When the communication line (EFIO - BLK4) between the transponder key ECU assembly and telephone transceiver assembly is stuck on HI output while ignition switch is ON, the telephone transceiver assembly stores DTC B1586.
Before troubleshooting for these DTCs, make sure no engine immobiliser system DTCs are present. If present, troubleshoot the engine immobiliser system DTCs first.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B1586 | Open in Immobiliser Communication Circuit | The communication line (EFIO - BLK4) between the transponder key ECU assembly and telephone transceiver assembly is stuck on HI while ignition switch is ON. | ·
Telephone transceiver assembly ·
Transponder key ECU assembly ·
ECM ·
Harness or connector |
When replacing the telephone transceiver assembly, transponder key ECU assembly or ECM, refer to the Service Bulletin.
When the telephone transceiver assembly is replaced, it is necessary to set the contract mode.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Clear the DTCs.
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>BLOCKING SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>BLOCKING SYSTEM>DTC CHECK / CLEAR
DTC B1586 is not output.
| Result | Proceed to |
|---|---|
| DTC B1586 is output | A |
| DTC B1586 and other DTCs are output | B |
A
B
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>BLOCKING SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
Disconnect the G144 telephone transceiver assembly connector.
Disconnect the G38*1, G146*2, G148*3 or G156*4 ECM connector.
*1: for 1KD-FTV (except DPF and i-ART), 2KD-FTV (except DPF)
*2: for 2TR-FBE
*3: for 1KD-FTV (for DPF), 2KD-FTV (for DPF)
*4: for 1KD-FTV (for i-ART)
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G144-8 (BLK3) - G38-30 (IMI) | Always | Below 1 Ω |
| G144-8 (BLK3) or G38-30 (IMI) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G144-8 (BLK3) - G146-31 (IMI) | Always | Below 1 Ω |
| G144-8 (BLK3) or G146-31 (IMI) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G144-8 (BLK3) - G148-28 (IMI) | Always | Below 1 Ω |
| G144-8 (BLK3) or G148-28 (IMI) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G144-8 (BLK3) - G156-28 (IMI) | Always | Below 1 Ω |
| G144-8 (BLK3) or G156-28 (IMI) - Body ground | Always | 10 kΩ or higher |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G144-8 (BLK3) or G38-30 (IMI) - Body ground | Always | Below 1 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G144-8 (BLK3) or G146-31 (IMI) - Body ground | Always | Below 1 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G144-8 (BLK3) or G148-28 (IMI) - Body ground | Always | Below 1 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G144-8 (BLK3) or G156-28 (IMI) - Body ground | Always | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G144 telephone transceiver assembly connector.
Disconnect the G26 transponder key ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G144-2 (BLK4) - G26-13 (EFIO) | Always | Below 1 Ω |
| G144-2 (BLK4) or G26-13 (EFIO) - Body ground | Always | 10 kΩ or higher |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G144-2 (BLK4) or G26-13 (EFIO) - Body ground | Always | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Waveform |
| *a | Component with harness connected
(Transponder Key ECU Assembly) |
Using an oscilloscope, check the waveform.
| Item | Content |
|---|---|
| Tester Connection | G26-13 (EFIO) - G26-16 (GND) |
| Tool Setting | 10V/DIV., 100 ms./DIV. |
| Condition | Ignition switch ON |
The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
Waveform is output normally (refer to illustration).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Telephone Transceiver Assembly) |
Disconnect the G144 telephone transceiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G144-9 (E) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G144-12 (+B) - G144-9 (E) | Always | 11 to 14 V |
| G144-6 (IG2) - G144-9 (E) | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Temporarily replace the ECM with a new one.
for 2TR-FBE:
Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>ECM>REMOVAL
for 1KD-FTV:
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECM>REMOVAL
for 2KD-FTV:
Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Reregister the ECU - ECM communication ID (Refer to the Service Bulletin).
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>BLOCKING SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>BLOCKING SYSTEM>DTC CHECK / CLEAR
DTC B1586 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Temporarily replace the transponder key ECU assembly with a new one (Refer to the Service Bulletin).
| Proceed to |
|---|
| NEXT |
NEXT
Reregister the ECU - ECM communication ID (Refer to the Service Bulletin).
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>BLOCKING SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>BLOCKING SYSTEM>DTC CHECK / CLEAR
DTC B1586 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG