The fuel pressure sensor mounted on the common rail converts the fuel pressure inside the common rail into an electrical signal and outputs the signal to the ECM. The ECM controls the supply pump in order to maintain the fuel pressure inside the common rail at a target pressure calculated by the ECM. Refer to System Description (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>SYSTEM DESCRIPTION).
If the drop in the internal fuel pressure is large when injecting fuel, the ECM interprets this as a fault and stores P0093.
If P0093 is present, refer to "Diagnostic Trouble Code (DTC) Table for Common Rail System" (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>SYSTEM DESCRIPTION).
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0093 | Fuel System Leak Detected - Large Leak | The fuel pressure decreases greatly when the engine is running.
(1 trip detection logic) |
·
Fuel line between fuel supply pump assembly and common rail assembly ·
Fuel line between common rail assembly and each injector assembly ·
Suction control valve (fuel supply pump assembly) ·
Common rail assembly ·
Injector assembly ·
Pressure discharge valve (common rail assembly) ·
Fuel pressure sensor (common rail assembly) ·
Crankshaft position sensor ·
Fuel filter element sub-assembly ·
Open or short in injector driver circuit (P0200 stored simultaneously) ·
Open or short in injector circuit ·
Injector driver (P0200 stored simultaneously) ·
ECM |
Comes on | DTC stored |
| DTC No. | Data List |
|---|---|
| P0093 | ·
Fuel Press ·
Target Common Rail Pressure |
When DTC P0093 is set, check the internal fuel pressure of the common rail by entering the following menus on the intelligent tester: Powertrain / Engine and ECT / Data List / Fuel Press.
| Engine Speed | Fuel Pressure |
|---|---|
| Idling | Approximately 25000 to 35000 kPa |
| 3000 rpm (No engine load) | Approximately 28000 to 48000 kPa |
| DTC Detection Drive Pattern | After idling for 60 seconds, run engine at 2500 rpm for 30 seconds.
Fully depress the accelerator pedal for 5 seconds, and then release it. (*A) Rev the engine to 3000 rpm and fully release the accelerator pedal immediately after the engine reaches 3000 rpm. (*B) Repeat procedures (*A) and (*B) 5 times. |
This DTC indicates that fuel leaks exist in high pressure areas in the common rail system. The ECM constantly monitors the internal fuel pressure of the common rail after the engine is started. The ECM stores this DTC if the drop in the internal fuel pressure is large when injecting fuel.
In the common rail system, high-pressure fuel is always supplied to the high-pressure areas including the fuel supply pump assembly, common rail assembly, injector assemblies and piping. The ECM adjusts the suction control valve opening angle to obtain the target internal fuel pressure.
If this DTC is stored, the ECM enters fail-safe mode. In fail-safe mode, both fuel injection and fuel supply pump assembly operation are suspended, and then the engine is stopped. Before the engine is stopped, the ECM permits the vehicle to be driven for 1 minute. The ECM continues operating in fail-safe mode until the ignition switch is turned off.
| Required sensors | Fuel pressure sensor |
| Frequency of operation | Continuous |
| Duration | 1 second |
| MIL operation | 1 driving cycle |
Soon after starting the engine, visually check for fuel leaks in the fuel line.
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>REGISTRATION) and initialization (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>INITIALIZATION).
After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>INITIALIZATION).
After replacing a injector assembly, the ECM needs registration (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>REGISTRATION).
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
The following can be deduced from the above freeze frame data:
The common rail fuel pressure dropped suddenly when the engine was being run at a moderate engine speed during engine warmup and DTC P0093 was stored at the point when data set 4 was recorded.
Injection Feedback Val #3 is 5.0 mm3/st which is large (the normal value is between -3.0 and 3.0 mm3/st) and indicates that the injector assembly of cylinder 3 may be malfunctioning.
Actual cause: In this case, foreign matter in the fuel is stuck inside an injector assembly causing the injector assembly to malfunction temporarily.
In order to remove the foreign matter in the fuel (the main cause of the problem), the fuel filter case needs to be cleaned and the fuel filter needs to be replaced.
*1: Fuel press suddenly decreases for a moment, and then recovers. This can be seen clearly by comparing it to target common rail pressure.
