Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › BLOCKING SYSTEM › from 2012.10
RM1840EF _58 Vehicle Interior _009641 THEFT DETERRENT / KEYLESS ENTRY _0052695 BLOCKING SYSTEM C

THEFT DETERRENT / KEYLESS ENTRY  BLOCKING SYSTEM  B1587  Lost Communication for Immobiliser Communication Circuit  


DESCRIPTION

When one of the following occurs: 1) the telephone transceiver assembly detects errors in its own communications with the transponder key ECU assembly; 2) the telephone transceiver assembly detects errors in the communication lines; 3) the ECU communication ID between the transponder key ECU assembly and telephone transceiver assembly is different and an engine start is attempt, the telephone transceiver assembly stores DTC B1587.

HINT:

Before troubleshooting for these DTCs, make sure no engine immobiliser system DTCs are present. If present, troubleshoot the engine immobiliser system DTCs first.


DTC No. Detection Item DTC Detection Condition Trouble Area
B1587 Lost Communication for Immobiliser Communication Circuit Either condition is met:
·

Error in communication between telephone transceiver assembly and transponder key ECU assembly

·

Error in communication lines

·

Communication ID is different during communication with transponder key ECU assembly


·

Telephone transceiver assembly

·

Transponder key ECU assembly

·

ECM

·

Harness or connector



WIRING DIAGRAM

B315874
3.021,3.042 4.458,3.438 1.438,0.396 10 false Telephone Transceiver Assembly 0.063,2.406 2.667,2.833 2.604,0.427 10 false *1: for 1KD-FTV (except DPF and i-ART), 2KD-FTV (except DPF) 0.063,2.854 1.115,3.052 1.052,0.198 10 false *2: for 2TR-FBE 0.063,3.115 2.917,3.313 2.854,0.198 10 false *3: for 1KD-FTV (for DPF) 2KD-FTV (for DPF) 0.063,3.396 1.792,3.594 1.729,0.198 10 false *4: for 1KD-FTV (for i-ART) 3.021,2.865 3.417,3.031 0.396,0.167 10 false G144 6.531,2.396 6.927,2.573 0.396,0.177 10 false ECM 0.917,1.594 2.01,2 1.094,0.406 10 false Transponder Key ECU Assembly 0.917,1.438 1.198,1.604 0.281,0.167 10 false G26 2.99,0.688 3.354,0.854 0.365,0.167 10 false BLK1 2.833,0.698 2.948,0.865 0.115,0.167 10 false 1 1.885,0.688 2.083,0.854 0.198,0.167 10 false 12 2.833,0.99 2.948,1.156 0.115,0.167 10 false 2 4.26,1.646 4.417,1.813 0.156,0.167 10 false 7 4.26,1.938 4.438,2.104 0.177,0.167 10 false 8 5.958,1.51 6.302,1.677 0.344,0.167 10 false 29*4 5.917,1.729 6.292,1.896 0.375,0.167 10 false G156 5.917,2.01 6.292,2.177 0.375,0.167 10 false G156 5.969,2.229 6.281,2.396 0.313,0.167 10 false 28*4 5.552,1.51 5.896,1.677 0.344,0.167 10 false 29*3 5.531,1.729 5.896,1.896 0.365,0.167 10 false G148 5.531,2.01 5.896,2.177 0.365,0.167 10 false G148 5.573,2.229 5.885,2.396 0.313,0.167 10 false 28*3 5.156,1.51 5.5,1.677 0.344,0.167 10 false 32*2 5.125,1.729 5.5,1.896 0.375,0.167 10 false G146 5.135,2.021 5.51,2.188 0.375,0.167 10 false G146 5.177,2.229 5.49,2.396 0.313,0.167 10 false 31*2 4.75,1.521 5.094,1.688 0.344,0.167 10 false 29*1 4.76,1.719 5.052,1.885 0.292,0.167 10 false G38 4.771,2.021 5.063,2.188 0.292,0.167 10 false G38 4.771,2.229 5.083,2.396 0.313,0.167 10 false 30*1 4.625,0.531 5.104,0.698 0.479,0.167 10 false ECU-B 5.354,0.531 5.708,0.698 0.354,0.167 10 false DCC 1.885,0.99 2.083,1.156 0.198,0.167 10 false 13 0.865,0.844 1.063,1.01 0.198,0.167 10 false 16 1.531,0.771 1.844,0.938 0.313,0.167 10 false EFII 1.49,1.073 1.844,1.24 0.354,0.167 10 false EFIO 1.104,0.948 1.427,1.115 0.323,0.167 10 false GND 2.99,0.979 3.354,1.146 0.365,0.167 10 false BLK4 3.823,1.635 4.188,1.802 0.365,0.167 10 false BLK2 4.24,0.333 4.417,0.5 0.177,0.167 10 false 12 3.99,0.427 4.188,0.594 0.198,0.167 10 false +B 4.26,2.281 4.438,2.448 0.177,0.167 10 false 9 4.063,2.354 4.177,2.521 0.115,0.167 10 false E 6.292,0.417 7.125,0.635 0.833,0.219 10 false from Battery 4.708,0.823 5.01,0.99 0.302,0.167 10 false IGN 4.26,0.625 4.438,0.792 0.177,0.167 10 false 6 3.948,0.698 4.208,0.865 0.26,0.167 10 false IG2 5.448,0.698 6.75,1.167 1.302,0.469 10 false from Ignition Switch Assembly 3.823,1.927 4.188,2.094 0.365,0.167 10 false BLK3 2.99,2.188 4.146,2.542 1.156,0.354 10 false Communication Switch 6.344,1.729 6.708,1.896 0.365,0.167 10 false IMO 6.344,2.042 6.708,2.208 0.365,0.167 10 false IMI

