G88-16 (IMI) - Body ground Always Below 1 V

for 2TR-FBE (w/o Blocking System):
Tester Connection Condition Specified Condition
G26-13 (EFIO) or G146-31 (IMI) - Body ground Always Below 1 V

for 2TR-FBE (w/ Blocking System):
Tester Connection Condition Specified Condition
G26-13 (EFIO) or G144-2 (BLK4) - Body ground Always Below 1 V
G144-8 (BLK3) or G146-31 (IMI) - Body ground Always Below 1 V

for 1KD-FTV (for DPF), 2KD-FTV (for DPF) [w/o Blocking System]:
Tester Connection Condition Specified Condition
G26-13 (EFIO) or G148-28 (IMI) - Body ground Always Below 1 V

for 1KD-FTV (for DPF), 2KD-FTV (for DPF) [w/ Blocking System]:
Tester Connection Condition Specified Condition
G26-13 (EFIO) or G144-2 (BLK4) - Body ground Always Below 1 V
G144-8 (BLK3) or G148-28 (IMI) - Body ground Always Below 1 V

for 1KD-FTV (for i-ART) [w/o Blocking System]:
Tester Connection Condition Specified Condition
G26-13 (EFIO) or G156-28 (IMI) - Body ground Always Below 1 V

for 1KD-FTV (for i-ART) [w/ Blocking System]:
Tester Connection Condition Specified Condition
G26-13 (EFIO) or G144-2 (BLK4) - Body ground Always Below 1 V
G144-8 (BLK3) or G156-28 (IMI) - Body ground Always Below 1 V



Result:
Proceed to
OK
NG



OK

4.CHECK TRANSPONDER KEY ECU ASSEMBLY (TERMINAL EFIO)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK TRANSPONDER KEY ECU ASSEMBLY (TERMINAL EFIO)
a.
B274402
0.688,1.24 1.052,1.531 0.365,0.292 0.823,1.833 1.177,1.833 1.177,1.833 1.302,1.448 true 1.063,2.125 1.323,2.125 1.323,2.125 1.552,1.448 true 0.073,2.438 0.385,2.594 0.313,0.156 10 false *1 0.052,0.063 0.365,0.219 0.313,0.156 10 false *a 0.5,1.75 0.958,1.948 0.458,0.198 10 false GND 0.719,2.042 1.333,2.24 0.615,0.198 10 false EFIO 0.74,1.302 1.198,1.5 0.458,0.198 10 false G26 0.26,3.354 0.719,3.552 0.458,0.198 10 false GND
*1 Waveform
*a Component with harness connected(Transponder Key ECU Assembly)


Using an oscilloscope, check the waveform.

Measurement Condition:
Item Content
Tester Connection G26-13 (EFIO) - G26-16 (GND)
Tool Setting 10V/DIV., 100 ms./DIV.
Condition Ignition switch ON


HINT:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


OK:

Waveform is output normally (refer to illustration).



Result:
Proceed to
OK
NG



OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

5.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - BATTERY AND BODY GROUND)
5.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - BATTERY AND BODY GROUND)
a.
B274403
0.354,1.281 0.719,1.604 0.365,0.323 2.844,1.917 2.646,1.917 2.646,1.917 2.406,1.552 false 0.448,1.021 0.667,1.021 0.667,1.021 0.99,1.281 false 0.063,0.063 0.375,0.219 0.313,0.156 10 false *a 0.229,0.938 0.542,1.135 0.313,0.198 10 false +B 2.875,1.844 3.333,2.042 0.458,0.198 10 false GND 0.406,1.365 0.865,1.563 0.458,0.198 10 false G26
*a Front view of wire harness connector
(to Transponder Key ECU Assembly)


Disconnect the G26 transponder key ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Connection Specified Condition
G26-16 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G26-1 (+B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.REPLACE ECM
a.

Temporarily replace the ECM with a new one.



Result:
Proceed to
NEXT



NEXT

7.REGISTER ECU COMMUNICATION ID
7.REGISTER ECU COMMUNICATION ID
a.

Register the ECU - ECM communication ID (Refer to the Service Bulletin).


Result:
Proceed to
NEXT



NEXT

8.CLEAR DTC
8.CLEAR DTC

NEXT

9.CHECK FOR DTC
9.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR

OK:

DTC B279A is not output.


Result:
Result Proceed to
OK A
NG (w/o Blocking System) B
NG (w/ Blocking System) C




A

END (ECM IS DEFECTIVE)

B

REPLACE TRANSPONDER KEY ECU ASSEMBLY

C

10.REPLACE TRANSPONDER KEY ECU ASSEMBLY
10.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Temporarily replace the transponder key ECU assembly with a new one (Refer to the service Bulletin).


Result:
Proceed to
NEXT



NEXT

11.REGISTER ECU COMMUNICATION ID
11.REGISTER ECU COMMUNICATION ID
a.

Register the ECU - ECM communication ID (Refer to the Service Bulletin).


Result:
Proceed to
NEXT



NEXT

12.CLEAR DTC
12.CLEAR DTC

NEXT

13.CHECK FOR DTC
13.CHECK FOR DTC
a.

Result:
Proceed to
OK
NG



OK

END (TRANSPONDER KEY ECU IS DEFECTIVE)

NG

REPLACE TELEPHONE TRANSCEIVER ASSEMBLY