*2: Injection Feedback Val #3 is 5.0 mm3/st which is large (the normal value is between -3.0 and 3.0 mm3/st) and indicates that the injector assembly of cylinder 3 may be malfunctioning.
| Data List | Value | Unit |
|---|---|---|
| Engine Speed | 1478 | rpm |
| Fuel Press | 8900 | kPa |
| Target Common Rail Pressure | 65320 | kPa |
| Injection Volume (Point A) | 51.26 | mm3/st |
| Injection Volume (Point A`) | 9.76 | mm3/st |
| Accel Position | 63.67 | % |
| Injection Feedback Val #1 | -1.1 | mm3/st |
| Injection Feedback Val #2 | -2.5 | mm3/st |
| Injection Feedback Val #3 | 5.0 | mm3/st |
| Injection Feedback Val #4 | -1.8 | mm3/st |
| MIL | ON | - |
Before starting the engine, visually check for fuel leaks from the fuel supply pump assembly, injector assembly, common rail assembly, and the fuel pipes in high-pressure areas.
No fuel leaks in high-pressure areas.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs and freeze frame data.
| Result | Proceed to |
|---|---|
| P0093 and "P0190, P0192 and/or P0193" are output | C |
| P0093 and "P0335, P0339 and/or P0340" are output | B |
| Except above | A |
A
B
C
Check if the fuel level is low.
| Result | Proceed to |
|---|---|
| The indicator (fuel warning light) is illuminated | A |
| The indicator (fuel warning light) is not illuminated | B |
A
B
Add fuel.
| Proceed to |
|---|
| NEXT |
NEXT
Using the hand pump mounted on the fuel filter cap, bleed the air from the fuel system. Continue pumping until the pump resistance increases.
Hand pump pumping speed: Max. 2 strokes/sec.
The hand pump must be pushed with a full stroke during pumping.
When the fuel pressure at the supply pump inlet port reaches a saturated pressure, the hand pump resistance increases.
If pumping is interrupted during the air bleeding process, fuel in the fuel line may return to the fuel tank. Continue pumping until the hand pump resistance increases.
If the hand pump resistance does not increase despite consecutively pumping 200 times or more, there may be a fuel leak between the fuel tank and fuel filter element sub-assembly, the hand pump may be malfunctioning, or the vehicle may have run out of fuel.
If a large amount of air remains inside the fuel system, the common rail pressure does not rise to the pressure range necessary for normal use, and the engine cannot be started.
Start the engine.
If a large amount of air remains inside the fuel system, the starter may need to be cranked for 10 seconds or more to start the engine.
Do not crank the engine continuously for more than 20 seconds. The battery may be discharged.
Use a fully-charged battery.
When the engine can be started, proceed to the next step.
If the engine cannot be started, bleed the air again using the hand pump until the hand pump resistance increases. Then start the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the intelligent tester on.
Clear the DTCs.
Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>DTC CHECK / CLEAR
Start the engine. (*A)
Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak. (*B)
| Tester Display |
|---|
| Test the Fuel Leak |
Perform the following test 5 times with on/off intervals of 10 seconds: Active Test / Test the Fuel Leak. (*C)
Allow the engine to idle for 3 minutes or more after performing the Active Test for the fifth time. (*D)
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read Current DTCs.
When no DTCs are output, the air bleeding is completed.
If any DTCs are output, proceed to the next step.
Repeat steps (*A) to (*D).
Clear the DTCs.
Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>DTC CHECK / CLEAR
Start the engine and warm it up.
Confirm that the shift lever is in neutral and securely apply the parking brake.
Fully depress the accelerator pedal for 5 seconds, and then release it. (*E)
Rev the engine to 3000 rpm and fully release the accelerator pedal immediately after the engine reaches 3000 rpm. (*F)
Repeat procedures (*E) and (*F) 5 times.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read Current DTCs.
| Result | Proceed to |
|---|---|
| DTC is output | A |
| No DTC is output | B |
A
B
Read the value of Injection Feedback Val #1 to #4 in the freeze frame data recorded in Procedure 2.
| Result | Proceed to |
|---|---|
| Injection Feedback Val for at least one cylinder is 5 mm3/st in at least 1 set of freeze frame data | B |
| Except above | A |
When there is a problem with the operation of an injector assembly due to foreign matter in the inside of the injector assembly, etc., the fuel injection volume decreases. As a result, the ECM gives instructions to increase the fuel injection volume, which causes Injection Feedback Val to increase.
A
B
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Clear the DTCs.
Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>DTC CHECK / CLEAR
Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press.
| Tester Display |
|---|
| Fuel Press |
Start the engine.
Read the value of Fuel Press while cranking and idling the engine.
| Result | Proceed to |
|---|---|
| The engine cannot be started or the engine can be started but Fuel Press is below 20000 kPa 2 seconds after the starter signal changes from OFF to ON | B |
| Except above | A |
A
B
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Start the engine and warm it up.
Enter the following menus: Powertrain / Engine and ECT / Data List / Injection Feedback Val #1 to #4.
| Tester Display |
|---|
| Injection Feedback Val #1 |
| Injection Feedback Val #2 |
| Injection Feedback Val #3 |
| Injection Feedback Val #4 |
Read the values.
| Tester Display | Engine Condition* | Normal Value |
|---|---|---|
| Injection Feedback Val #1
Injection Feedback Val #2 Injection Feedback Val #3 Injection Feedback Val #4 |
Idling | -3.0 mm3/st to 3.0 mm3/st |
*: The A/C switch and all accessory switches should be off, the engine coolant temperature should be 70°C (158°F) or higher and the engine should be idled for 1 minute or more.
| Result | Proceed to |
|---|---|
| Injection Feedback Val for at least one cylinder is more than 3 mm3/st and engine vibration is abnormally large | B |
| Except above | A |
When there is a problem with the operation of a injector assembly due to foreign matter in the inside of the injector assembly, etc., the fuel injection volume decreases. As a result, the ECM gives instructions to increase the fuel injection volume, which causes Injection Feedback Val to increase.
The ECM controls the system so that the sum of Injection Feedback Val for all of the cylinders is approximately 0 mm3/st. Even if the value of Injection Feedback Val for a cylinder is less than -3.0 mm3/st (-3.0 mm3/st is the lowest normal value), as long as the value of Injection Feedback Val for each of the other cylinders is 3.0 mm3/st or less, the injector assemblies are not malfunctioning.
A
B
Start the engine and drive the vehicle until the engine coolant temperature reaches 60°C (140°F) or higher.
Stop the vehicle and allow the engine to idle.
While checking the tachometer, fully depress the accelerator pedal for 5 seconds, and then release it.*1
Repeat procedure *1 5 times.
| Result | Proceed to |
|---|---|
| No problems such as sluggishness or variations in the tachometer reading | A |
| Except above | B |
A
B
Replace the fuel filter element sub-assembly.
| Proceed to |
|---|
| NEXT |
NEXT
Bleed the air from the fuel system.
Click hereEngine / Hybrid System>2KD-FTV FUEL>FUEL SYSTEM(w/o DPF)>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| NEXT |
NEXT
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak / Data List / Fuel Press, Target Common Rail Pressure, and Target Pump SCV Current.
| Active Test Display |
|---|
| Test the Fuel Leak |
| Data List Display |
|---|
| Target Common Rail Pressure |
| Fuel Press |
| Target Pump SCV Current |
| *1 | Snapshot Button |
Take a snapshot with the intelligent tester during the Active Test.
Detailed graphs can be displayed by transferring the stored snapshot from the tester to a PC (personal computer) with Intelligent Viewer installed.
Measure the difference between the target fuel pressure (Target Common Rail Pressure) and the actual fuel pressure (Fuel Press) when the "Test the Fuel Leak" Active Test is performed.
Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>DATA LIST / ACTIVE TEST
In order to obtain an exact measurement, perform the Active Test 5 times and measure the difference once each time the Active Test is performed.
The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10000 kPa.
"Target Common Rail Pressure" is the target fuel pressure controlled by the ECM.
"Fuel Press" is the actual fuel pressure.
| Result | Proceed to |
|---|---|
| The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10000 kPa | A |
| Except above | B |
A
B
Use this Active Test to determine the malfunctioning cylinder.
Connect the intelligent tester to the DLC3.
Start the engine and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Cylinder #1 to #4 Fuel Cut.
| Tester Display |
|---|
| Control the Select Cylinder Fuel Cut |
If the engine idle speed does not change when a injector assembly is disabled, the cylinder being tested is malfunctioning. Record any malfunctioning cylinders.
If the cylinder being tested is normal, there will be a significant change in idle speed when the fuel injection is stopped for that cylinder.
| Proceed to |
|---|
| NEXT |
NEXT
Remove the glow plug for all the cylinders.
Click hereEngine / Hybrid System>2KD-FTV STARTING>GLOW PLUG(w/o DPF)>REMOVAL
Visually check if there is fuel on the glow plugs.
If there is fuel on a glow plug assembly, fuel may be leaking from an injector assembly.