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the telephone transceiver assembly, transponder key ECU assembly or ECM, refer to the Service Bulletin.

·

When the telephone transceiver assembly is replaced, it is necessary to set the contract mode.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CLEAR DTC

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>BLOCKING SYSTEM>DTC CHECK / CLEAR

OK:

DTC B1587 is not output.



Result:
Proceed to
OK
NG



OK

NG

3.REREGISTER ECU COMMUNICATION ID
3.REREGISTER ECU COMMUNICATION ID
a.

Reregister the ECU - ECM communication ID (Refer to the Service Bulletin).


Result:
Proceed to
NEXT



NEXT

4.CLEAR DTC
4.CLEAR DTC

Result:
Proceed to
NEXT



NEXT

5.CHECK FOR DTC
5.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>BLOCKING SYSTEM>DTC CHECK / CLEAR

OK:

DTC B1587 is not output.



Result:
Proceed to
OK
NG



OK

END

NG

6.CHECK CONNECTION OF CONNECTOR
6.CHECK CONNECTION OF CONNECTOR
a.

Turn the ignition switch is off.


b.

Check that the connectors are properly connected to the telephone transceiver assembly, transponder key ECU assembly and ECM.

OK:

Connectors are properly connected.



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER - ECM)

NG

CONNECT CONNECTOR CORRECTLY

7.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER - ECM)
a.

Disconnect the G144 telephone transceiver assembly connector.


b.

Disconnect the G38*1, G146*2, G148*3 or G156*4 ECM connector.

*1: for 1KD-FTV (except DPF and i-ART), 2KD-FTV (except DPF)

*2: for 2TR-FBE

*3: for 1KD-FTV (for DPF), 2KD-FTV (for DPF)

*4: for 1KD-FTV (for i-ART)



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1KD-FTV (except DPF and i-ART), 2KD-FTV (except DPF):
Tester Connection Condition Specified Condition
G144-7 (BLK2) - G38-29 (IMO) Always Below 1 Ω
G144-8 (BLK3) - G38-30 (IMI) Always Below 1 Ω
G144-7 (BLK2) or G38-29 (IMO) - Body ground Always 10 kΩ or higher
G144-8 (BLK3) or G38-30 (IMI) - Body ground Always 10 kΩ or higher

for 2TR-FBE:
Tester Connection Condition Specified Condition
G144-7 (BLK2) - G146-32 (IMO) Always Below 1 Ω
G144-8 (BLK3) - G146-31 (IMI) Always Below 1 Ω
G144-7 (BLK2) or G146-32 (IMO) - Body ground Always 10 kΩ or higher
G144-8 (BLK3) or G146-31 (IMI) - Body ground Always 10 kΩ or higher

for 1KD-FTV (for DPF), 2KD-FTV (for DPF):
Tester Connection Condition Specified Condition
G144-7 (BLK2) - G148-29 (IMO) Always Below 1 Ω
G144-8 (BLK3) - G148-28 (IMI) Always Below 1 Ω
G144-7 (BLK2) or G148-29 (IMO) - Body ground Always 10 kΩ or higher
G144-8 (BLK3) or G148-28 (IMI) - Body ground Always 10 kΩ or higher

for 1KD-FTV (for i-ART):
Tester Connection Condition Specified Condition
G144-7 (BLK2) - G156-29 (IMO) Always Below 1 Ω
G144-8 (BLK3) - G156-28 (IMI) Always Below 1 Ω
G144-7 (BLK2) or G156-29 (IMO) - Body ground Always 10 kΩ or higher
G144-8 (BLK3) or G156-28 (IMI) - Body ground Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for 1KD-FTV (except DPF and i-ART), 2KD-FTV (except DPF):
Tester Connection Condition Specified Condition
G144-7 (BLK2) or G38-29 (IMO) - Body ground Always Below 1 V
G144-8 (BLK3) or G38-30 (IMI) - Body ground Always Below 1 V

for 2TR-FBE:
Tester Connection Condition Specified Condition
G144-7 (BLK2) or G146-32 (IMO) - Body ground Always Below 1 V
G144-8 (BLK3) or G146-31 (IMI) - Body ground Always Below 1 V

for 1KD-FTV (for DPF), 2KD-FTV (for DPF):
Tester Connection Condition Specified Condition
G144-7 (BLK2) or G148-29 (IMO) - Body ground Always Below 1 V
G144-8 (BLK3) or G148-28 (IMI) - Body ground Always Below 1 V

for 1KD-FTV (for i-ART):
Tester Connection Condition Specified Condition
G144-7 (BLK2) or G156-29 (IMO) - Body ground Always Below 1 V
G144-8 (BLK3) or G156-28 (IMI) - Body ground Always Below 1 V



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER - TRANSPONDER KEY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER - TRANSPONDER KEY ECU)
a.

Disconnect the G144 telephone transceiver assembly connector.


b.

Disconnect the G26 transponder key ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G144-1 (BLK1) - G26-12 (EFII) Always Below 1 Ω
G144-1 (BLK1) or G26-12 (EFII) - Body ground Always 10 kΩ or higher
G144-2 (BLK4) - G26-13 (EFIO) Always Below 1 Ω
G144-2 (BLK4) or G26-13 (EFIO) - Body ground Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G144-1 (BLK1) or G26-12 (EFII) - Body ground Always Below 1 V
G144-2 (BLK4) or G26-13 (EFIO) - Body ground Always Below 1 V



Result:
Proceed to
OK
NG



OK

9.REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Temporarily replace the transponder key ECU assembly with a new one (Refer to the Service Bulletin).


Result:
Proceed to
NEXT



NEXT

10.REGISTER ECU COMMUNICATION ID
10.REGISTER ECU COMMUNICATION ID
a.

Register the ECU - ECM communication ID (Refer to the Service Bulletin).


Result:
Proceed to
NEXT



NEXT

11.CLEAR DTC
11.CLEAR DTC

Result:
Proceed to
NEXT



NEXT

12.CHECK FOR DTC
12.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>BLOCKING SYSTEM>DTC CHECK / CLEAR

OK:

DTC B1587 is not output.



Result:
Proceed to
OK
NG



OK

END (TRANSPONDER KEY ECU IS DEFECTIVE)

NG

13.REPLACE ECM
13.REPLACE ECM
a.

Temporarily replace the ECM with a new one.



Result:
Proceed to
NEXT



NEXT

14.REGISTER ECU COMMUNICATION ID
14.REGISTER ECU COMMUNICATION ID
a.

Register the ECU - ECM communication ID (Refer to the Service Bulletin).


Result:
Proceed to
NEXT



NEXT

15.CLEAR DTC
15.CLEAR DTC

Result:
Proceed to
NEXT



NEXT

16.CHECK FOR DTC
16.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>BLOCKING SYSTEM>DTC CHECK / CLEAR

OK:

DTC B1587 is not output.



Result:
Proceed to
OK
NG



OK

END (ECM IS DEFECTIVE)

NG

REPLACE TELEPHONE TRANSCEIVER ASSEMBLY