After replacing an injector assembly, make sure that the common rail pressure (fuel pressure) is within 5000 kPa (51.0 kgf/cm2, 725 psi) of the target fuel pressure while cranking the engine.
If there is fuel on a glow plug assembly, fuel may have mixed with the engine oil. Check the engine oil amount and whether the engine oil smells of diesel fuel. If the oil level is above the full line or the engine oil smells of diesel fuel, replace the engine oil.
Install the glow plug.
Click hereEngine / Hybrid System>2KD-FTV STARTING>GLOW PLUG(w/o DPF)>INSTALLATION
| Proceed to |
|---|
| NEXT |
NEXT
Replace the injector assembly of the malfunctioning cylinder.
Click hereEngine / Hybrid System>2KD-FTV FUEL>FUEL INJECTOR(w/o DPF)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Bleed the air from the fuel system.
Click hereEngine / Hybrid System>2KD-FTV FUEL>FUEL SYSTEM(w/o DPF)>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| NEXT |
NEXT
Register the injector compensation code.
Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>REGISTRATION
Perform the injector pilot quantity learning.
Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>REGISTRATION
| Proceed to |
|---|
| NEXT |
NEXT
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.
| Tester Display |
|---|
| Engine Speed |
Read the value while cranking and idling the engine.
| Tester Display | Engine Condition | Specified Condition |
|---|---|---|
| Engine Speed | Cranking | 50 to 400 rpm |
| Idling with warm engine | 700 to 800 rpm |
The value should be the same as the actual engine speed and displayed with no interruption on the tester.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(ECM) |
Connect the positive (+) probe of an oscilloscope to the fuel pressure sensor input terminal of the ECM connector and the negative (-) probe to the body ground.
Turn the ignition switch to ON.
Check for any noise in the waveform when vibration is applied to the wire harness and connectors between the fuel pressure sensor and ECM.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C22-26 (PCR1) - Body ground | Vibration is applied to the wire harness and connectors | No noise in the waveform |
| Result | Proceed to |
|---|---|
| MIL comes on or noise present in the waveform | B |
| Except above | A |
A
B
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Temperature.
| Tester Display |
|---|
| Fuel Temperature |
Read the value.
The value is almost the same as the actual fuel temperature.
When the engine is stopped and left overnight, the fuel temperature becomes the same as the ambient temperature.
If there is a problem with the fuel temperature sensor, and a fuel temperature value lower than the actual fuel temperature is indicated, P0093 may be stored.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for intermittent problems.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the crankshaft position sensor.
Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>CRANKSHAFT POSITION SENSOR>REMOVAL
Before replacing the crankshaft position sensor, perform a wire harness inspection and if there are any problems with the wire harness, repair or replace it.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the fuel temperature sensor.
Before replacing the fuel temperature sensor, perform a wire harness inspection and if there are any problems with the wire harness, repair or replace it.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Clear the DTCs.
Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>DTC CHECK / CLEAR
Start the engine.
Warm up the engine (engine coolant temperature is 70°C (158°F) or higher).
Confirm that the shift lever is in neutral and securely apply the parking brake.
Fully depress the accelerator pedal for 5 seconds, and then release it. (*A)
Rev the engine to 3000 rpm and fully release the accelerator pedal immediately after the engine reaches 3000 rpm. (*B)
Repeat procedures (*A) and (*B) 5 times.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
No DTCs are output.
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Component with harness connected
(ECM) |
Connect the positive (+) probe of an oscilloscope to the fuel pressure sensor input terminal of the ECM connector and the negative (-) probe to the body ground.
Turn the ignition switch to ON.
Check for any noise in the waveform when vibration is applied to the wire harness and connectors between the fuel pressure sensor and ECM.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C22-26 (PCR1) - Body ground | Vibration is applied to the wire harness and connectors | No noise in the waveform |
| Result | Proceed to |
|---|---|
| MIL comes on or noise present in the waveform | A |
| Except above | B |
A
B
Replace the common rail assembly.
Click hereEngine / Hybrid System>2KD-FTV FUEL>COMMON RAIL(w/o DPF)>REMOVAL
Before replacing the common rail assembly, perform a wire harness inspection and if there are any problems with the wire harness, repair or replace it.
| Proceed to |
|---|
| NEXT |
NEXT
Bleed the air from the fuel system.
Click hereEngine / Hybrid System>2KD-FTV FUEL>FUEL SYSTEM(w/o DPF)>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| NEXT |
NEXT